Anita Setyowati Srie Gunarti
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Anita Setyowati Srie Gunarti has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- As’aD Munawir
Universitas Brawijaya
3 shared publications - Eko Andi Suryo
Universitas Brawijaya
3 shared publications - Harimurti Harimurti
Brawijaya University
3 shared publications - Yulvi Zaika
Brawijaya University
3 shared publications - Irwan Raharja
Department of Accounting Information Systems, Universitas Bina Sarana Informatika, Jl. Banten No. 1, Karangpawitan, Karawang Barat, West Java, Indonesia
2 shared publications - Eko Darma
Program Studi Teknik sipil, Universitas Islam 45 Bekasi
1 shared publication
Latest Publications
- Open Access
- 29 September 2025
- Published by OU Scientific Route in EUREKA: Physics and Engineering
- No. 6,p. 108-117
Optimizing subgrade on Karawang expansive soil using industrial waste: effect on bearing pressure ratio
The rainy season often causes water pooling on the ground surface, a rise in groundwater levels, and swelling in expansive soils. Swelling in expansive soils has poor mechanical properties, resulting in low subgrade bearing capacity, which makes road construction prone to damage. Improving expansive soil subgrades using waste materials with specific properties that can effectively reduce swelling potential has proven to be effective. This study aims to identify the optimal thickness of stabilized expansive soil subgrade using fly ash (FA) and waste foundry sand (WFS) that can reduce swelling potential and improve bearing pressure characteristics under wet conditions. The concentration of FA used was 15%, whereas the concentration of WFS was 20%; both were based on the soil’s dry weight and modeled as a 30 cm-high subgrade with varying stabilized soil thicknesses. In this study, a swelling test was conducted by introducing water into the subgrade, followed by a plate load test to determine the bearing pressure and settlement. Loading tests were conducted on 5 subgrade variants that had undergone curing for 4 days and wetting for 4 days. The results of the wetting and swelling tests on the stabilized soil subgrade with a thickness of 30 cm (V4) showed a smaller swelling percentage compared to subgrade V0, reducing swelling from 7% to 3.7% due to changes in moisture content, and reduced the swelling pressure from 50.17 kPa to 25.34 kPa. Subgrade V4 reduced the swelling potential and swelling pressure by almost 2 times that of the untreated soil subgrade variant (V0). The subgrade with the best performance under wet conditions is subgrade V4, with a 100% improvement, which is a 30 cm thick stabilized soil layer, showing a pressure increase of 214.91% compared to the untreated soil subgrade (V0) at a 7 mm settlement with a BPR of 3.15
- 29 September 2025
- Published by OU Scientific Route in EUREKA: Physics and Engineering
- No. 6,p. 108-117
Open AccessOptimizing subgrade on Karawang expansive soil using industrial waste: effect on bearing pressure ratio
The rainy season often causes water pooling on the ground surface, a rise in groundwater levels, and swelling in expansive soils. Swelling in expansive soils has poor mechanical properties, resulting in low subgrade bearing capacity, which makes road construction prone to damage. Improving expansive soil subgrades using waste materials with specific properties that can effectively reduce swelling potential has proven to be effective. This study aims to identify the optimal thickness of stabilized expansive soil subgrade using fly ash (FA) and waste foundry sand (WFS) that can reduce swelling potential and improve bearing pressure characteristics under wet conditions. The concentration of FA used was 15%, whereas the concentration of WFS was 20%; both were based on the soil’s dry weight and modeled as a 30 cm-high subgrade with varying stabilized soil thicknesses. In this study, a swelling test was conducted by introducing water into the subgrade, followed by a plate load test to determine the bearing pressure and settlement. Loading tests were conducted on 5 subgrade variants that had undergone curing for 4 days and wetting for 4 days. The results of the wetting and swelling tests on the stabilized soil subgrade with a thickness of 30 cm (V4) showed a smaller swelling percentage compared to subgrade V0, reducing swelling from 7% to 3.7% due to changes in moisture content, and reduced the swelling pressure from 50.17 kPa to 25.34 kPa. Subgrade V4 reduced the swelling potential and swelling pressure by almost 2 times that of the untreated soil subgrade variant (V0). The subgrade with the best performance under wet conditions is subgrade V4, with a 100% improvement, which is a 30 cm thick stabilized soil layer, showing a pressure increase of 214.91% compared to the untreated soil subgrade (V0) at a 7 mm settlement with a BPR of 3.15
- Open Access
- 21 August 2024
