Nuno Monteiro Azevedo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Nuno Monteiro Azevedo has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
- Maria Luísa Braga Farinha
Concrete Dams Department, National Laboratory for Civil Engineering (LNEC), 1700-066 Lisboa, Portugal
13 shared publications - Sérgio Oliveira
Concrete Dams Department, National Laboratory for Civil Engineering (LNEC), Av. do Brasil 101, 1700-075 Lisboa, Portugal
8 shared publications - José Vieira Lemos
National Laboratory for Civil Engineering (LNEC)
7 shared publications - Rui Micaelo
CERIS, Department of Civil Engineering, NOVA School of Science and Technology, Universidade NOVA de Lisboa, 2829-516 Caparica, Portugal
7 shared publications - Gustavo Câmara
LNEC—National Laboratory for Civil Engineering, 1700-066 Lisbon, Portugal
6 shared publications - António Lopes Batista
National Laboratory for Civil Engineering
5 shared publications
Latest Publications
- Open Access
- 1 April 2026
- Published by MDPI AG in Infrastructures
- Vol. 11 (4) , 122
Stability Analysis of Concrete Dam Foundations Using a Particle/Surface Interface Model for Large Displacements
In concrete dam foundations, failure mechanisms are primarily influenced by natural rock discontinuities, the dam foundation interface, or weaker strata. This paper proposes a large displacement contact model (LDCM) based on spherical particle/surface interactions, which is computationally more robust and simpler than contact models that adopt the real block polyhedral geometry. To reduce computational costs, whenever possible, the contact interaction is defined in small displacements. The proposed LDCM is applied to a masonry arch under static loading and to the stability analysis of both a gravity dam and an arch dam. The results presented validate the proposed LDCM, and the numerical predictions are close to results obtained experimentally and closely match those obtained with a more complex polyhedral-based model. The advantages of the LDCM are highlighted, namely the decoupling of contact refinement from block refinement, which significantly reduces the computational costs for the masonry arch example. The relevance of adopting a LDCM to predict a physically accepted failure mode is emphasized for dam safety. Finaly, it is shown that the LDCM contact model can be readily adopted to assess the stability of complex dam foundation systems, with reasonable computational running times if a hybrid contact approach is used.
- 1 April 2026
- Published by MDPI AG in Infrastructures
- Vol. 11 (4) , 122
Open AccessStability Analysis of Concrete Dam Foundations Using a Particle/Surface Interface Model for Large Displacements
In concrete dam foundations, failure mechanisms are primarily influenced by natural rock discontinuities, the dam foundation interface, or weaker strata. This paper proposes a large displacement contact model (LDCM) based on spherical particle/surface interactions, which is computationally more robust and simpler than contact models that adopt the real block polyhedral geometry. To reduce computational costs, whenever possible, the contact interaction is defined in small displacements. The proposed LDCM is applied to a masonry arch under static loading and to the stability analysis of both a gravity dam and an arch dam. The results presented validate the proposed LDCM, and the numerical predictions are close to results obtained experimentally and closely match those obtained with a more complex polyhedral-based model. The advantages of the LDCM are highlighted, namely the decoupling of contact refinement from block refinement, which significantly reduces the computational costs for the masonry arch example. The relevance of adopting a LDCM to predict a physically accepted failure mode is emphasized for dam safety. Finaly, it is shown that the LDCM contact model can be readily adopted to assess the stability of complex dam foundation systems, with reasonable computational running times if a hybrid contact approach is used.
