Matthew J. Kramer

While the Josephson junction is central to qubit operation, overall quantum coherence requires thorough understanding of the entire metallic environment---leads, capacitive pads, and readout resonators. The established contributors to decoherence are surface oxides and hydroxides, as well as absorbed species, such as hydrogen and oxygen. Metal encapsulation of freshly grown surfaces with nonoxidizing metals is a successful strategy to mitigate these issues. To achieve guided optimization, it is significant to understand the microscopic behavior of capped films. Although most attention was paid to the surface and interfaces, bulk properties were not systematically studied. We present a comprehensive study of the bulk superconducting properties of Nb thin films encapsulated with gold and palladium gold and compare them to bare Nb films. Magneto-optical imaging, magnetization, resistivity, and London and Campbell penetration depth measurements reveal significant differences in encapsulated samples. Both sputtered and epitaxial Au-capped films exhibit the highest residual resistivity ratio and superconducting transition temperature and the lowest upper critical field, London penetration depth, and critical current. These observations agree well with the microscopic theory of anisotropic normal and superconducting states of niobium with varying amounts of scattering. We conclude that surface encapsulation significantly affects bulk properties, and gold-coated films are the cleanest. Since these changes reside in the bulk of the niobium rather than in the overlayer, they may in turn influence the processes that limit quantum coherence. Considering such a strong variation of properties, we believe that the question of whether the surface or bulk is the dominant contributor to quantum decoherence is wide open. However, they likely both contribute via different mechanisms, which makes it very hard to pinpoint where the bottleneck is.

The Superconducting Quantum Materials and Systems Center, a U. S. Department of Energy National Quantum Information Science Research Center, has conducted a comprehensive and coordinated study using superconducting transmon qubit chips with known performance metrics to identify the underlying materials-level sources of device-to-device performance variation. Following qubit coherence measurements, these qubits of varying base superconducting metals and substrates have been examined with various non-destructive and invasive material characterization techniques at Northwestern University, Ames National Laboratory, and Fermilab as part of a blind study. We find trends in variations of the depth of the etched substrate trench, the thickness of the surface oxide, and the geometry of the sidewall, which when combined, lead to correlations with the T1 lifetime across different qubits on the same chip. In addition, we provide a list of features that varied from device to device, for which the impact on performance requires further studies. Finally, we identify two low-temperature characterization techniques that may potentially serve as proxy tools for qubit measurements. These insights provide materials-oriented solutions to not only reduce performance variations across neighboring devices but also to engineer and fabricate devices with optimal geometries to achieve performance metrics beyond the state-of-the-art values.

Hydrogenation-Disproportionation-Desorption-Recombination (HDDR) is an effective method for producing high coercivity, anisotropic powder from either fresh Nd-Fe-B alloy or recycled Nd-Fe-B magnets for use in bonded magnets. We investigated the impact of surface defects on the coercivity of HDDR-processed Nd-Fe-B using scanning electron microscopy (SEM), magnetic measurements, and micromagnetic simulations. We observed that coercivity decreases as particle size reduces, with SEM revealing surface defects and the detachment of Nd2Fe14B grains and Nd-rich phases from the particle surface. Micromagnetic simulations indicate that demagnetization initiates at the particle surface, where these defects are most concentrated, leading to reduced coercivity. The reduction in squareness of demagnetization curve, knee point field and coercivity for smaller HDDR particles is attributed to an increased specific surface area, which exhibits reduced nucleation field and weak domain wall pinning field during magnetization reversal. By addressing the role of surface defects in coercivity degradation, this study provides insights for improving both new powder production and recycling strategies, ultimately leading to enhanced performance of bonded magnets and contributing to more sustainable practices in the rare earth supply chain. One potential strategy to enhance the performance of HDDR Nd-Fe-B materials involves reducing the fraction of fine particles (<35 µm) and promoting the formation of grain boundary phases on particle surfaces.

Correlating superconducting qubit performance with advanced materials analysis is a key strategy for improving coherence. Existing diagnostics for key properties, such as dielectric loss, structural discontinuity, and interface heterogeneity, often rely on destructive electron microscopy or low-throughput millikelvin measurements. Here, we demonstrate noninvasive terahertz (THz) nano-imaging/spectroscopy of encapsulated niobium transmon qubits as a high-throughput proxy for performance evaluation. We identify large variations in sidewall near-field signals, implicating sidewall loss and discontinuity as major coherence limiters, and also use THz hyperspectral line scans to probe dielectric responses and field participation at Al junction interfaces.

The London penetration depth, λ ( T ) , was measured in various forms of niobium, including foils, thin films, single crystals, and samples from superconducting radio-frequency (SRF) cavities. We observed a significant difference in λ ( T ) at low temperatures, T < T c / 3 , due to low-energy quasiparticles. In particular, an unusual downturn of λ ( T ) on cooling in the SRF cavity samples required to take into account deep in-gap bound states. Theoretical modeling using the generalized Dynes density of states shows that such in-gap states lead to a downturn or a peak in λ ( T ) upon cooling. Combined, experimental and theoretical findings provide a method for detecting two-level systems or states related to magnetic impurities in the bulk of niobium. This result is particularly relevant for the quantum informatics sciences technologies used in qubits and circuit quantum electrodynamics architecture based on SRF cavities.

The performance of superconducting qubits is often limited by dissipation and two-level systems (TLS) losses. The dominant sources of these losses are believed to originate from amorphous materials and defects at interfaces and surfaces, likely as a result of fabrication processes or ambient exposure. Here, we explore a novel wet chemical surface treatment at the Josephson junction-substrate and the substrate-air interfaces by replacing a buffered oxide etch (BOE) cleaning process with one that uses hydrofluoric acid followed by aqueous ammonium fluoride. We show that the ammonium fluoride etch process results in a statistically significant improvement in median T 1 by ∼ 22 % (p = 0.002), and a reduction in the number of strongly-coupled TLS in the tunable frequency range. Microwave resonator measurements on samples treated with the ammonium fluoride etch after niobium deposition and etching also show ∼ 33 % lower TLS-induced loss tangent compared to the BOE treated samples. As the chemical treatment primarily modifies the Josephson junction-substrate interface and substrate-air interface, we perform targeted chemical and structural characterizations to examine materials differences at these interfaces and identify multiple microscopic changes that could contribute to decreased TLS losses.