Hussein N. Shaman
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Hussein N. Shaman has a total of 43 co-authors. Here are the top co-authors by number of shared publications:
- Kamal Sarabandi
University of Michigan, Ann Arbor, MI, USA
9 shared publications - Constantine A. Balanis
School of Electrical, Computer and Energy Engineering, Arizona State University, Tempe, AZ, USA
7 shared publications - Adib Y. Nashashibi
Department of Electrical Engineering and Computer Science, University of Michigan, Ann Arbor, MI, USA
6 shared publications Craig R. Birtcher
Arizona State University,School of Electrical, Computer and Energy EngineeringTempe,Arizona,USA,85287-5706
4 shared publications- Abdullah Alburadi
Department of Electrical Engineering and Computer Science, University of Michigan, Ann Arbor, MI, USA
3 shared publications - Subramanian Ramalingam
School of Electrical, Computer, and Energy Engineering, Arizona State University, Tempe, AZ 85287, USA
3 shared publications
Latest Publications
- Open Access
- 24 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 14, 30644-30653
Design and Non-Intrusive Diagnostic of High-Gain Wideband Millimeter-Wave Active Antenna Array With Beam-Steering Capability for 5G Application
This paper presents a compact, broadband, beam-steerable antenna array designed for 5G millimeter-wave (mmWave) applications and the use of an electro optical field probe for its performance evaluation. The proposed array consists of 64 elements, arranged as eight-antenna sub-arrays capable of creating a narrow beam and achieving beam steering in horizontal direction. The 1×8 antenna array elements are configured in the vertical direction, and each is controlled by an 8-channel beamformer integrated circuit mounted on the backside, facilitating precise beam steering capabilities. The routing of DC and digital lines have been positioned on the surface of the array to achieve compactness. To improve impedance matching and suppress the grating lobe while steering, two parasitic 1×8 sub-arrays are incorporated into the overall compact design. The antenna array was designed, fabricated and experimentally validated. The proposed structure operates within the frequency range of 24.25 GHz to 29.5 GHz, covering the n257, n258, and n261 bands. Across these bands, the array exhibits a total combined active and passive peak gain of 33.89 dBi. Beam-steering measurement demonstrates that the antenna array can achieve a wide range of beam steering angles of ±45°.
- 24 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 14, 30644-30653
Open AccessDesign and Non-Intrusive Diagnostic of High-Gain Wideband Millimeter-Wave Active Antenna Array With Beam-Steering Capability for 5G Application
This paper presents a compact, broadband, beam-steerable antenna array designed for 5G millimeter-wave (mmWave) applications and the use of an electro optical field probe for its performance evaluation. The proposed array consists of 64 elements, arranged as eight-antenna sub-arrays capable of creating a narrow beam and achieving beam steering in horizontal direction. The 1×8 antenna array elements are configured in the vertical direction, and each is controlled by an 8-channel beamformer integrated circuit mounted on the backside, facilitating precise beam steering capabilities. The routing of DC and digital lines have been positioned on the surface of the array to achieve compactness. To improve impedance matching and suppress the grating lobe while steering, two parasitic 1×8 sub-arrays are incorporated into the overall compact design. The antenna array was designed, fabricated and experimentally validated. The proposed structure operates within the frequency range of 24.25 GHz to 29.5 GHz, covering the n257, n258, and n261 bands. Across these bands, the array exhibits a total combined active and passive peak gain of 33.89 dBi. Beam-steering measurement demonstrates that the antenna array can achieve a wide range of beam steering angles of ±45°.