- Open Access
- 15 January 2026
- Published by MDPI AG in Applied Mechanics
- Vol. 7 (1) , 8
Effects of Geometry, Joint Properties, and Deterioration Scenarios on the Hydromechanical Response of Gravity Dams
An explicit coupled two-dimensional (2D) hydromechanical model (HMM) that can simulate discontinuous features in the foundation, as well as the effects of grout curtains and drainage systems, is employed to evaluate the influence of key parameters such as dam height, foundation behaviour, joint patterns, joint stiffness and strength, hydraulic apertures, and grout curtain permeability. A parametric sensitive study using four gravity dams, and a real case study of an operating dam are presented. The results presented show that dam height influences the relationship between water level in the reservoir and drain discharges, with higher dams showing more pronounced curved nonlinearity. The strength properties of the concrete–rock interface are also shown to have a meaningful influence on the HM response, especially for an elastic foundation and for higher dams, showing the need to properly characterize this interface through in situ testing. The joint aperture at nominal zero stress is shown to be the parameter with the most significant effect on the HM response. The results also show that a progressive degradation scenario of the concrete–rock interface or of the grout curtain permeability is easier to identify through the hydraulic measurements than in the mechanical displacement field.
- 15 January 2026
- Published by MDPI AG in Applied Mechanics
- Vol. 7 (1) , 8
Open AccessEffects of Geometry, Joint Properties, and Deterioration Scenarios on the Hydromechanical Response of Gravity Dams
An explicit coupled two-dimensional (2D) hydromechanical model (HMM) that can simulate discontinuous features in the foundation, as well as the effects of grout curtains and drainage systems, is employed to evaluate the influence of key parameters such as dam height, foundation behaviour, joint patterns, joint stiffness and strength, hydraulic apertures, and grout curtain permeability. A parametric sensitive study using four gravity dams, and a real case study of an operating dam are presented. The results presented show that dam height influences the relationship between water level in the reservoir and drain discharges, with higher dams showing more pronounced curved nonlinearity. The strength properties of the concrete–rock interface are also shown to have a meaningful influence on the HM response, especially for an elastic foundation and for higher dams, showing the need to properly characterize this interface through in situ testing. The joint aperture at nominal zero stress is shown to be the parameter with the most significant effect on the HM response. The results also show that a progressive degradation scenario of the concrete–rock interface or of the grout curtain permeability is easier to identify through the hydraulic measurements than in the mechanical displacement field.
- Open Access
- 28 October 2025
- Published by ABMS - Brazilian Association for Soil Mechanics and Geotechnical Engineering in Soils and Rocks
- Vol. 48 (4)
A coupled hydromechanical model including fracture propagation along the dam foundation interface for gravity dam’s stability assessment
Most gravity dam failures occur due to sliding along the dam/foundation interface, rock mass discontinuities, or rock mass layers of lower strength. The possibility of sliding of a dam is usually evaluated based on simplified limit equilibrium techniques. In this study an explicit time-stepping small displacement algorithm, Parmac2D-Fflow, is used to assess the safety of gravity dams. This algorithm is based on a discrete representation of discontinuities, simulates the hydromechanical interaction, and considers softening constitutive laws that are closer to the actual behaviour of the dam/foundation interface. Seepage flow along the dam/foundation interface is only allowed to occur after contact failure, making it possible to model a coupled propagation failure along the dam/foundation interface due to a hypothetical dam overtopping scenario. For two gravity dams with different heights, the numerical results predicted with a coupled/fracture propagation model are compared with those obtained with a coupled/fully fractured model and with an uncoupled analysis. The results presented highlight the relevance of considering a coupled hydro-mechanical model for dam safety analysis and show that with a coupled-fracture propagation model slightly higher safety factors are predicted.
- 28 October 2025
- Published by ABMS - Brazilian Association for Soil Mechanics and Geotechnical Engineering in Soils and Rocks
- Vol. 48 (4)
Open AccessA coupled hydromechanical model including fracture propagation along the dam foundation interface for gravity dam’s stability assessment
Most gravity dam failures occur due to sliding along the dam/foundation interface, rock mass discontinuities, or rock mass layers of lower strength. The possibility of sliding of a dam is usually evaluated based on simplified limit equilibrium techniques. In this study an explicit time-stepping small displacement algorithm, Parmac2D-Fflow, is used to assess the safety of gravity dams. This algorithm is based on a discrete representation of discontinuities, simulates the hydromechanical interaction, and considers softening constitutive laws that are closer to the actual behaviour of the dam/foundation interface. Seepage flow along the dam/foundation interface is only allowed to occur after contact failure, making it possible to model a coupled propagation failure along the dam/foundation interface due to a hypothetical dam overtopping scenario. For two gravity dams with different heights, the numerical results predicted with a coupled/fracture propagation model are compared with those obtained with a coupled/fully fractured model and with an uncoupled analysis. The results presented highlight the relevance of considering a coupled hydro-mechanical model for dam safety analysis and show that with a coupled-fracture propagation model slightly higher safety factors are predicted.
