Rafael Schouwenaars
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Rafael Schouwenaars has a total of 75 co-authors. Here are the top co-authors by number of shared publications:
- Carlos Gabriel Figueroa
Universidad Nacional Autónoma de México
8 shared publications A. Ortiz
5 shared publications- Víctor Hugo Jacobo
Universidad Nacional Autónoma de México
5 shared publications Armando Ortiz
3 shared publications- Armando Ortiz
Departamento de Materiales y Manufactura, Facultad de Ingeniería, Edificio O, Universidad Nacional Autónoma de México (UNAM), Ciudad Universitaria, Coyoacán, Mexico City 04510, Mexico
3 shared publications - Myriam Solís-López
Universidad Nacional Autónoma de México
3 shared publications
Latest Publications
- Open Access
Modelling the Mechanical Properties of Architected Cellular Solids for Structural Applications: A Review
Among a broad range of promising applications, the use of cellular solids as lightweight structural components is an important field of research that requires reliable predictions of their stiffness and strength. Predictive and general models should not depend on extensive parameter-fitting experiments and should not rely on computationally intensive numerical calculations for each new set of geometric parameters and loading conditions. An overview of models for 2D, 2.5D, and three-dimensional structures will be presented. Most 2D and 2.5D models neglect out-of-plane behaviour and the face sheets used in sandwich panels. 3D studies, mainly by finite element models (FEMs), are often limited to a narrow set of geometries and simple loading conditions. Elastic anisotropy is well covered, but calculating yield surfaces remains a challenge. Simplified models based on structural mechanics are rare and often limited in scope. They offer a flexible, computationally efficient approach for simulating truss-based materials. For more advanced designs, parameter-based FEMs must be developed for any loading condition to facilitate the generalised incorporation of 3D cellular solids in mechanical design. Artificial intelligence and machine learning are promising approaches for making optimal use of experimental and FEM results across multidimensional parameter spaces.
Open AccessModelling the Mechanical Properties of Architected Cellular Solids for Structural Applications: A Review
Among a broad range of promising applications, the use of cellular solids as lightweight structural components is an important field of research that requires reliable predictions of their stiffness and strength. Predictive and general models should not depend on extensive parameter-fitting experiments and should not rely on computationally intensive numerical calculations for each new set of geometric parameters and loading conditions. An overview of models for 2D, 2.5D, and three-dimensional structures will be presented. Most 2D and 2.5D models neglect out-of-plane behaviour and the face sheets used in sandwich panels. 3D studies, mainly by finite element models (FEMs), are often limited to a narrow set of geometries and simple loading conditions. Elastic anisotropy is well covered, but calculating yield surfaces remains a challenge. Simplified models based on structural mechanics are rare and often limited in scope. They offer a flexible, computationally efficient approach for simulating truss-based materials. For more advanced designs, parameter-based FEMs must be developed for any loading condition to facilitate the generalised incorporation of 3D cellular solids in mechanical design. Artificial intelligence and machine learning are promising approaches for making optimal use of experimental and FEM results across multidimensional parameter spaces.
- Open Access
- 10 February 2026
- Published by Springer Nature in Shape Memory and Superelasticity
- Vol. 12 (1) , 205-222
Strain Incompatibility as the Cause for Non-Schmid Variant Selection in an Oligocrystalline Cu-Al-Be Shape Memory Alloy
- 10 February 2026
- Published by Springer Nature in Shape Memory and Superelasticity
- Vol. 12 (1) , 205-222
Open AccessStrain Incompatibility as the Cause for Non-Schmid Variant Selection in an Oligocrystalline Cu-Al-Be Shape Memory Alloy
- Open Access
- 13 January 2026
- Published by Trans Tech Publications, Ltd. in Defect and Diffusion Forum
- Vol. 446, 13-19
Modelling Combined Hardening Mechanisms in Alloys through the Analysis of Dislocation Percolation
The critical resolved shear strength of pure metals is given by the Peierls-Nabarro equation; impurities or alloying elements will significantly increase . Additional strength is introduced by strain hardening (SH), the grain size effect (GSE), precipitates and particle dispersion. The combination of these mechanisms is generally described in an additive manner, which can be justified by the Taylor expansion of a multivariate function. This approach is highly empirical and involves extensive parameter fitting. The Kocks-Mecking model (KM) and discrete dislocation dynamics show that SH is mainly due to forest effects (latent hardening). Consequently, the main explanation for alloy strength must be sought in the resistance against dislocation percolation through a field of obstacles with different strengths, with the slip length limited by the grain diameter. This hypothesis is explored by reviving early graphical simulations to the percolation problem by introducing a grain boundary and variable obstacle strength in an efficient computer program. Such simulations and theoretical considerations demonstrate the limitations of the additive description of combined hardening. An alternative approximation is proposed, based on the statistical analysis of dislocation percolation, dislocation junctions and dislocation-grain boundary interaction.
