RKRyuunosuke Kuroda

Ryuunosuke Kuroda

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Ryuunosuke Kuroda has a total of 385 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Nondestructive quantitative imaging for spatially nonuniform degradation in a commercial lithium-ion battery using a pulsed neutron beam

    by Koichi Kino, Takanori Itoh, Takeshi Fujiwara, Ryunosuke Kuroda, Nagayasu Oshima, Masahito Tanaka, Akira Watazu, Takashi Kamiyama, Masao Yonemura, Yoshihisa Ishikawa

    A quantitative nondestructive Bragg-edge imaging technique for power-storage degradation was developed using commercial prismatic-shaped lithium-ion battery cells. The C or Li atoms/ions column density [cm−2] images for five phases of the negative electrode material (graphite, Li0.04C6, Li0.2C6, Li0.5C6, and Li1.0C6) with a 1 mm spatial resolution were obtained by considering the crystalline orientation for both fresh and fatigue cells. In the fresh cell, most of the graphite was uniformly converted to Li1.0C6 by charging, and in the fatigue cell, the graphite changed to various phases (especially, Li1.0C6 and Li0.5C6) by charging, and their spatial distributions were nonuniform.


  • Open Access

    Time-domain measurement of coherent transition radiation using a photoconductive antenna with micro-structured electrodes

    by K. Kan, M. Gohdo, J. Yang, I. Nozawa, Y. Yoshida, H. Kitahara, K. Takano, R. Kuroda, H. Toyokawa

    The longitudinal electric field profile of coherent transition radiation (CTR), which is a radially polarized terahertz (THz) pulse from an electron bunch, was measured using a large-aperture photoconductive antenna (PCA) with a diameter of 8.8 mm and micro-structured concentric electrodes to detect THz light pulses. Photo-induced charge carriers were generated on the PCA by the irradiation of femtosecond laser pulses on the electrode plane. Pulsed light irradiation enabled time-resolved measurement of the THz light pulses, and time-domain measurement of CTR was conducted by measuring the electric-field-induced current output from the PCA by sweeping the timing of the laser irradiation. The frequency spectra obtained from the detected longitudinal electric field profiles of the CTR showed a reasonable response signal from the low-frequency region as low as 0.1 THz. In the present demonstration, the large-aperture PCA-detected THz wave from the CTR was from 0.1 to at least 1 THz. THz generation using the PCA was also performed and measured using a Michelson interferometer with a helium-cooled bolometer. Comparison of the THz pulse of the CTR detected using the PCA and that generated using the PCA revealed that time-domain measurement of the THz pulse using the PCA was limited by the response time of the charge carriers in the semiconductor. Enlargement of the aperture of the PCA enhanced the detectable frequency region toward a lower frequency.


  • Direct generation of sub-picosecond pulse via multi-section gain switching

    by Takahiro Nakamura, Takashi Ito, Hidekazu Nakamae, Changsu Kim, Yuji Hazama, Yohei Kobayashi, Ryunosuke Kuroda, Hidefumi Akiyama

    We have directly generated optical pulses having a duration of 0.56 ps with a peak power of 25 W by gain switching of multi-section semiconductor lasers in which the optimized lengths of the absorption and gain regions were 50 and 200 µm, respectively. Even though the experiment was conducted via impulsive optical pumping at a low temperature, we observed that the multi-section gain switching suppresses the low-energy tail and chirping inherent to conventional gain switching in single-section lasers and is useful in direct short-pulse generation.


  • Ablation threshold and crater morphology of amorphous and crystalline SiO 2 glass for extreme ultraviolet femtosecond pulses

    by Tatsunori Shibuya, Kazuyuki Sakaue, Hiroshi Ogawa, T.-H. Dinh, Daisuke Satoh, Eichi Terasawa, Masakazu Washio, Masahito Tanaka, Takeshi Higashiguchi, Masahiko Ishino, et al.

    The ablation threshold fluence and crater morphology of amorphous and crystalline SiO 2 glass were analyzed in the regime of an extreme ultraviolet femtosecond pulse. Despite the difference between the densities (or optical penetration depths) of amorphous and crystalline SiO 2 glass, the ablation threshold fluences and crater morphologies were found to be comparable. In addition, we compared our experimental results at a 10.3 nm wavelength with those in a previous work at a 13.5 nm wavelength. We conclude that the impact of the difference in density or optical penetration depth of several tens of percent on the ablation process is limited.