- Open Access
- 19 August 2025
- Published by MDPI AG in Sustainability
- Vol. 17 (16) , 7502
Self-Healing Asphalt Mixtures Meso-Modelling: Impact of Capsule Content on Stiffness and Tensile Strength
Capsule-based self-healing technologies offer a promising solution to extend pavement service life without requiring external activation. The effect of the capsule content on the mechanical behaviour of self-healing asphalt mixtures still needs to be understood. This study presents a numerical evaluation of the isolated effect of incorporating capsules containing encapsulated rejuvenators, at different volume contents, on the stiffness and strength of asphalt mixtures through a three-dimensional discrete-based programme (VirtualPM3DLab), which has been shown to predict well the experimental behaviour of asphalt mixtures. Uniaxial tension–compression cyclic and monotonic tensile tests on notched specimens are carried out for three capsule contents commonly adopted in experimental investigations (0.30, 0.75, and 1.25 wt.%). The results show that the effect on the stiffness modulus progressively increases as the capsule content grows in the asphalt mixture, with a reduction ranging from 4.3% to 12.3%. At the same time, the phase angle is marginally affected. The capsule continuum equivalent Young’s modulus has minimum influence on the overall rheological response, suggesting that the most critical parameter affecting asphalt mixture stiffness is the capsule content. Finally, while the peak tensile strength shows a maximum reduction of 12.4% at the highest capsule content, the stress–strain behaviour and damage evolution of the specimens remain largely unaffected. Most damaged contacts, which mainly include aggregate–mastic and mastic–mastic contacts, are highly localised around the notch tips. Contacts involving capsules remained intact during early and intermediate loading stages and only fractured during the final damage stage, suggesting a delayed activation consistent with the design of healing systems. The findings suggest that capsules within the studied contents may have a moderate impact on the mechanical properties of asphalt mixtures, especially for high-volume contents. For this reason, contents higher than 0.75 wt.% should be applied with caution.
- 19 August 2025
- Published by MDPI AG in Sustainability
- Vol. 17 (16) , 7502
Open AccessSelf-Healing Asphalt Mixtures Meso-Modelling: Impact of Capsule Content on Stiffness and Tensile Strength
Capsule-based self-healing technologies offer a promising solution to extend pavement service life without requiring external activation. The effect of the capsule content on the mechanical behaviour of self-healing asphalt mixtures still needs to be understood. This study presents a numerical evaluation of the isolated effect of incorporating capsules containing encapsulated rejuvenators, at different volume contents, on the stiffness and strength of asphalt mixtures through a three-dimensional discrete-based programme (VirtualPM3DLab), which has been shown to predict well the experimental behaviour of asphalt mixtures. Uniaxial tension–compression cyclic and monotonic tensile tests on notched specimens are carried out for three capsule contents commonly adopted in experimental investigations (0.30, 0.75, and 1.25 wt.%). The results show that the effect on the stiffness modulus progressively increases as the capsule content grows in the asphalt mixture, with a reduction ranging from 4.3% to 12.3%. At the same time, the phase angle is marginally affected. The capsule continuum equivalent Young’s modulus has minimum influence on the overall rheological response, suggesting that the most critical parameter affecting asphalt mixture stiffness is the capsule content. Finally, while the peak tensile strength shows a maximum reduction of 12.4% at the highest capsule content, the stress–strain behaviour and damage evolution of the specimens remain largely unaffected. Most damaged contacts, which mainly include aggregate–mastic and mastic–mastic contacts, are highly localised around the notch tips. Contacts involving capsules remained intact during early and intermediate loading stages and only fractured during the final damage stage, suggesting a delayed activation consistent with the design of healing systems. The findings suggest that capsules within the studied contents may have a moderate impact on the mechanical properties of asphalt mixtures, especially for high-volume contents. For this reason, contents higher than 0.75 wt.% should be applied with caution.
