DLDongchen Lan

Dongchen Lan

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Dongchen Lan has a total of 63 co-authors. Here are the top co-authors by number of shared publications:

  • Martin A. Green

    University of New South Wales School of Photovoltaic and Renewable Energy Engineering Sydney 2052, Australia

    8 shared publications
  • Dawei Di

    State Key Laboratory of Extreme Photonics and Instrumentation, College of Optical Science and Engineering, Zhejiang University, Hangzhou, China

    5 shared publications
  • Chen Zou

    State Key Laboratory of Modern Optical Instrumentation, College of Optical Science and Engineering, International Research Center for Advanced Photonics, Zhejiang University, Hangzhou 310027, China

    3 shared publications
  • Dexin Yang

    College of Materials & Environmental Engineering, Hangzhou Dianzi University, Hangzhou 310018, China

    3 shared publications
  • Ruihao Gong

    College of Electrical Engineering, Zhejiang University, Hangzhou 310027, China

    3 shared publications
  • Yaxiao Lian

    State Key Laboratory of Extreme Photonics and Instrumentation, College of Optical Science and Engineering; International Research Center for Advanced Photonics, Zhejiang University, Hangzhou 310027, China

    3 shared publications

Latest Publications

  • Open Access

    Retarding efficiency loss upon scaling in perovskite photovoltaics as fill factor becomes the bottleneck

    by Buyi Yan, Ruihao Gong, Yanchun Huang, Nannan Gu, Runfeng Li, Dongxue Liu, Kangrong Yan, Xuehui Xu, Yang Michael Yang, Jizhong Yao, et al.

    Perovskite solar cells approach crystalline-silicon efficiencies at small areas, yet substantial performance losses during scale-up hinder their translation into practical modules. Here we quantify the contributions of device-performance parameters to efficiency loss during scale-up across diverse perovskite technologies, identifying fill factor ( $${FF}$$ F F ) as a major contributor and target for mitigating this loss. Further analysis resolves the FF deficit into voltage-, diode-non-ideality- and transport-associated contributions. Cryo-controlled processing provides an experimental route to preserve $${FF}$$ F F by regulating intermediate-phase evolution during crystallization. The resulting $${FF}$$ F F -preservation advantage arises predominantly from reduced diode non-ideality, with the other contributions being smaller. This advantage increases across device scales. A mini-module (19.48 cm 2 aperture) achieves a record certified steady-state efficiency of 23.9% with an $${FF}$$ F F of 83.3%, the highest reported for perovskite modules. The same $${FF}$$ F F limitation governs operational performance decay, linking efficiency retention during scale-up with long-term stability. Together, these results establish $${FF}$$ F F preservation and the factors governing it as central to mitigating performance loss during scale-up and operation.

  • Open Access

    One-shot luminescence diagnostics for field-scale photovoltaics

    by Dingkun Peng, Jing Chai, Dongchen Lan

  • Stabilizing perovskite fabrication in ambient air

    by Ruihao Gong, Buyi Yan, Dongchen Lan

  • Open Access

    Strain analysis of black-to-yellow phase transitions in CsPbI3

    by Dexin Yang, Bangwei Jin, Ruihao Gong, Dongchen Lan, Xuefeng Zhang

    All-inorganic halide perovskite cesium lead iodide (CsPbI3) has emerged as a promising semiconductor and optoelectronic material. However, its optically active black phases easily transform into the non-optically active yellow phase, limiting practical applications. Here, strain variations during phase transitions in CsPbI3 are investigated using a strain/order parameter coupling model, based on lattice parameters measured over the temperature range of 100–650 K. Structural and thermal analyses suggest that the large positive (e₁-e₂) strain is the primary driver responsible for the transformation of black CsPbI₃ into the yellow phase. The impact of this strain on the phase stability of CsPbI₃-based films is further validated by comparing films on different substrates and with varying compositions. Our findings uncover the key metric that determines the phase stability of CsPbI3, providing insights for the design of stable, optically active all-inorganic halide perovskite.

  • Open Access

    Reverse-bias challenges facing perovskite-silicon tandem solar cells under field conditions

    by Runfeng Li, Ruihao Gong, Heming Lin, Martin A. Green, Dongchen Lan


  • Reduced-Toxicity and Highly Luminescent Germanium–Lead Perovskites Enabled by Strain Reduction for Light-Emitting Diodes

    by Yanjun Zhou, Chen Zou, Dingkun Peng, Bangwei Jin, Min Rao, Dongchen Lan, Dexin Yang, Dawei Di, Xuefeng Zhang

    Germanium-lead (Ge-Pb) perovskites provide a promising solution for perovskite optoelectronic devices with reduced toxicity. However, Ge-Pb perovskite light-emitting diodes (PeLEDs) with >30 mol % Ge showed low emission efficiencies [Yang, D.; Zhang, G.; Lai, R.; Cheng, Y.; Lian, Y.; Rao, M.; Huo, D.; Lan, D.; Zhao, B.; Di, D. Germanium-Lead Perovskite Light-Emitting Diodes. Nat. Commun. 2021, 12 (1), 4295]. Here, we apply strain engineering to effectively improve the light emission efficiency and stability of Ge-Pb perovskite films and PeLEDs with 30 and 60 mol % Ge, through A-site modulation. The maximum external quantum efficiencies of the Ge-Pb PeLEDs with 30 and 60 mol % Ge are 8.5% and 3.0% at 3.32 mA cm-2 (∼922 cd m-2) and 0.53 mA cm-2 (∼60 cd m-2), respectively. Time-resolved transient absorption spectroscopy analysis of Ge-Pb perovskite films on different hole-transport layers shows that incorporating 30 mol % Ge into the perovskite with mixed A-site cations can effectively suppress trap-assisted recombination. Further analysis of their current density-voltage (J-V) curves reveals the efficiency loss mechanisms of Ge-Pb PeLEDs with high Ge fractions, indicating the possibility of further improvements.