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 4 (1 (130)) , 27-36
Identifying the effect of subgrade layer thickness of soil stabilized with waste foundry sand and fly ash on bearing capacity
The issue of subgrade soil often involves unstable soil properties, such as low bearing capacity, susceptibility to expansion and shrinkage, and vulnerability to erosion and deformation due to traffic loads and weather conditions. Unstable subgrade soil can cause various infrastructure problems, including cracks, settlement, and damage to road surfaces. Therefore, stabilizing subgrade soil is an important step to ensure the reliability and longevity of highways. One effective and sustainable method for subgrade soil stabilization is by utilizing local waste materials. The use of local waste materials such as fly ash (FA) and waste foundry sand (WFS) not only improves the physical and mechanical properties of the soil but also helps reduce environmental impact by repurposing pollutants. This study aims to analyze the effect of the thickness of subgrade layers stabilized with FA and WFS on bearing capacity. The initial stage includes examining the physical and mechanical properties of natural soil and soil stabilized with FA and WFS. The waste content used is 9 % FA and 15 % WFS by dry weight of the soil. Subgrade modeling was conducted using a steel box measuring 60×60×60 cm with a soil thickness of 30 cm. Load testing was carried out on 5 layer variants that had undergone 4 days of curing. The study results found that the ultimate bearing capacity (qult) of 890 kPa was produced by the V4 layer, which is a subgrade with a 30 cm thick layer of soil stabilized with FA and WFS at a settlement of 6 mm. The bearing capacity ratio of 2.87 means that the subgrade with a 30 cm thick layer of soil stabilized with FA and WFS experienced an improvement in bearing capacity of 2.87 times that of the subgrade with untreated soil material. The results obtained can be applied in practice to the local geotechnical conditions of the project site in West Java, including natural soil properties and seasonal changes
- 21 August 2024
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 4 (1 (130)) , 27-36
Open AccessIdentifying the effect of subgrade layer thickness of soil stabilized with waste foundry sand and fly ash on bearing capacity
The issue of subgrade soil often involves unstable soil properties, such as low bearing capacity, susceptibility to expansion and shrinkage, and vulnerability to erosion and deformation due to traffic loads and weather conditions. Unstable subgrade soil can cause various infrastructure problems, including cracks, settlement, and damage to road surfaces. Therefore, stabilizing subgrade soil is an important step to ensure the reliability and longevity of highways. One effective and sustainable method for subgrade soil stabilization is by utilizing local waste materials. The use of local waste materials such as fly ash (FA) and waste foundry sand (WFS) not only improves the physical and mechanical properties of the soil but also helps reduce environmental impact by repurposing pollutants. This study aims to analyze the effect of the thickness of subgrade layers stabilized with FA and WFS on bearing capacity. The initial stage includes examining the physical and mechanical properties of natural soil and soil stabilized with FA and WFS. The waste content used is 9 % FA and 15 % WFS by dry weight of the soil. Subgrade modeling was conducted using a steel box measuring 60×60×60 cm with a soil thickness of 30 cm. Load testing was carried out on 5 layer variants that had undergone 4 days of curing. The study results found that the ultimate bearing capacity (qult) of 890 kPa was produced by the V4 layer, which is a subgrade with a 30 cm thick layer of soil stabilized with FA and WFS at a settlement of 6 mm. The bearing capacity ratio of 2.87 means that the subgrade with a 30 cm thick layer of soil stabilized with FA and WFS experienced an improvement in bearing capacity of 2.87 times that of the subgrade with untreated soil material. The results obtained can be applied in practice to the local geotechnical conditions of the project site in West Java, including natural soil properties and seasonal changes
- Open Access
- 22 December 2023
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 6 (6 (126)) , 31-40
Identifying the microstructure and mechanical properties of expansive soil stabilized using fly ash and waste foundry sand