- Open Access
- 15 April 2025
- Published by MDPI AG in Geosciences
- Vol. 15 (4) , 149
Safety Assessment of Concrete Gravity Dams: Hydromechanical Coupling and Fracture Propagation
For the safety assessment of concrete dam–foundation systems, this study used an explicit time-stepping small-displacement algorithm, which simulates the hydromechanical interaction and considers the discrete representation of the foundation discontinuities. The proposed innovative methodology allows for the definition of more reliable safety factors and the identification of more realistic failure modes by integrating (i) softening-based constitutive laws that are closer to the real behavior identified experimentally in concrete–concrete and concrete–rock interfaces; (ii) a water height increase that can be considered in both hydraulic and mechanical models; and (iii) fracture propagation along the dam–foundation interface. Parametric studies were conducted to assess the impact of the mechanical properties on the global safety factors of three gravity dams with different heights. The results obtained using a coupled/fracture propagation model were compared with those from the strength reduction method and the overtopping scenario not considering the hydraulic pressure increase. The results show that the safety assessment should be conducted using the proposed methodology. It is shown that the concrete–rock interface should preferably have a high value of fracture energy or, ideally, higher tensile and cohesion strengths and high associated fracture energy. The results also indicate that with a brittle concrete–rock model, the predicted safety factors are always conservative when compared with those that consider the fracture energy.
- 15 April 2025
- Published by MDPI AG in Geosciences
- Vol. 15 (4) , 149
Open AccessSafety Assessment of Concrete Gravity Dams: Hydromechanical Coupling and Fracture Propagation
For the safety assessment of concrete dam–foundation systems, this study used an explicit time-stepping small-displacement algorithm, which simulates the hydromechanical interaction and considers the discrete representation of the foundation discontinuities. The proposed innovative methodology allows for the definition of more reliable safety factors and the identification of more realistic failure modes by integrating (i) softening-based constitutive laws that are closer to the real behavior identified experimentally in concrete–concrete and concrete–rock interfaces; (ii) a water height increase that can be considered in both hydraulic and mechanical models; and (iii) fracture propagation along the dam–foundation interface. Parametric studies were conducted to assess the impact of the mechanical properties on the global safety factors of three gravity dams with different heights. The results obtained using a coupled/fracture propagation model were compared with those from the strength reduction method and the overtopping scenario not considering the hydraulic pressure increase. The results show that the safety assessment should be conducted using the proposed methodology. It is shown that the concrete–rock interface should preferably have a high value of fracture energy or, ideally, higher tensile and cohesion strengths and high associated fracture energy. The results also indicate that with a brittle concrete–rock model, the predicted safety factors are always conservative when compared with those that consider the fracture energy.
- Open Access
Numerical Modeling of Reinforcement Solutions in Traditional Stone Masonry Using a Particle Model
Traditional stone masonry walls are structural elements in most historic buildings. To preserve them and improve their ability to withstand extreme events, such as earthquakes, it is necessary to implement effective reinforcement solutions. This paper presents the modeling of traditional Portuguese rubble stone masonry walls, reinforced with external steel mesh, sprayed micro-concrete layers and transverse confinement by steel connectors, which were developed and tested experimentally in uniaxial compression. The modeling is carried out using micro-modeling through a 2D particle model (PM). The process of calibrating the properties of both micro-concrete and concrete is presented, the methodology for generating the numerical models is described and the numerical response is compared with the experimental results. The numerical results show that the PM can adequately reproduce the experimentally observed behavior of this type of reinforcement solution.