- 13 January 2026
- Published by Trans Tech Publications, Ltd. in Defect and Diffusion Forum
- Vol. 446, 13-19
Open AccessModelling Combined Hardening Mechanisms in Alloys through the Analysis of Dislocation Percolation
The critical resolved shear strength of pure metals is given by the Peierls-Nabarro equation; impurities or alloying elements will significantly increase . Additional strength is introduced by strain hardening (SH), the grain size effect (GSE), precipitates and particle dispersion. The combination of these mechanisms is generally described in an additive manner, which can be justified by the Taylor expansion of a multivariate function. This approach is highly empirical and involves extensive parameter fitting. The Kocks-Mecking model (KM) and discrete dislocation dynamics show that SH is mainly due to forest effects (latent hardening). Consequently, the main explanation for alloy strength must be sought in the resistance against dislocation percolation through a field of obstacles with different strengths, with the slip length limited by the grain diameter. This hypothesis is explored by reviving early graphical simulations to the percolation problem by introducing a grain boundary and variable obstacle strength in an efficient computer program. Such simulations and theoretical considerations demonstrate the limitations of the additive description of combined hardening. An alternative approximation is proposed, based on the statistical analysis of dislocation percolation, dislocation junctions and dislocation-grain boundary interaction.
- Open Access
Influence of heat treatment on the wear behavior of an Al-Cu-Mg-Sn MMC reinforced with TiB2
- Open Access
- 16 February 2025
- Published by Elsevier in Engineering Failure Analysis
- Vol. 172
Connecting macroscopic mechanical models to micromechanical phenomena in the failure analysis of a large-diameter prestressed concrete cylinder pipeline
- 16 February 2025
- Published by Elsevier in Engineering Failure Analysis
- Vol. 172
Open AccessConnecting macroscopic mechanical models to micromechanical phenomena in the failure analysis of a large-diameter prestressed concrete cylinder pipeline
- Open Access
- 6 August 2024
- Published by Springer Nature
- p. 337-346
Comparison of Laser Coordinate Measurements and Hierarchical Multiscale Finite Element Models for the Cup Drawing of Three Commercial Aluminum Alloys
Cup drawing is a benchmark experiment frequently used to validate anisotropic constitutive models and multiscale crystal plasticity codes for yield locus prediction. Earing of the cup rim and thickness variation along the cup wall are sensitive to plastic anisotropy. This test was implemented on an industrial forming press and applied to 85 mm diameter disks of commercial AA1100, AA3103, and AA5005 alloy sheet. Cup geometry was determined using a laser probe coordinate measurement machine (CMM). Finite element models (FEM) were developed with ABAQUS Explicit software and a user-defined subroutine for the anisotropic yield locus based on the hierarchical multiscale model (HMS). As the coordinate cloud produced by the CMM is unrelated to the nodes of the deformed FEM-mesh, both were fitted to a polynomial-Fourier series expansion. After cleaning and correction of the CMM data, point-by-point comparison can be performed between model and experiment. For AA1100, the position of the ears was correctly identified but their magnitude was underestimated. Excellent coincidence was found for AA5005, with strong ears at 0 and 90°. The small ears at -30° and 30° and secondary ears at 90° were correctly predicted for AA3013.