Expansive soil causes road construction damage in the form of cracks or deformations due to changes in moisture content. One method to address this issue is soil stabilization using additive materials. Special additives can sometimes be expensive; hence it is necessary to use additive materials based on industrial waste as a waste management solution to solve the problem of expansive soil as a road construction subgrade. This study aims to analyze the effects of adding two types of industrial waste, namely fly ash (FA) and waste foundry sand (WFS), regarding the microstructure, physical, and mechanical properties of expansive soil. The method of stabilizing expansive soil involves mixing the soil with 9 % FA and various levels of WFS (0 %, 7.5 %, 10 %, 15 %) based on the dry weight of the soil. Microstructure testing includes quantitative X-ray diffraction and scanning electron microscopy. Physical property testing includes specific gravity, Atterberg limits and sieve analysis. Mechanical testing, i.e. compaction, California Bearing Ratio, swelling, and Triaxial tests were conducted. Soil stabilized with 9 % FA and 15 % WFS shows a significant increase in the internal friction angle and cohesion, reducing swelling by 67.18 % compared to the original soil swelling. The addition of 9 % fly ash and 15 % WFS to expansive soil reduces the content of montmorillonite. Natural expansive soils have a very poor soaked CBR of 0.94 %, while stabilized soils with 9 % FA and 15 % WFS have a soaked CBR of 6.46 %. This means that the soaked CBR of the stabilized soil meets the minimum CBR required for road subgrade construction. A mixture of 9 % FA and 15 % WFS in expansive soil can be recommended as a material for stabilizing expansive soil due to its ability to improve microstructure and mechanical properties
- 22 December 2023
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 6 (6 (126)) , 31-40
Open AccessIdentifying the microstructure and mechanical properties of expansive soil stabilized using fly ash and waste foundry sand
Expansive soil causes road construction damage in the form of cracks or deformations due to changes in moisture content. One method to address this issue is soil stabilization using additive materials. Special additives can sometimes be expensive; hence it is necessary to use additive materials based on industrial waste as a waste management solution to solve the problem of expansive soil as a road construction subgrade. This study aims to analyze the effects of adding two types of industrial waste, namely fly ash (FA) and waste foundry sand (WFS), regarding the microstructure, physical, and mechanical properties of expansive soil. The method of stabilizing expansive soil involves mixing the soil with 9 % FA and various levels of WFS (0 %, 7.5 %, 10 %, 15 %) based on the dry weight of the soil. Microstructure testing includes quantitative X-ray diffraction and scanning electron microscopy. Physical property testing includes specific gravity, Atterberg limits and sieve analysis. Mechanical testing, i.e. compaction, California Bearing Ratio, swelling, and Triaxial tests were conducted. Soil stabilized with 9 % FA and 15 % WFS shows a significant increase in the internal friction angle and cohesion, reducing swelling by 67.18 % compared to the original soil swelling. The addition of 9 % fly ash and 15 % WFS to expansive soil reduces the content of montmorillonite. Natural expansive soils have a very poor soaked CBR of 0.94 %, while stabilized soils with 9 % FA and 15 % WFS have a soaked CBR of 6.46 %. This means that the soaked CBR of the stabilized soil meets the minimum CBR required for road subgrade construction. A mixture of 9 % FA and 15 % WFS in expansive soil can be recommended as a material for stabilizing expansive soil due to its ability to improve microstructure and mechanical properties
- Open Access
- 23 April 2023
- Published by Universitas Borneo Tarakan in Borneo Engineering: Jurnal Teknik Sipil
- Vol. 1 (1) , 39-48
Micro-analysis Tanah Ekspansif yang Diperbaiki Secara Kimiawi
Road construction on expansive soil faces many problems such as deflection, longitudinal cracks, circular cracks and spreading cracks in road construction due to the large nature of swelling and shrinkage. This study aims to identify changes in the mineralogy microstructure and chemical properties of the soil in chemically corrected expansive soils so that solutions for expansive soil improvement are obtained by utilizing local materials based on industrial waste, namely Fly ash and Waste Foundry Sand. The research method is in the form of laboratory experiments, namely Structure Electron Microscope and XRD tests on native soil and soil stabilized with Fly ash and Waste Foundry Sand to analyze mineral structure and chemical changes. The results of the analysis found that the effect of the two types of additives on expansive soils was descriptively significant. The addition of fly ash and WFS to the soil makes the pores and cracks filled with fly ash particles and some form of hydration. After the addition of Fly ash and WFS, ion exchange and pozzolanic reactions from fly ash occur to make the flake and flocculant structure of the soil cement into a crystal or block structure, thereby increasing the compactness and integrity of the soil sample.