Open AccessNumerical Modeling of Reinforcement Solutions in Traditional Stone Masonry Using a Particle Model
Traditional stone masonry walls are structural elements in most historic buildings. To preserve them and improve their ability to withstand extreme events, such as earthquakes, it is necessary to implement effective reinforcement solutions. This paper presents the modeling of traditional Portuguese rubble stone masonry walls, reinforced with external steel mesh, sprayed micro-concrete layers and transverse confinement by steel connectors, which were developed and tested experimentally in uniaxial compression. The modeling is carried out using micro-modeling through a 2D particle model (PM). The process of calibrating the properties of both micro-concrete and concrete is presented, the methodology for generating the numerical models is described and the numerical response is compared with the experimental results. The numerical results show that the PM can adequately reproduce the experimentally observed behavior of this type of reinforcement solution.
- Open Access
- 5 January 2025
- Published by MDPI AG in Applied Mechanics
- Vol. 6 (1) , 2
A Novel 3D Reinforced Particle Model for Reinforced Concrete Fracture Assessment: Formulation and Validation
Rigid particle models (PMs) that explicitly consider the influence of the aggregate structure and its physical interaction mechanisms have been used to predict cracking phenomena in concrete. PMs have also been applied to reinforced concrete fracture, but the known studies have adopted simplified reinforcement and reinforcement/particle interaction models. In this work, a novel 3D explicit discrete element formulation of reinforcement bars discretized through several rigid cylindrical segments is proposed, allowing the 3D reinforced particle model (3D-RPM) to be applied to reinforced concrete fracture studies, namely for shear failure. The 3D-RPM is evaluated using known three-point and four-point bending tests on reinforced concrete beams without stirrups and on known shear transfer tests due to dowel action. The 3D-RPM model is shown to reproduce the crack propagation, and the load displacement response observed experimentally for different steel contents under three-point bending, for different beam sizes, under four-point bending, and for different bar diameters, under shear. The validation examples highlight the importance of including a nonlinear reinforcement/particle interaction model. As shown, an elastic model contact leads to higher vertical loads in three-point and four-point bending tests for the same set of contact properties and, in the shear tests, leads to an overestimation of the maximum shear strength and to an increase in the model initial stiffness.
- 5 January 2025
- Published by MDPI AG in Applied Mechanics
- Vol. 6 (1) , 2
Open AccessA Novel 3D Reinforced Particle Model for Reinforced Concrete Fracture Assessment: Formulation and Validation
Rigid particle models (PMs) that explicitly consider the influence of the aggregate structure and its physical interaction mechanisms have been used to predict cracking phenomena in concrete. PMs have also been applied to reinforced concrete fracture, but the known studies have adopted simplified reinforcement and reinforcement/particle interaction models. In this work, a novel 3D explicit discrete element formulation of reinforcement bars discretized through several rigid cylindrical segments is proposed, allowing the 3D reinforced particle model (3D-RPM) to be applied to reinforced concrete fracture studies, namely for shear failure. The 3D-RPM is evaluated using known three-point and four-point bending tests on reinforced concrete beams without stirrups and on known shear transfer tests due to dowel action. The 3D-RPM model is shown to reproduce the crack propagation, and the load displacement response observed experimentally for different steel contents under three-point bending, for different beam sizes, under four-point bending, and for different bar diameters, under shear. The validation examples highlight the importance of including a nonlinear reinforcement/particle interaction model. As shown, an elastic model contact leads to higher vertical loads in three-point and four-point bending tests for the same set of contact properties and, in the shear tests, leads to an overestimation of the maximum shear strength and to an increase in the model initial stiffness.