  • Bright and Stable Red Perovskite LEDs under High Current Densities

    by Zhixiang Ren, Bingbing Guo, Shengnan Liu, Yaxiao Lian, Yaxin Wang, Shiyu Xing, Yichen Yang, Gan Zhang, Weidong Tang, Yuxiang Gao, et al.

    Perovskite LEDs (PeLEDs) have emerged as a next-generation light-emitting technology. Recent breakthroughs were made in achieving highly stable near-infrared and green PeLEDs. However, the operational lifetimes (T50) of visible PeLEDs under high current densities (>10 mA cm-2) remain unsatisfactory (normally T50 lifetimes of up to ∼357 h at currents of ≥25 mA cm-2, a record for the operational stability of visible PeLEDs under high current densities. The devices produce intense and stable emission with a maximum luminance of 28,870 cd m-2 (radiance: 1584 W sr-1 m-2), which is record-high for red PeLEDs. Key to this demonstration is the introduction of sulfonamide, a dipolar molecular stabilizer that effectively interacts with the ionic species in the perovskite emitters. It suppresses halide segregation and migration into the charge-transport layers, resulting in enhanced stability and brightness of the mixed-halide PeLEDs. These results represent a substantial step toward bright and stable PeLEDs for emerging applications.


  • Open Access

    Ultralow-voltage operation of light-emitting diodes

    by Yaxiao Lian, Dongchen Lan, Shiyu Xing, Bingbing Guo, Zhixiang Ren, Runchen Lai, Chen Zou, Baodan Zhao, Richard H. Friend, Dawei Di

    For a light-emitting diode (LED) to generate light, the minimum voltage required is widely considered to be the emitter’s bandgap divided by the elementary charge. Here we show for many classes of LEDs, including those based on perovskite, organic, quantum-dot and III–V semiconductors, light emission can be observed at record-low voltages of 36–60% of their bandgaps, exhibiting a large apparent energy gain of 0.6–1.4 eV per photon. For 17 types of LEDs with different modes of charge injection and recombination (dark saturation currents of ~10−39–10−15 mA cm−2), their emission intensity-voltage curves under low voltages show similar behaviours. These observations and their consistency with the diode simulations suggest the ultralow-voltage electroluminescence arises from a universal origin—the radiative recombination of non-thermal-equilibrium band-edge carriers whose populations are determined by the Fermi-Dirac function perturbed by a small external bias. These results indicate the potential of low-voltage LEDs for communications, computational and energy applications.


  • Open Access

    Germanium-lead perovskite light-emitting diodes

    by Dexin Yang, Guoling Zhang, Runchen Lai, Yao Cheng, Yaxiao Lian, Min Rao, Dexuan Huo, Dongchen Lan, Baodan Zhao, Dawei Di

    Reducing environmental impact is a key challenge for perovskite optoelectronics, as most high-performance devices are based on potentially toxic lead-halide perovskites. For photovoltaic solar cells, tin-lead (Sn–Pb) perovskite materials provide a promising solution for reducing toxicity. However, Sn–Pb perovskites typically exhibit low luminescence efficiencies, and are not ideal for light-emitting applications. Here we demonstrate highly luminescent germanium-lead (Ge–Pb) perovskite films with photoluminescence quantum efficiencies (PLQEs) of up to ~71%, showing a considerable relative improvement of ~34% over similarly prepared Ge-free, Pb-based perovskite films. In our initial demonstration of Ge–Pb perovskite LEDs, we achieve external quantum efficiencies (EQEs) of up to ~13.1% at high brightness (~1900 cd m−2), a step forward for reduced-toxicity perovskite LEDs. Our findings offer a new solution for developing eco-friendly light-emitting technologies based on perovskite semiconductors.


  • The physics of ion migration in perovskite solar cells: Insights into hysteresis, device performance, and characterization

    by Dongchen Lan

    Perovskite solar cells promise to reach the highest efficiencies at the lowest costs, but the mobile ions create challenges in both cell measurements and performance improvement. Being able to understand the ion migration mechanism and its impacts would help to solve relevant issues and may open up opportunities for further development. Although some efforts have been made here, explanations are often too exotic resulting in not only some controversies but the neglect of some important aspects addressable by familiar concepts. This paper uses familiar knowledge in solar cell device physics to explain the ion migration mechanism and its impacts under conditions of interests. It is shown that, when depletion layers contract such as in a forward current‐voltage scan, tardy ionic charges can distort the perovskite bands hence reduce the net currents before they move to new equilibriums, causing the hysteresis effect. As ion migration impacts the electron and hole distributions, it can affect the Shockley‐Read‐Hall and Auger processes differently, hence may either reduce or increase the ratio of radiative to nonradiative recombination. This previously unaddressed mechanism for variation in the electron‐hole recombination can explain photoluminescence quenching and enhancement as well as performance degradation and improvement during ion migration.