- 23 April 2023
- Published by Universitas Borneo Tarakan in Borneo Engineering: Jurnal Teknik Sipil
- Vol. 1 (1) , 39-48
Open AccessMicro-analysis Tanah Ekspansif yang Diperbaiki Secara Kimiawi
Road construction on expansive soil faces many problems such as deflection, longitudinal cracks, circular cracks and spreading cracks in road construction due to the large nature of swelling and shrinkage. This study aims to identify changes in the mineralogy microstructure and chemical properties of the soil in chemically corrected expansive soils so that solutions for expansive soil improvement are obtained by utilizing local materials based on industrial waste, namely Fly ash and Waste Foundry Sand. The research method is in the form of laboratory experiments, namely Structure Electron Microscope and XRD tests on native soil and soil stabilized with Fly ash and Waste Foundry Sand to analyze mineral structure and chemical changes. The results of the analysis found that the effect of the two types of additives on expansive soils was descriptively significant. The addition of fly ash and WFS to the soil makes the pores and cracks filled with fly ash particles and some form of hydration. After the addition of Fly ash and WFS, ion exchange and pozzolanic reactions from fly ash occur to make the flake and flocculant structure of the soil cement into a crystal or block structure, thereby increasing the compactness and integrity of the soil sample.
- Open Access
- 1 May 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 856 (1)
Mechanical Properties Improvement of Clays Using Silica Sand Waste and Dust Sand Foundry Waste
The increase of industrial waste and many road damages due to unstable subgrade invite the research on soil additives made from waste treatment as stabilizers to improve the mechanical value of clay. This study used California Bearing Ratio Test based on the ASTM standard for mechanical properties testing of clay. The soil stabilization method was carried out by mixing the clay with Silica Sand waste and Dust Sand Foundry waste in a predetermined composition. California Bearing Ratio value of 2.5 mm penetration showed a significant increase of 47.9% from the original clay in the composition of the waste 5% Silica Sand and 5% Dust Sand Foundry.
- 1 May 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 856 (1)
Open AccessMechanical Properties Improvement of Clays Using Silica Sand Waste and Dust Sand Foundry Waste
The increase of industrial waste and many road damages due to unstable subgrade invite the research on soil additives made from waste treatment as stabilizers to improve the mechanical value of clay. This study used California Bearing Ratio Test based on the ASTM standard for mechanical properties testing of clay. The soil stabilization method was carried out by mixing the clay with Silica Sand waste and Dust Sand Foundry waste in a predetermined composition. California Bearing Ratio value of 2.5 mm penetration showed a significant increase of 47.9% from the original clay in the composition of the waste 5% Silica Sand and 5% Dust Sand Foundry.
- Open Access
- 1 April 2020
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1517 (1)
Unconfined compression strength of soil using silica sand waste and dust sand foundry as a stabilizer
The need to improve the subgrade of a highway becomes urgent when the vehicle load exceeds the carrying capacity of the soil. Industrial waste, that increase every day, was proposed in this study as an additive or stabilizer to improve the carrying capacity of the subgrade. Testing was done through laboratory experiments of the mixing original soil with Silica Sand waste and Dust Sand Foundry waste in certain compositions. To test the mechanical properties, the Unconfined Compression Strength Test based on ASTM standards was conducted. The unconfined compression strength (qu) value of the original soil was 0.289 kg/cm2. The highest qu value was shown in the composition of the soil mixture with 2.5% SS and 7.5% DSF which was 0.347 kg/cm2. The qu value increased by 20.07% from the qu value of the original soil, and showed a mechanical improvement in stabilizing soil.
- 1 April 2020
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1517 (1)
Open AccessUnconfined compression strength of soil using silica sand waste and dust sand foundry as a stabilizer
The need to improve the subgrade of a highway becomes urgent when the vehicle load exceeds the carrying capacity of the soil. Industrial waste, that increase every day, was proposed in this study as an additive or stabilizer to improve the carrying capacity of the subgrade. Testing was done through laboratory experiments of the mixing original soil with Silica Sand waste and Dust Sand Foundry waste in certain compositions. To test the mechanical properties, the Unconfined Compression Strength Test based on ASTM standards was conducted. The unconfined compression strength (qu) value of the original soil was 0.289 kg/cm2. The highest qu value was shown in the composition of the soil mixture with 2.5% SS and 7.5% DSF which was 0.347 kg/cm2. The qu value increased by 20.07% from the qu value of the original soil, and showed a mechanical improvement in stabilizing soil.