- Open Access
- 22 July 2024
- Published by MDPI AG in Infrastructures
- Vol. 9 (7) , 118
Incremental Viscoelastic Damage Contact Models for Asphalt Mixture Fracture Assessment
Asphalt mixtures are widely used as a surfacing material for pavements due to their several advantages. For this reason, robust numerical models still need to be developed to improve the understanding of their fracture behaviour. Recently, an incremental generalised Kelvin (GK) contact model that relates increments in contact displacements with increments in contact forces was proposed to assess the viscoelastic behaviour of asphalt mixtures within a discrete element method (DEM) framework. In this work, the contact model is extended to allow its application to asphalt mixture fracture studies. Two damage models—a brittle and a bilinear softening—coupled with the GK contact model are proposed to consider damage initiation and propagation. A parametric study is presented that assesses the impact of the GK-Damage parameters, showing a sensitivity to the loading velocity and the Maxwell elements, particularly its viscosity element, on the stress–strain response of a single contact. A reduced-size numerical mastic is initially used to speed up the calibration process of the GK-Damage contact parameters, with subsequent validation on a specimen with real experimental dimensions. It is shown that the proposed calibrated damage models can successfully reproduce the time-dependent behaviour, peak stress, and crack path observed in experimental results, highlighting the benefits of the adopted methodology. For the GK-Bilinear model, the fracture energy and maximum contact tensile stress are shown to adjust both the peak stress and softening response. Uniaxial tensile tests on asphalt mixtures indicate that the GK-Bilinear model provides a more realistic characterisation of fracture development. A higher susceptibility to damage at aggregate-to-mastic contacts compared to contacts within the mastic phase is identified.
- 22 July 2024
- Published by MDPI AG in Infrastructures
- Vol. 9 (7) , 118
Open AccessIncremental Viscoelastic Damage Contact Models for Asphalt Mixture Fracture Assessment
Asphalt mixtures are widely used as a surfacing material for pavements due to their several advantages. For this reason, robust numerical models still need to be developed to improve the understanding of their fracture behaviour. Recently, an incremental generalised Kelvin (GK) contact model that relates increments in contact displacements with increments in contact forces was proposed to assess the viscoelastic behaviour of asphalt mixtures within a discrete element method (DEM) framework. In this work, the contact model is extended to allow its application to asphalt mixture fracture studies. Two damage models—a brittle and a bilinear softening—coupled with the GK contact model are proposed to consider damage initiation and propagation. A parametric study is presented that assesses the impact of the GK-Damage parameters, showing a sensitivity to the loading velocity and the Maxwell elements, particularly its viscosity element, on the stress–strain response of a single contact. A reduced-size numerical mastic is initially used to speed up the calibration process of the GK-Damage contact parameters, with subsequent validation on a specimen with real experimental dimensions. It is shown that the proposed calibrated damage models can successfully reproduce the time-dependent behaviour, peak stress, and crack path observed in experimental results, highlighting the benefits of the adopted methodology. For the GK-Bilinear model, the fracture energy and maximum contact tensile stress are shown to adjust both the peak stress and softening response. Uniaxial tensile tests on asphalt mixtures indicate that the GK-Bilinear model provides a more realistic characterisation of fracture development. A higher susceptibility to damage at aggregate-to-mastic contacts compared to contacts within the mastic phase is identified.
- Open Access
Assessment of Contact Laws Accounting for Softening in 3D Rigid Concrete Particle Models
To obtain predictions closer to concrete behaviour, it is necessary to employ a particle model (PM) that considers contact softening. A bilinear softening contact model (BL) has been adopted in PM studies. Several limitations in PM predictions have been identified that may be due to BL assumptions. For this reason, this paper compares BL predictions with those obtained with more complex models to assess if PM predictions can be improved. As shown, it is possible to calibrate each contact model to reproduce the complex behaviour observed in concrete in uniaxial and biaxial loading. The predicted responses are similar, and the known PM limitations still occur independently of the adopted model. Under biaxial loading, it is shown that a response closer to that observed in concrete can be obtained (higher normal-to-stiffness ratio of ≈0.50, maximum contact compressive strength of ≈60 MPa, and 30% reduction in the number of working contacts). The BL contact model for PM concrete DEM-based simulations is shown to have (i) lower associated computational costs (15% to 50% lower); (ii) a reduced number of contact strength parameters; and (iii) similar responses to those predicted with more complex models. This paper highlights that the BL contact model can be used with confidence in PM fracture studies.