- Open Access
- 12 February 2026
- Published by Elsevier in Results in Engineering
- Vol. 29
Innovative MIMO antenna for terahertz band 6G communications: Performance evaluation and machine learning integration
- 12 February 2026
- Published by Elsevier in Results in Engineering
- Vol. 29
Open AccessInnovative MIMO antenna for terahertz band 6G communications: Performance evaluation and machine learning integration
- 16 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Radar Systems
- Vol. 4, 309-320
On-Demand Beam-Widening Reflector Antenna for a J-Band Imaging Radar With Micro-Doppler Measurement Capability
In this paper, a novel technique is proposed to widen the beamwidth of a millimeter-wave (MMW) imaging radar system that employs a mechanically scanning elliptic toroidal reflector antenna. For applications requiring Doppler measurements, increased beamwidth enhances Doppler resolution while maintaining scanning speed, enabling improved extraction of micro-Doppler features. The reflector antenna’s beamwidth is widened by employing a feed horn with an adjustable phase center. Relying on the fact that the horn’s phase center is near its aperture, the design incorporates a hollow cylindrical sleeve that extends the aperture forward, thereby shifting the phase center. This phase center displacement de-focuses the reflector and results in a wider radar beam. The design of the feed horn and its electrically actuated sleeve is presented, along with fabrication details. The phase center position of the horn is determined using two experimental techniques. In the first, the horn is placed behind a dielectric lens illuminated by a plane wave, and the phase center is localized by identifying the position that maximizes the received signal power. In the second method, coherent signal measurements on the plane perpendicular to the horn’s boresight are collected using a network analyzer and processed to localize its phase center. In both techniques, the phase center is shown to shift when the sleeve is extended. Beam widening is verified by measuring the reflector’s radiation pattern with the sleeve both extended and retracted, showing good agreement with simulations. A beamwidth increase by a factor of four is demonstrated using a 20 mm sleeve extension. The technique’s effectiveness is further validated through Doppler measurements of a walking person, where Doppler spread is observed using the de-focused beam at scanning speeds of up to 5 cycles per second.
- 16 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Radar Systems
- Vol. 4, 309-320
On-Demand Beam-Widening Reflector Antenna for a J-Band Imaging Radar With Micro-Doppler Measurement Capability
In this paper, a novel technique is proposed to widen the beamwidth of a millimeter-wave (MMW) imaging radar system that employs a mechanically scanning elliptic toroidal reflector antenna. For applications requiring Doppler measurements, increased beamwidth enhances Doppler resolution while maintaining scanning speed, enabling improved extraction of micro-Doppler features. The reflector antenna’s beamwidth is widened by employing a feed horn with an adjustable phase center. Relying on the fact that the horn’s phase center is near its aperture, the design incorporates a hollow cylindrical sleeve that extends the aperture forward, thereby shifting the phase center. This phase center displacement de-focuses the reflector and results in a wider radar beam. The design of the feed horn and its electrically actuated sleeve is presented, along with fabrication details. The phase center position of the horn is determined using two experimental techniques. In the first, the horn is placed behind a dielectric lens illuminated by a plane wave, and the phase center is localized by identifying the position that maximizes the received signal power. In the second method, coherent signal measurements on the plane perpendicular to the horn’s boresight are collected using a network analyzer and processed to localize its phase center. In both techniques, the phase center is shown to shift when the sleeve is extended. Beam widening is verified by measuring the reflector’s radiation pattern with the sleeve both extended and retracted, showing good agreement with simulations. A beamwidth increase by a factor of four is demonstrated using a 20 mm sleeve extension. The technique’s effectiveness is further validated through Doppler measurements of a walking person, where Doppler spread is observed using the de-focused beam at scanning speeds of up to 5 cycles per second.
- Open Access
- 13 October 2025
- Published by Wiley in Engineering Reports
- Vol. 7 (10)
High‐Performance Quad‐Port MIMO Antenna for Next‐Generation Mm‐Wave IoT Application With Efficiency Prediction Using Supervised Regression Methods
Microstrip patch antenna (MPA) single‐element, half‐array, and multiple‐input multiple‐output (MIMO) designs, with an overall MIMO antenna size of 32.02 × 32.02 mm 2 , are built and analyzed in this study. The bandwidth of 4.12 GHz and the band of frequencies 25.605–29.727 GHz are the values used in the simulation. Rogers RT/duroid 5880, a low‐loss dielectric material, is used in the antenna's fabrication. This material has a dielectric constant of 2.2, a tangent loss of 0.0009, and an ultrathin height of 0.8 mm. The analogous model of the proposed MPA is constructed using an advanced design system (ADS) in contrast to the reflection coefficient gained using CST. The return loss of the prototype is also measured and is in contrast to the return loss seen in CST simulations. In the end, 120 data samples are collected through the simulation by using CST MWS, and five machine learning (ML) approaches, such as Nonparametric regression, random forest regression (RFR), decision tree regression (DTR), support vector regression model (SVRM), and extreme gradient boosting (XGB) regression, are implemented to evaluate the efficiency of the patch antenna. Mean square error, mean absolute error, root mean square error, R square, and the variance score are used to assess the efficacy of the five ML models. Nonparametric Regression outperforms the other ML models in terms of prediction accuracy (MSE = 2.31%, MAE = 1.77%, RMSE = 3.33%, R square = 94.28%, and var. score = 95.62%). This article describes analyzing the constructed antenna's performance by a combination of modeling, measurement, building the RLC equivalent circuit model, and incorporating machine learning approaches.
