HHHarimurti Harimurti

Harimurti Harimurti

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Harimurti Harimurti has a total of 5 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Optimizing subgrade on Karawang expansive soil using industrial waste: effect on bearing pressure ratio

    by Anita Setyowati Srie Gunarti, Yulvi Zaika, As’ad Munawir, Eko Andi Suryo, Harimurti Harimurti

    The rainy season often causes water pooling on the ground surface, a rise in groundwater levels, and swelling in expansive soils. Swelling in expansive soils has poor mechanical properties, resulting in low subgrade bearing capacity, which makes road construction prone to damage. Improving expansive soil subgrades using waste materials with specific properties that can effectively reduce swelling potential has proven to be effective. This study aims to identify the optimal thickness of stabilized expansive soil subgrade using fly ash (FA) and waste foundry sand (WFS) that can reduce swelling potential and improve bearing pressure characteristics under wet conditions. The concentration of FA used was 15%, whereas the concentration of WFS was 20%; both were based on the soil’s dry weight and modeled as a 30 cm-high subgrade with varying stabilized soil thicknesses. In this study, a swelling test was conducted by introducing water into the subgrade, followed by a plate load test to determine the bearing pressure and settlement. Loading tests were conducted on 5 subgrade variants that had undergone curing for 4 days and wetting for 4 days. The results of the wetting and swelling tests on the stabilized soil subgrade with a thickness of 30 cm (V4) showed a smaller swelling percentage compared to subgrade V0, reducing swelling from 7% to 3.7% due to changes in moisture content, and reduced the swelling pressure from 50.17 kPa to 25.34 kPa. Subgrade V4 reduced the swelling potential and swelling pressure by almost 2 times that of the untreated soil subgrade variant (V0). The subgrade with the best performance under wet conditions is subgrade V4, with a 100% improvement, which is a 30 cm thick stabilized soil layer, showing a pressure increase of 214.91% compared to the untreated soil subgrade (V0) at a 7 mm settlement with a BPR of 3.15

  • Open Access

    Shaking table test on compacted soil to reduce liquefaction potential

    by Muhammad Fhathur Rachman Asmar, Harimurti Harimurti, Yulvi Zaika

    Liquefaction is a granular soil material from a solid state to a liquid an increase in pore water pressure and a decrease in its effective stress. Liquefaction can cause loss of soil bearing capacity, damaging the construction above it. A simple shaking Table using a one-way vibrating Table is the tool used in this study. The earthquake accelerations used in this study are 0,3 g and 0,5 g earthquake accelerations repair method carried out in the form of compaction. Before the shaking Table test is carried out, laboratory tests are first carried out to determine the soil classification. the soil classification used in this study is SM. The purpose of this research is to determine the time of liquefaction on variations in grain size gradation and density on sand soil liquefaction with different earthquake acceleration. Based on the test results, poorly graded soil is the fastest to deformed. In 0,3 g earthquake acceleration performed total settlement of 10 mm at 100 seconds and a groundwater level in 7 mm at 15 seconds. An acceleration of 0,5 g performed total settlement of 12 mm at 10 seconds and a groundwater level in 7 mm at 15 seconds. The poorly graded soil is improved by compaction. The compacted soil in density of 17,838 kN/m3 performed settlement of 8 mm at 105 seconds and a groundwater level in 6 mm at 40 seconds in 0,3 g earthquake acceleration. The compacted soil in density of 17,995 kN/m3 performed 8 mm at 100 seconds and groundwater level in 7 mm at 20 seconds in 0,5 g earthquake acceleration. The compacted soil in density of 18,563 kN/m3 performed settlement 6 mm at the 100th second and a groundwater level 6 mm at the 25th second in 0,5 g earthquake acceleration. Based on the research results, compaction can reduce liquefaction potential

  • Open Access

    Identifying the effect of subgrade layer thickness of soil stabilized with waste foundry sand and fly ash on bearing capacity

    by Anita Setyowati Srie Gunarti, Yulvi Zaika, As’ad Munawir, Eko Andi Suryo, Harimurti Harimurti

    The issue of subgrade soil often involves unstable soil properties, such as low bearing capacity, susceptibility to expansion and shrinkage, and vulnerability to erosion and deformation due to traffic loads and weather conditions. Unstable subgrade soil can cause various infrastructure problems, including cracks, settlement, and damage to road surfaces. Therefore, stabilizing subgrade soil is an important step to ensure the reliability and longevity of highways. One effective and sustainable method for subgrade soil stabilization is by utilizing local waste materials. The use of local waste materials such as fly ash (FA) and waste foundry sand (WFS) not only improves the physical and mechanical properties of the soil but also helps reduce environmental impact by repurposing pollutants. This study aims to analyze the effect of the thickness of subgrade layers stabilized with FA and WFS on bearing capacity. The initial stage includes examining the physical and mechanical properties of natural soil and soil stabilized with FA and WFS. The waste content used is 9 % FA and 15 % WFS by dry weight of the soil. Subgrade modeling was conducted using a steel box measuring 60×60×60 cm with a soil thickness of 30 cm. Load testing was carried out on 5 layer variants that had undergone 4 days of curing. The study results found that the ultimate bearing capacity (qult) of 890 kPa was produced by the V4 layer, which is a subgrade with a 30 cm thick layer of soil stabilized with FA and WFS at a settlement of 6 mm. The bearing capacity ratio of 2.87 means that the subgrade with a 30 cm thick layer of soil stabilized with FA and WFS experienced an improvement in bearing capacity of 2.87 times that of the subgrade with untreated soil material. The results obtained can be applied in practice to the local geotechnical conditions of the project site in West Java, including natural soil properties and seasonal changes


  • Open Access

    Identifying the microstructure and mechanical properties of expansive soil stabilized using fly ash and waste foundry sand

    by Anita Setyowati Srie Gunarti, Yulvi Zaika, As’ad Munawir, Eko Andi Suryo, Harimurti Harimurti

    Expansive soil causes road construction damage in the form of cracks or deformations due to changes in moisture content. One method to address this issue is soil stabilization using additive materials. Special additives can sometimes be expensive; hence it is necessary to use additive materials based on industrial waste as a waste management solution to solve the problem of expansive soil as a road construction subgrade. This study aims to analyze the effects of adding two types of industrial waste, namely fly ash (FA) and waste foundry sand (WFS), regarding the microstructure, physical, and mechanical properties of expansive soil. The method of stabilizing expansive soil involves mixing the soil with 9 % FA and various levels of WFS (0 %, 7.5 %, 10 %, 15 %) based on the dry weight of the soil. Microstructure testing includes quantitative X-ray diffraction and scanning electron microscopy. Physical property testing includes specific gravity, Atterberg limits and sieve analysis. Mechanical testing, i.e. compaction, California Bearing Ratio, swelling, and Triaxial tests were conducted. Soil stabilized with 9 % FA and 15 % WFS shows a significant increase in the internal friction angle and cohesion, reducing swelling by 67.18 % compared to the original soil swelling. The addition of 9 % fly ash and 15 % WFS to expansive soil reduces the content of montmorillonite. Natural expansive soils have a very poor soaked CBR of 0.94 %, while stabilized soils with 9 % FA and 15 % WFS have a soaked CBR of 6.46 %. This means that the soaked CBR of the stabilized soil meets the minimum CBR required for road subgrade construction. A mixture of 9 % FA and 15 % WFS in expansive soil can be recommended as a material for stabilizing expansive soil due to its ability to improve microstructure and mechanical properties