Open AccessAssessment of Contact Laws Accounting for Softening in 3D Rigid Concrete Particle Models
To obtain predictions closer to concrete behaviour, it is necessary to employ a particle model (PM) that considers contact softening. A bilinear softening contact model (BL) has been adopted in PM studies. Several limitations in PM predictions have been identified that may be due to BL assumptions. For this reason, this paper compares BL predictions with those obtained with more complex models to assess if PM predictions can be improved. As shown, it is possible to calibrate each contact model to reproduce the complex behaviour observed in concrete in uniaxial and biaxial loading. The predicted responses are similar, and the known PM limitations still occur independently of the adopted model. Under biaxial loading, it is shown that a response closer to that observed in concrete can be obtained (higher normal-to-stiffness ratio of ≈0.50, maximum contact compressive strength of ≈60 MPa, and 30% reduction in the number of working contacts). The BL contact model for PM concrete DEM-based simulations is shown to have (i) lower associated computational costs (15% to 50% lower); (ii) a reduced number of contact strength parameters; and (iii) similar responses to those predicted with more complex models. This paper highlights that the BL contact model can be used with confidence in PM fracture studies.
- Open Access
Impact of Rejuvenator-Modified Mastic on Asphalt Mixture Stiffness: Meso-Scale Discrete Element Method Approach
Encapsulated rejuvenators embedded in asphalt mixtures are a promising technology to extend the service life of asphalt pavements. However, their effects on the asphalt mixture’s performance still need to be properly understood. A recently developed three-dimensional discrete element method framework enables the evaluation of non-homogeneous distributions of the rejuvenator, closely resembling real conditions. This includes different scenarios involving capsule content and release efficiency. The presented numerical results show that the rejuvenator-to-mastic ratio and the number of rejuvenator-modified contacts influence the stiffness properties of asphalt mixtures. In cases where a homogeneous rejuvenator distribution is assumed, the three-dimensional DEM model predicts a significant reduction in the asphalt mixture’s stiffness that compromises the pavement’s performance. Simulations show that the diffusion effect needs to be considered for predicting the post-healed behavior of asphalt mixtures. For cases considering more suitable modified mastic amounts (less than 1.20 wt%), the effect on the asphalt mixture’s stiffness modulus is less pronounced, and the phase angle is not significantly affected. Additionally, the presented simulations suggest that the capsule content can be increased up to 0.75 wt%, and capsules with a release rate higher than 48% can be used without compromising the rheological performance of asphalt mixtures, possibly improving their self-healing properties. These numerical insights should be considered in future designs to achieve optimal post-healed behavior.
Open AccessImpact of Rejuvenator-Modified Mastic on Asphalt Mixture Stiffness: Meso-Scale Discrete Element Method Approach
Encapsulated rejuvenators embedded in asphalt mixtures are a promising technology to extend the service life of asphalt pavements. However, their effects on the asphalt mixture’s performance still need to be properly understood. A recently developed three-dimensional discrete element method framework enables the evaluation of non-homogeneous distributions of the rejuvenator, closely resembling real conditions. This includes different scenarios involving capsule content and release efficiency. The presented numerical results show that the rejuvenator-to-mastic ratio and the number of rejuvenator-modified contacts influence the stiffness properties of asphalt mixtures. In cases where a homogeneous rejuvenator distribution is assumed, the three-dimensional DEM model predicts a significant reduction in the asphalt mixture’s stiffness that compromises the pavement’s performance. Simulations show that the diffusion effect needs to be considered for predicting the post-healed behavior of asphalt mixtures. For cases considering more suitable modified mastic amounts (less than 1.20 wt%), the effect on the asphalt mixture’s stiffness modulus is less pronounced, and the phase angle is not significantly affected. Additionally, the presented simulations suggest that the capsule content can be increased up to 0.75 wt%, and capsules with a release rate higher than 48% can be used without compromising the rheological performance of asphalt mixtures, possibly improving their self-healing properties. These numerical insights should be considered in future designs to achieve optimal post-healed behavior.