- 13 October 2025
- Published by Wiley in Engineering Reports
- Vol. 7 (10)
Open AccessHigh‐Performance Quad‐Port MIMO Antenna for Next‐Generation Mm‐Wave IoT Application With Efficiency Prediction Using Supervised Regression Methods
Microstrip patch antenna (MPA) single‐element, half‐array, and multiple‐input multiple‐output (MIMO) designs, with an overall MIMO antenna size of 32.02 × 32.02 mm 2 , are built and analyzed in this study. The bandwidth of 4.12 GHz and the band of frequencies 25.605–29.727 GHz are the values used in the simulation. Rogers RT/duroid 5880, a low‐loss dielectric material, is used in the antenna's fabrication. This material has a dielectric constant of 2.2, a tangent loss of 0.0009, and an ultrathin height of 0.8 mm. The analogous model of the proposed MPA is constructed using an advanced design system (ADS) in contrast to the reflection coefficient gained using CST. The return loss of the prototype is also measured and is in contrast to the return loss seen in CST simulations. In the end, 120 data samples are collected through the simulation by using CST MWS, and five machine learning (ML) approaches, such as Nonparametric regression, random forest regression (RFR), decision tree regression (DTR), support vector regression model (SVRM), and extreme gradient boosting (XGB) regression, are implemented to evaluate the efficiency of the patch antenna. Mean square error, mean absolute error, root mean square error, R square, and the variance score are used to assess the efficacy of the five ML models. Nonparametric Regression outperforms the other ML models in terms of prediction accuracy (MSE = 2.31%, MAE = 1.77%, RMSE = 3.33%, R square = 94.28%, and var. score = 95.62%). This article describes analyzing the constructed antenna's performance by a combination of modeling, measurement, building the RLC equivalent circuit model, and incorporating machine learning approaches.
- 24 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Geoscience and Remote Sensing
- Vol. 63 (01962892) , 1-9
Rapid Indoor Mapping and Non-Line-of-Sight Imaging Using a 228-GHz FMCW Polarimetric Radar System
In this article, a polarimetric millimeter-wave FMCW radar operating in the 222-228 GHz frequency range is proposed for mapping applications in indoor environments. Equipped with a mechanically scanning fan-beam reflector antenna with 360° field of view, the radar can generate 2D images of its scene, offering LiDAR-like azimuthal resolution of 0.3°. The system’s performance for indoor mapping as well as Line-of-Sight (LOS) and None-Line-of-Sight (NLOS) obstacle detection tasks is demonstrated in building corridors. The measurement scenarios include various wall types and wooden doors with metallic frames. The overall corridor map is created by taking multiple radar images and combining them through post-processing. Given the strong presence of ghost targets in the radar images, an algorithm is developed for NLOS target detection and localization. As a foundation for this investigation, the wave reflection coefficients of painted drywall for both vertical and horizontal polarizations, ΓVV and ΓHH, are measured. Based on these results, a novel technique for NLOS target identification using polarization discrimination is proposed and experimentally verified. This technique is further tested in a realistic scene, where an L-shaped corridor is mapped using the polarimetric radar measurement, and NLOS targets are detected and localized using a mirroring transformation.