  • Ablation thresholds and morphological changes of poly‐ l ‐lactic acid for pulse durations in the femtosecond‐to‐picosecond regime

    by Tatsunori Shibuya, Dai Yoshitomi, Daisuke Satoh, Kazuyuki Sakaue, Masahito Tanaka, Hideyuki Takada, Hiroshi Ogawa, Kenji Torizuka, Yohei Kobayashi, Ryunosuke Kuroda

    Biodegradable polymers such as poly‐ l ‐lactic acid (PLLA) are essential tools for a wide range of medical applications because of their mechanical robustness and bio‐affinity. Laser processing is commonly used to construct various structures from biodegradable polymers. However, in general, polymers deteriorate rapidly owing to laser‐induced heating effects. In this study, we investigate the optimum irradiation conditions for PLLA processing, using an ultrafast laser and finely controlling the pulse duration over the femtosecond‐to‐picosecond range. We report on the morphological characteristics of the craters generated by single‐shot and multiple‐shot laser irradiation under pulse duration control. Our results show that crater morphology and damage threshold in the single‐shot regime depend on pulse duration and that the degree of crater unevenness is insensitive to pulse duration in the multishot regime.


  • Effect of aggregation on hydration of HSA protein: Steady-state Terahertz absorption spectroscopic study

    by Biswajit Manna, Amitabha Nandi, Masahito Tanaka, Hiroyuki Toyokawa, Ryunosuke Kuroda, Dipak K Palit


  • Characterization of binary Ce–Ir alloy photocathodes

    by Daisuke Satoh, Tatsunori Shibuya, Hiroshi Ogawa, Masahito Tanaka, Hiromi Ikeura-Sekiguchi, Ryunosuke Kuroda, Mitsuhiro Yoshida, Hitoshi Sugawara, Hiroyuki Toyokawa

    Binary Ce–Ir alloys nominally containing 83, 78, 75, and 67 at% Ir were grown via arc melting in order to clarify the optimum composition for a Ce–Ir system to be used as photocathode material. Scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), and X-ray diffraction (XRD) analysis were employed to characterize the microstructure and phase composition of these alloys. The results of the XRD analyses and SEM/EDX measurements indicated that single-phase homogeneous crystals composed of CeIr 2 grains were successfully grown in the sample with an iridium content amounting to 67 at%. Through quantum efficiency (QE) measurements, it was revealed that the QE of the Ce-67 at% Ir alloy (CeIr 2 phase) is a few times higher than that of the other Ce–Ir alloys.


  • Femto- and nanosecond pulse duration dependence of the single-shot ablation threshold and multiple-shot morphology change of poly L-lactic acid in deep ultraviolet regime

    by Tatsunori Shibuya, Daisuke Satoh, Masahito Tanaka, Hiroshi Ogawa, Ryunosuke Kuroda

    Laser processing is a common method used to shape various structures of biodegradable polymers. In this study, we demonstrate PLLA processing with intense deep ultraviolet (DUV) pulses at 266 nm and compare the processing properties using a nanosecond DUV laser. Results allow comparison of the single-shot ablation thresholds and multiple-shot morphology of both the femtosecond and nanosecond DUV laser. For sing-shot experiments, the ablation threshold of femtosecond laser is, at least, one order of magnitude lower than that of nanosecond laser. For multiple-shot experiments, the result provides superior quality of the crater morphology in the DUV femtosecond regime.


  • Deep-hole drilling of amorphous silica glass by extreme ultraviolet femtosecond pulses

    by Tatsunori Shibuya, Takashi Takahashi, Kazuyuki Sakaue, Thanh-Hung Dinh, Hiroyuki Hara, Takeshi Higashiguchi, Masahiko Ishino, Yuya Koshiba, Masaharu Nishikino, Hiroshi Ogawa, et al.

    A free-electron laser (FEL) is a robust tool for studying the interaction of intense X-rays with matter. In this study, we investigate the damage threshold and morphology of fused silica irradiated by extreme ultraviolet femtosecond pulses of a FEL. The experimental results indicate the superiority of the FEL processing. The FEL-damage threshold of fused silica at a wavelength of 13.5 nm is 0.17 J/cm2, which is 20 times lower than that of a near infrared (NIR) femtosecond laser. The relationship between the crater depth and laser fluence reveals that the effective absorption length is αeff−1 = 58 nm. The damage threshold and the absorption length are the key values for smooth crater formation. In addition, the formation of rim structures and microcracks, which are usually the critical issues in NIR laser processing, cannot be found in the interaction region. The hole diameter is maintained below the beam size at the exit.


  • Real-time X-ray visualization of ink penetration into powder bed for binder jetting process

    by Shin Mizutani, Daichi Yamaguchi, Takeshi Fujiwara, Masato Yasumoto, Ryunosuke Kuroda

    We have developed an in-situ X-ray imaging system to visualize penetration dynamics of small ink droplets into powder bed in binder jetting process. The imaging system consists of a micro focus X-ray source, an ink depositing device by remote control and a high resolution flat panel detector. The whole process of the ink penetration, such as ink penetration through the powder bed and powder bed densification, was visualized in sequence applying this system. The results show that the difference of the amount of ink cause the change of the powder bed densification and the penetration distance in depth and plane direction. The real-time visualization of the ink penetration dynamics can be useful to clarify the mechanism of the defects in the fabricated objects, such as internal porosity and weak bonds between the layers.