- Open Access
- 23 October 2017
- Published by Badan Penelitian dan Pengembangan Daerah Provinsi Jawa Barat in CR JOURNAL (CREATIVE RESEARCH FOR WEST JAVA DEVELOPMENT)
- Vol. 3 (01) , 1-12
Bambu Sebagai Tulangan Pada Perkerasan Kaku (Rigid Pavement) Jalan Raya
Bambu mempunyai sifat mekanik yang baik karena hampir menyerupai sifat mekanik baja. Oleh karena itu penggunaan bambu dapat digunakan pada konstruksi bangunan sipil lainnya sebagai material alternatif pengganti baja seperti perkerasan kaku (rigid pavement) jalan raya. Pada perkerasan kaku jalan raya baja digunakan sebagai tulangan yang berfungsi untuk menahan retak susut akibat suhu dan menambah kapasitas beban jalan.Penelitian ini menggunakan bambu untuk tulangan perkerasan kaku jalan raya. Spesimen yang dibuat adalah meshing (jaringan) tulangan bambu dan tulangan baja dengan panjang 5 m dan lebar 3,5 m, diameter 12 mm dan tiap tulangan dipasang pada jarak setiap 100 mm. Meshing tersebut masing-masing dipasang pada tiap segmen jalan yang berukuran panjang x lebar x tinggi yaitu 3,5 m x 5 m x 0,3 m pada kedalaman 20 cm dari permukaan jalan dan mutu beton K–300. Uji dilakukan dengan menggunakan beban kendaraan yang divariasikan mulai dari 1000 Kg sampai dengan mendekati 14000 Kg dan diamati respon dari perkerasan kaku seperti defleksi, regangan dan tegangan.Defleksi terbesar pada perkerasan rigid pavement tulangan bambu adalah 0,6 mm pada beban 9323 Kg. Tegangan maksimum yang dihasilkan pada tulangan baja memanjang dan melintang adalah 1062,6 Kg/cm2 dan 686,7 Kg/cm2 dengan nilai E baja 2100000 Kg/cm2, sedangkan pada bambu tegangan terbesar yang dihasilkan adalah 118,62 Kg/ cm2 dan 86,87 Kg/ cm2 dengan nilai E bambu 313810 Kg/cm2 pada kondisi ini tegangan yang terjadi masih dalam batas elastis. Hasil penelitian menunjukkan bambu layak dipakai sebagai tulangan pada rigid pavement jalan raya.
- 23 October 2017
- Published by Badan Penelitian dan Pengembangan Daerah Provinsi Jawa Barat in CR JOURNAL (CREATIVE RESEARCH FOR WEST JAVA DEVELOPMENT)
- Vol. 3 (01) , 1-12
Open AccessBambu Sebagai Tulangan Pada Perkerasan Kaku (Rigid Pavement) Jalan Raya
Bambu mempunyai sifat mekanik yang baik karena hampir menyerupai sifat mekanik baja. Oleh karena itu penggunaan bambu dapat digunakan pada konstruksi bangunan sipil lainnya sebagai material alternatif pengganti baja seperti perkerasan kaku (rigid pavement) jalan raya. Pada perkerasan kaku jalan raya baja digunakan sebagai tulangan yang berfungsi untuk menahan retak susut akibat suhu dan menambah kapasitas beban jalan.Penelitian ini menggunakan bambu untuk tulangan perkerasan kaku jalan raya. Spesimen yang dibuat adalah meshing (jaringan) tulangan bambu dan tulangan baja dengan panjang 5 m dan lebar 3,5 m, diameter 12 mm dan tiap tulangan dipasang pada jarak setiap 100 mm. Meshing tersebut masing-masing dipasang pada tiap segmen jalan yang berukuran panjang x lebar x tinggi yaitu 3,5 m x 5 m x 0,3 m pada kedalaman 20 cm dari permukaan jalan dan mutu beton K–300. Uji dilakukan dengan menggunakan beban kendaraan yang divariasikan mulai dari 1000 Kg sampai dengan mendekati 14000 Kg dan diamati respon dari perkerasan kaku seperti defleksi, regangan dan tegangan.Defleksi terbesar pada perkerasan rigid pavement tulangan bambu adalah 0,6 mm pada beban 9323 Kg. Tegangan maksimum yang dihasilkan pada tulangan baja memanjang dan melintang adalah 1062,6 Kg/cm2 dan 686,7 Kg/cm2 dengan nilai E baja 2100000 Kg/cm2, sedangkan pada bambu tegangan terbesar yang dihasilkan adalah 118,62 Kg/ cm2 dan 86,87 Kg/ cm2 dengan nilai E bambu 313810 Kg/cm2 pada kondisi ini tegangan yang terjadi masih dalam batas elastis. Hasil penelitian menunjukkan bambu layak dipakai sebagai tulangan pada rigid pavement jalan raya.