- 24 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Geoscience and Remote Sensing
- Vol. 63 (01962892) , 1-9
Rapid Indoor Mapping and Non-Line-of-Sight Imaging Using a 228-GHz FMCW Polarimetric Radar System
In this article, a polarimetric millimeter-wave FMCW radar operating in the 222-228 GHz frequency range is proposed for mapping applications in indoor environments. Equipped with a mechanically scanning fan-beam reflector antenna with 360° field of view, the radar can generate 2D images of its scene, offering LiDAR-like azimuthal resolution of 0.3°. The system’s performance for indoor mapping as well as Line-of-Sight (LOS) and None-Line-of-Sight (NLOS) obstacle detection tasks is demonstrated in building corridors. The measurement scenarios include various wall types and wooden doors with metallic frames. The overall corridor map is created by taking multiple radar images and combining them through post-processing. Given the strong presence of ghost targets in the radar images, an algorithm is developed for NLOS target detection and localization. As a foundation for this investigation, the wave reflection coefficients of painted drywall for both vertical and horizontal polarizations, ΓVV and ΓHH, are measured. Based on these results, a novel technique for NLOS target identification using polarization discrimination is proposed and experimentally verified. This technique is further tested in a realistic scene, where an L-shaped corridor is mapped using the polarimetric radar measurement, and NLOS targets are detected and localized using a mirroring transformation.
- 18 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 73 (4) , 2356-2365
Improved Single Target Calibration Technique for Polarimetric Radars
In this article, an algorithm for calibrating polarimetric radar systems that ensures accurate measurements of complex scattering matrices of point targets in the backscatter direction is presented. In this approach, only a single target, namely, a metallic sphere, is needed as the calibration target, which significantly simplifies the calibration procedure and improves the accuracy. The error model for the polarimetric radar is based on an exact physics-based channel model for radars with dual-channel passive single antennas (Sarabandi and Ulaby, 1990). This article improves upon (Sarabandi and Ulaby, 1990) by allowing the crosstalk distortion matrices for the transmit and receive antennas to be different, thereby enabling polarimetric calibration of monostatic polarimetric radars with different transmit and receive antennas. The closed-form expressions for the calibrated elements of the scattering matrix of the unknown target in terms of the uncalibrated (measured) scattering matrices of both the unknown target and the calibration sphere are derived. The proposed calibration algorithm is validated experimentally using three different polarimetric radar systems operating at $X$ -, $W$ -, and $J$ -bands and using different point targets with known scattering matrices. Excellent agreements between the measurements and the expected theoretical/numerical results are demonstrated.
- 18 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 73 (4) , 2356-2365
Improved Single Target Calibration Technique for Polarimetric Radars
In this article, an algorithm for calibrating polarimetric radar systems that ensures accurate measurements of complex scattering matrices of point targets in the backscatter direction is presented. In this approach, only a single target, namely, a metallic sphere, is needed as the calibration target, which significantly simplifies the calibration procedure and improves the accuracy. The error model for the polarimetric radar is based on an exact physics-based channel model for radars with dual-channel passive single antennas (Sarabandi and Ulaby, 1990). This article improves upon (Sarabandi and Ulaby, 1990) by allowing the crosstalk distortion matrices for the transmit and receive antennas to be different, thereby enabling polarimetric calibration of monostatic polarimetric radars with different transmit and receive antennas. The closed-form expressions for the calibrated elements of the scattering matrix of the unknown target in terms of the uncalibrated (measured) scattering matrices of both the unknown target and the calibration sphere are derived. The proposed calibration algorithm is validated experimentally using three different polarimetric radar systems operating at $X$ -, $W$ -, and $J$ -bands and using different point targets with known scattering matrices. Excellent agreements between the measurements and the expected theoretical/numerical results are demonstrated.
- 9 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Geoscience and Remote Sensing
- Vol. 61 (01962892) , 1-9
A 223-GHz FMCW Imaging Radar With 360° FoV and 0.3° Azimuthal Resolution Enabled by a Rotationally Stable Fan-Beam Reflector
A mechanically scanned high-resolution 2-D imaging radar system with full 360° Field-of-View (FoV) is presented. The system is composed of a multi-function 222-228 GHz frequency modulated continuous wave (FMCW) radar and a moment of inertia optimized 3-D printed offset reflector antenna. The reflector geometry is made from an Elliptic Toroidal surface which is shown to produce a high-gain fan-beam with an 11:1 aspect ratio. The reflector is rotated at speeds up to 10 Hz for high throughput imaging. The wobble generated by the high speed rotation is suppressed by optimizing the mass distribution of the reflector body. It is fabricated in-house using a low-cost table-top Fused Deposition Modelling (FDM) 3-D printer. The reflecting surface is metallized with a silver coated copper paint and processed using simple steps to ensure smoothness and accuracy. The reflector achieves beamwidths of 4.6° in elevation and 0.42° in azimuth, with a peak gain of 38.7 dBi. The 3 dB azimuthal resolution of the radar two-way beam is measured to be 0.3°. The system is tested in real-world scenarios and the resulting images and videos are of unprecedented quality due to the large area of coverage, high resolution, high speed and excellent dynamic range. To the best of our knowledge, this is the first demonstration of a compact radar system that is comparable in resolution, speed and angular coverage to lidars, while offering higher dynamic range and immunity to severe weather and lighting conditions.
