Christian Seidel
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Christian Seidel has a total of 84 co-authors. Here are the top co-authors by number of shared publications:
- Björn Ringel
Fraunhofer Institute for Casting, Composite and Processing Technology IGCV, Augsburg, Germany
4 shared publications - Georg Schlick
Fraunhofer Institute for Casting, Composite and Processing Technology IGCV, Augsburg, Germany
3 shared publications Gunther Reinhart
Fraunhofer Research Institution for Casting, Composite and Processing Technology IGCV
3 shared publications- Hoang Minh Vu
Technical University of Darmstadt, Darmstadt, Germany
3 shared publications M.F. Zaeh
3 shared publications- Matthias Oechsner
Technical University of Darmstadt, Darmstadt, Germany
3 shared publications
Latest Publications
- 1 December 2025
- Published by World Scientific Pub Co Pte Ltd in Nano Micro Mechanics Review
- Vol. 01 (03) , 163-170
Capability of multi-material powder bed fusion: Design, manufacturing, and validation of a smart injection molding tool
Powder Bed Fusion of metals using a Laser Beam (PBF-LB/M) offers unique possibilities to manufacture functionally graded materials composed of different alloys, enabling the creation of multi-material parts with material properties tailored to specific local requirements. In injection molding, optimized heat transfer and temperature control are key to the quality and productivity of the process. Combining a material with excellent thermal conductivity with a material with mechanical strength can be beneficial to improve the injection molding process. This work investigated the merits of an optimized copper structure in a multi-material injection molding tool while measuring its performance with integrated sensors. The sensor data were compared to data from a mono-material reference part. By incorporating a specifically designed copper geometry optimized for heat dissipation without compromising the stiffness of the tool, a reduction of the cycle time by 19% was achieved.
- 1 December 2025
- Published by World Scientific Pub Co Pte Ltd in Nano Micro Mechanics Review
- Vol. 01 (03) , 163-170
Capability of multi-material powder bed fusion: Design, manufacturing, and validation of a smart injection molding tool
Powder Bed Fusion of metals using a Laser Beam (PBF-LB/M) offers unique possibilities to manufacture functionally graded materials composed of different alloys, enabling the creation of multi-material parts with material properties tailored to specific local requirements. In injection molding, optimized heat transfer and temperature control are key to the quality and productivity of the process. Combining a material with excellent thermal conductivity with a material with mechanical strength can be beneficial to improve the injection molding process. This work investigated the merits of an optimized copper structure in a multi-material injection molding tool while measuring its performance with integrated sensors. The sensor data were compared to data from a mono-material reference part. By incorporating a specifically designed copper geometry optimized for heat dissipation without compromising the stiffness of the tool, a reduction of the cycle time by 19% was achieved.
- Open Access
- 8 May 2024
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 10 (1) , 997
Correction: Investigation on a predetermined point of failure for stainless steel 316L pressure loaded components made by laser powder bed fusion through stress analysis and experimental testing
- 8 May 2024
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 10 (1) , 997
Open AccessCorrection: Investigation on a predetermined point of failure for stainless steel 316L pressure loaded components made by laser powder bed fusion through stress analysis and experimental testing
- Open Access
- 29 April 2024
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 10 (1) , 999
Correction: Investigation on a predetermined point of failure for stainless steel 316L pressure loaded components made by laser powder bed fusion through stress analysis and experimental testing
- 29 April 2024
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 10 (1) , 999
Open AccessCorrection: Investigation on a predetermined point of failure for stainless steel 316L pressure loaded components made by laser powder bed fusion through stress analysis and experimental testing
- Open Access
- 13 February 2024
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 9 (6) , 2041-2060
Investigation on surface characteristics of wall structures out of stainless steel 316L manufactured by laser powder bed fusion
Pressure equipment poses a high risk of harming people and the environment in case of failure. They are, therefore, highly regulated by the Pressure Equipment Directive. To enable laser powder bed fusion of metals (PBF-LB/M) for the manufacturing of such components, component appearance and quality need to be characterized and qualified for each specific system. In this study, the surface roughness of wall structures out of austenitic stainless steel (316L) is investigated. Wall structure specimens were produced by four manufacturing systems on different PBF-LB/M machines and with different powder materials. Surface roughness of specimens are compared in the upskin and downskin areas in relation to different slope angles and wall thicknesses. Although different process setups, parameters and powder feedstocks have been used, similarities in the dependency of the surface roughness related to the slope angle and wall thickness can be observed. This work furthermore presents a mechanism-based analytical approach to predict system-specific surface roughness. Particularly, the analytical approach on the influence of slope angle on the surface roughness of the downskin areas has not been covered in publications about PBF-LB/M before. The results of this work enable the prediction of system-specific surface roughness, which is especially important for parts with downskin areas and hidden surfaces without the possibility of additional surface treatment.