- 9 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Geoscience and Remote Sensing
- Vol. 61 (01962892) , 1-9
A 223-GHz FMCW Imaging Radar With 360° FoV and 0.3° Azimuthal Resolution Enabled by a Rotationally Stable Fan-Beam Reflector
A mechanically scanned high-resolution 2-D imaging radar system with full 360° Field-of-View (FoV) is presented. The system is composed of a multi-function 222-228 GHz frequency modulated continuous wave (FMCW) radar and a moment of inertia optimized 3-D printed offset reflector antenna. The reflector geometry is made from an Elliptic Toroidal surface which is shown to produce a high-gain fan-beam with an 11:1 aspect ratio. The reflector is rotated at speeds up to 10 Hz for high throughput imaging. The wobble generated by the high speed rotation is suppressed by optimizing the mass distribution of the reflector body. It is fabricated in-house using a low-cost table-top Fused Deposition Modelling (FDM) 3-D printer. The reflecting surface is metallized with a silver coated copper paint and processed using simple steps to ensure smoothness and accuracy. The reflector achieves beamwidths of 4.6° in elevation and 0.42° in azimuth, with a peak gain of 38.7 dBi. The 3 dB azimuthal resolution of the radar two-way beam is measured to be 0.3°. The system is tested in real-world scenarios and the resulting images and videos are of unprecedented quality due to the large area of coverage, high resolution, high speed and excellent dynamic range. To the best of our knowledge, this is the first demonstration of a compact radar system that is comparable in resolution, speed and angular coverage to lidars, while offering higher dynamic range and immunity to severe weather and lighting conditions.
- Open Access
- 5 June 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (11) , 6834
Parallel-Coupled-Line Bandpass Filter with Notch for Ultra-Wideband (UWB) Applications
A compact parallel-coupled-line microstrip bandpass filter with a very wideband passband and a narrow notched band is demonstrated in this paper. The presented bandpass filter was constructed from one section of three parallel-coupled-lines which has a length of a quarter wavelength at a midband frequency of 6.9 GHz. For the purpose of increasing the filter selectivity, the middle line is extended by a length of a quarter-wavelength and connected at one end to the ground plane. Therefore, a transmission zero was generated at each side of the passband which effectively improved the filter performance. In addition, a narrow notched band at a precise frequency inside the proposed passband was exhibited by placing a stepped-impedance resonator near the parallel-coupled-line for blocking the unwanted radio signal. The proposed filter was designed, simulated, fabricated, and measured. The fabricated filter has a very compact circuit size and its measured response shows an excellent agreement with the simulated results.
- 5 June 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (11) , 6834
Open AccessParallel-Coupled-Line Bandpass Filter with Notch for Ultra-Wideband (UWB) Applications
A compact parallel-coupled-line microstrip bandpass filter with a very wideband passband and a narrow notched band is demonstrated in this paper. The presented bandpass filter was constructed from one section of three parallel-coupled-lines which has a length of a quarter wavelength at a midband frequency of 6.9 GHz. For the purpose of increasing the filter selectivity, the middle line is extended by a length of a quarter-wavelength and connected at one end to the ground plane. Therefore, a transmission zero was generated at each side of the passband which effectively improved the filter performance. In addition, a narrow notched band at a precise frequency inside the proposed passband was exhibited by placing a stepped-impedance resonator near the parallel-coupled-line for blocking the unwanted radio signal. The proposed filter was designed, simulated, fabricated, and measured. The fabricated filter has a very compact circuit size and its measured response shows an excellent agreement with the simulated results.
- 23 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Geoscience and Remote Sensing Letters
- Vol. 19 (1545598X) , 1-5
A Method for Signal Leakage Cancellation in Multistatic Subsurface SAR Imaging System
Multistatic subsurface synthetic aperture radar (SAR) is a promising tool capable of providing 3-D high-resolution images of targets buried underground. The high detection capability of the system stems from the fact that the multistatic configuration allows for viewing the targets from many directions. However, a primal limiting factor for such configuration is the dominance of the direct and ground reflection signals over the scattered target signal hindering the system sensitivity. This letter presents a simple technique to overcome such drawbacks. By an appropriate utilization of SAR data, each adjacent sampling point is coprocessed together as a two-element array in such a way as to have a null along the direction of the direct and ground reflection signals suppressing such signals and making the target signals more discernible. The technique is described in detail, and the potential problems arising from array processing are discussed. Additionally, a modified version of the back-projection (BP) imaging algorithm suitable for the array is provided. The performance of the proposed technique is assessed by simulation data of buried metallic spheres as well as measurement data for a buried metallic pipeline. Both simulation and measurements show a significant improvement in target detection and image quality.
- 23 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Geoscience and Remote Sensing Letters
- Vol. 19 (1545598X) , 1-5
A Method for Signal Leakage Cancellation in Multistatic Subsurface SAR Imaging System
Multistatic subsurface synthetic aperture radar (SAR) is a promising tool capable of providing 3-D high-resolution images of targets buried underground. The high detection capability of the system stems from the fact that the multistatic configuration allows for viewing the targets from many directions. However, a primal limiting factor for such configuration is the dominance of the direct and ground reflection signals over the scattered target signal hindering the system sensitivity. This letter presents a simple technique to overcome such drawbacks. By an appropriate utilization of SAR data, each adjacent sampling point is coprocessed together as a two-element array in such a way as to have a null along the direction of the direct and ground reflection signals suppressing such signals and making the target signals more discernible. The technique is described in detail, and the potential problems arising from array processing are discussed. Additionally, a modified version of the back-projection (BP) imaging algorithm suitable for the array is provided. The performance of the proposed technique is assessed by simulation data of buried metallic spheres as well as measurement data for a buried metallic pipeline. Both simulation and measurements show a significant improvement in target detection and image quality.
- 10 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Terahertz Science and Technology
- Vol. 11 (5) , 508-518
Sub-Millimeter-Wave Polarization-Independent Spatial Power Divider for a Two-Port Dual-Polarized Antenna
An antenna system is proposed that uses a novel polarization-independent spatial power divider to align the beams from two orthogonally oriented dual-polarized feeds. This antenna system uses a common aperture for transmitting and receiving and provides high port isolation while maintaining compatibility with fully polarimetric radar. Unlike conventional two antenna radar systems, a radar using this antenna does not suffer from the parallax problem. The spatial power divider is designed using an all-dielectric metasurface approach and is fabricated on a silicon wafer using standard micromachining technology. The measured device exhibits at most 0.9 dB of difference between the reflection and transmission for both transverse electric and transverse magnetic incident waves at 45° incidence, over a band from 221 to 250 GHz. Conical horns are fabricated as feeds and together with the spatial power divider, a focusing lens, and microwave absorbers, are assembled in a three-dimensional-printed housing to complete the antenna system. Its measured gain is approximately 39 dB for each port and polarization, and isolation between ports is at least 40 dB for all polarization combinations over the band of interest.
- 10 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Terahertz Science and Technology
- Vol. 11 (5) , 508-518
Sub-Millimeter-Wave Polarization-Independent Spatial Power Divider for a Two-Port Dual-Polarized Antenna
An antenna system is proposed that uses a novel polarization-independent spatial power divider to align the beams from two orthogonally oriented dual-polarized feeds. This antenna system uses a common aperture for transmitting and receiving and provides high port isolation while maintaining compatibility with fully polarimetric radar. Unlike conventional two antenna radar systems, a radar using this antenna does not suffer from the parallax problem. The spatial power divider is designed using an all-dielectric metasurface approach and is fabricated on a silicon wafer using standard micromachining technology. The measured device exhibits at most 0.9 dB of difference between the reflection and transmission for both transverse electric and transverse magnetic incident waves at 45° incidence, over a band from 221 to 250 GHz. Conical horns are fabricated as feeds and together with the spatial power divider, a focusing lens, and microwave absorbers, are assembled in a three-dimensional-printed housing to complete the antenna system. Its measured gain is approximately 39 dB for each port and polarization, and isolation between ports is at least 40 dB for all polarization combinations over the band of interest.