- 13 February 2024
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 9 (6) , 2041-2060
Open AccessInvestigation on surface characteristics of wall structures out of stainless steel 316L manufactured by laser powder bed fusion
Pressure equipment poses a high risk of harming people and the environment in case of failure. They are, therefore, highly regulated by the Pressure Equipment Directive. To enable laser powder bed fusion of metals (PBF-LB/M) for the manufacturing of such components, component appearance and quality need to be characterized and qualified for each specific system. In this study, the surface roughness of wall structures out of austenitic stainless steel (316L) is investigated. Wall structure specimens were produced by four manufacturing systems on different PBF-LB/M machines and with different powder materials. Surface roughness of specimens are compared in the upskin and downskin areas in relation to different slope angles and wall thicknesses. Although different process setups, parameters and powder feedstocks have been used, similarities in the dependency of the surface roughness related to the slope angle and wall thickness can be observed. This work furthermore presents a mechanism-based analytical approach to predict system-specific surface roughness. Particularly, the analytical approach on the influence of slope angle on the surface roughness of the downskin areas has not been covered in publications about PBF-LB/M before. The results of this work enable the prediction of system-specific surface roughness, which is especially important for parts with downskin areas and hidden surfaces without the possibility of additional surface treatment.
- Open Access
- 20 June 2023
- Published by SciCell in Acta Metallurgica Slovaca
- Vol. 29 (2) , 82-87
CHANGE IN MICROSTRUCTURE AND HARDNESS OF ADDITIVELY MANUFACTURED AISI H13 STEEL BY HEAT TREATMENT AND NITRIDING PROCESSES
AISI H13 steel samples were additively manufactured using a laser powder bed fusion (LPBF) system. The effect of annealing tem-perature, quenching & tempering, and nitriding were determined. The microstructure and properties of the samples were investigated using optical microscopy, scanning electron microscopy, electron backscattered diffraction, electron probe micro-analysis, X-ray diffraction, roughness measurement, and a hardness tester. The results show that the as-built AISI H13 steel sample had a roughness on the surface and pores inside. The microstructure consisted of martensite and retained austenite. The average hardness was 460 HV, and the porosity was 0.086 %. The annealing process helped homogenize the microstructure, increase the density, and reduce the porosity and hardness of the LPBF-manufactured sample. The quenching process helped increase the hardness of the steel to the maximum of 787 HV, then the tempering process reduced the hardness to 572 HV. Heat treatment and nitriding processes tended to increase the martensite block size, reduce the retained austenitic content, and precipitate the V-Mo-rich carbide in the LPBF-manufactured AISI H13 steel. After nitriding was conducted, the nitriding case depth was 87 um, and the surface hardness increased up to higher than 1020 HV due to the formation of CrN and Fe3-4N.
- 20 June 2023
- Published by SciCell in Acta Metallurgica Slovaca
- Vol. 29 (2) , 82-87
Open AccessCHANGE IN MICROSTRUCTURE AND HARDNESS OF ADDITIVELY MANUFACTURED AISI H13 STEEL BY HEAT TREATMENT AND NITRIDING PROCESSES
AISI H13 steel samples were additively manufactured using a laser powder bed fusion (LPBF) system. The effect of annealing tem-perature, quenching & tempering, and nitriding were determined. The microstructure and properties of the samples were investigated using optical microscopy, scanning electron microscopy, electron backscattered diffraction, electron probe micro-analysis, X-ray diffraction, roughness measurement, and a hardness tester. The results show that the as-built AISI H13 steel sample had a roughness on the surface and pores inside. The microstructure consisted of martensite and retained austenite. The average hardness was 460 HV, and the porosity was 0.086 %. The annealing process helped homogenize the microstructure, increase the density, and reduce the porosity and hardness of the LPBF-manufactured sample. The quenching process helped increase the hardness of the steel to the maximum of 787 HV, then the tempering process reduced the hardness to 572 HV. Heat treatment and nitriding processes tended to increase the martensite block size, reduce the retained austenitic content, and precipitate the V-Mo-rich carbide in the LPBF-manufactured AISI H13 steel. After nitriding was conducted, the nitriding case depth was 87 um, and the surface hardness increased up to higher than 1020 HV due to the formation of CrN and Fe3-4N.
- Open Access
- 28 March 2023
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 8 (5) , 773-774
Standardisation efforts of ISO/TC 261 “additive manufacturing” 20th plenary meeting of ISO/TC 261 “additive manufacturing”
The main objective of ISO/TC 261 is to standardise the processes of additive manufacturing, the process chains (Data, Materials, Processes, Hard- and Software, Applications), test procedures, quality parameters, supply agreements, environment, health and safety, fundamentals and vocabularies. This section provides readers with news regarding standardisation efforts of ISO/TC 261. Further up-to-date information regarding recently published documents, such as new standards and revised standards, the status of standards can be found in the ISO/TC261 webpages: https://www.iso.org/committee/629086.html and the committee webpages: https://committee.iso.org/sites/tc261/home/news.html.
- 28 March 2023
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 8 (5) , 773-774
Open AccessStandardisation efforts of ISO/TC 261 “additive manufacturing” 20th plenary meeting of ISO/TC 261 “additive manufacturing”
The main objective of ISO/TC 261 is to standardise the processes of additive manufacturing, the process chains (Data, Materials, Processes, Hard- and Software, Applications), test procedures, quality parameters, supply agreements, environment, health and safety, fundamentals and vocabularies. This section provides readers with news regarding standardisation efforts of ISO/TC 261. Further up-to-date information regarding recently published documents, such as new standards and revised standards, the status of standards can be found in the ISO/TC261 webpages: https://www.iso.org/committee/629086.html and the committee webpages: https://committee.iso.org/sites/tc261/home/news.html.
- Open Access
- 28 March 2022
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 7 (5) , 1123-1124
Standardisation efforts of ISO/TC 261 “Additive Manufacturing”: 18th Plenary Meeting of ISO/TC 261 “Additive Manufacturing”
- 28 March 2022
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 7 (5) , 1123-1124
Open AccessStandardisation efforts of ISO/TC 261 “Additive Manufacturing”: 18th Plenary Meeting of ISO/TC 261 “Additive Manufacturing”
- 1 January 2022
- Published by Springer Nature
- p. 207-214
Synergien bei der Umsetzung von WRRL und FFH Richtlinie
- 1 January 2022
- Published by Springer Nature
- p. 207-214
Synergien bei der Umsetzung von WRRL und FFH Richtlinie
- Open Access
Capability of Multi-Material Laser-Based Powder Bed Fusion—Development and Analysis of a Prototype Large Bore Engine Component
Additive Manufacturing (AM) allows the manufacturing of functionally graded materials (FGM). This includes compositional grading, which enables the allocation of desired materials corresponding to local product requirements. An upcoming AM process for the creation of metal-based FGMs is laser-based powder bed fusion (PBF-LB/M) utilized for multi-material manufacturing (MM). Three-dimensional multi-material approaches for PBF-LB/M are stated to have a manufacturing readiness level (MRL) of 4 to 5. In this paper, an advancement of multi-material technology is presented by realizing an industry-relevant complex part as a prototype made by PBF-LB/M. Hence, a multi-material injection nozzle consisting of tool steel and a copper alloy was manufactured in a continuous PBF-LB/M process. Single material regions showed qualities similar to the ones resulting from mono-material processes. A geometrically defined transition zone between the two materials was achieved that showed slightly higher porosity than mono-material regions. Nevertheless, defects such as porosity, cracks, and material cross-contamination were detected and must be overcome in further MM technology development.
Open AccessCapability of Multi-Material Laser-Based Powder Bed Fusion—Development and Analysis of a Prototype Large Bore Engine Component
Additive Manufacturing (AM) allows the manufacturing of functionally graded materials (FGM). This includes compositional grading, which enables the allocation of desired materials corresponding to local product requirements. An upcoming AM process for the creation of metal-based FGMs is laser-based powder bed fusion (PBF-LB/M) utilized for multi-material manufacturing (MM). Three-dimensional multi-material approaches for PBF-LB/M are stated to have a manufacturing readiness level (MRL) of 4 to 5. In this paper, an advancement of multi-material technology is presented by realizing an industry-relevant complex part as a prototype made by PBF-LB/M. Hence, a multi-material injection nozzle consisting of tool steel and a copper alloy was manufactured in a continuous PBF-LB/M process. Single material regions showed qualities similar to the ones resulting from mono-material processes. A geometrically defined transition zone between the two materials was achieved that showed slightly higher porosity than mono-material regions. Nevertheless, defects such as porosity, cracks, and material cross-contamination were detected and must be overcome in further MM technology development.