- 6 August 2024
- Published by Springer Nature
- p. 337-346
Open AccessComparison of Laser Coordinate Measurements and Hierarchical Multiscale Finite Element Models for the Cup Drawing of Three Commercial Aluminum Alloys
Cup drawing is a benchmark experiment frequently used to validate anisotropic constitutive models and multiscale crystal plasticity codes for yield locus prediction. Earing of the cup rim and thickness variation along the cup wall are sensitive to plastic anisotropy. This test was implemented on an industrial forming press and applied to 85 mm diameter disks of commercial AA1100, AA3103, and AA5005 alloy sheet. Cup geometry was determined using a laser probe coordinate measurement machine (CMM). Finite element models (FEM) were developed with ABAQUS Explicit software and a user-defined subroutine for the anisotropic yield locus based on the hierarchical multiscale model (HMS). As the coordinate cloud produced by the CMM is unrelated to the nodes of the deformed FEM-mesh, both were fitted to a polynomial-Fourier series expansion. After cleaning and correction of the CMM data, point-by-point comparison can be performed between model and experiment. For AA1100, the position of the ears was correctly identified but their magnitude was underestimated. Excellent coincidence was found for AA5005, with strong ears at 0 and 90°. The small ears at -30° and 30° and secondary ears at 90° were correctly predicted for AA3013.
- Open Access
- 7 March 2024
- Published by MDPI AG in Fractal and Fractional
- Vol. 8 (3) , 152
Statistical Study of the Bias and Precision for Six Estimation Methods for the Fractal Dimension of Randomly Rough Surfaces
The simulation and characterisation of randomly rough surfaces is an important topic in surface science, tribology, geo- and planetary sciences, image analysis and optics. Extensions to general random processes with two continuous variables are straightforward. Several surface generation algorithms are available, and preference for one or another method often depends on the specific scientific field. The same holds for the methods to estimate the fractal dimension D. This work analyses six algorithms for the determination of D as a function of the size of the domain, variance, and the input value for D, using surfaces generated by Fourier filtering techniques and the random midpoint displacement algorithm. Several of the methods to determine fractal dimension are needlessly complex and severely biased, whereas simple and computationally efficient methods produce better results. A fine-tuned analysis of the power spectral density is very precise and shows how the different surface generation algorithms deviate from ideal fractal behaviour. For large datasets defined on equidistant two-dimensional grids, it is clearly the most sensitive and precise method to determine fractal dimension.
- 7 March 2024
- Published by MDPI AG in Fractal and Fractional
- Vol. 8 (3) , 152
Open AccessStatistical Study of the Bias and Precision for Six Estimation Methods for the Fractal Dimension of Randomly Rough Surfaces
The simulation and characterisation of randomly rough surfaces is an important topic in surface science, tribology, geo- and planetary sciences, image analysis and optics. Extensions to general random processes with two continuous variables are straightforward. Several surface generation algorithms are available, and preference for one or another method often depends on the specific scientific field. The same holds for the methods to estimate the fractal dimension D. This work analyses six algorithms for the determination of D as a function of the size of the domain, variance, and the input value for D, using surfaces generated by Fourier filtering techniques and the random midpoint displacement algorithm. Several of the methods to determine fractal dimension are needlessly complex and severely biased, whereas simple and computationally efficient methods produce better results. A fine-tuned analysis of the power spectral density is very precise and shows how the different surface generation algorithms deviate from ideal fractal behaviour. For large datasets defined on equidistant two-dimensional grids, it is clearly the most sensitive and precise method to determine fractal dimension.
- 28 March 2023
- Published by Elsevier in International Journal of Plasticity
- Vol. 164
Dislocation pileups in small grains
- 28 March 2023
- Published by Elsevier in International Journal of Plasticity
- Vol. 164
Dislocation pileups in small grains
- Open Access
Surface Nanostructuring of a CuAlBe Shape Memory Alloy Produces a 10.3 ± 0.6 GPa Nanohardness Martensite Microstructure
Severe plastic deformation (SPD) has led to the discovery of ever stronger materials, either by bulk modification or by surface deformation under sliding contact. These processes increase the strength of an alloy through the transformation of the deformation substructure into submicrometric grains or twins. Here, surface SPD was induced by plastic deformation under frictional contact with a spherical tool in a hot rolled CuAlBe-shape memory alloy. This created a microstructure consisting of a few course martensite variants and ultrafine intersecting bands of secondary martensite and/or austenite, increasing the nanohardness of hot-rolled material from 2.6 to 10.3 GPa. In as-cast material the increase was from 2.4 to 5 GPa. The friction coefficient and surface damage were significantly higher in the hot rolled condition. Metallographic evidence showed that hot rolling was not followed by recrystallisation. This means that a remaining dislocation substructure can lock the martensite and impedes back-transformation to austenite. In the as-cast material, a very fine but softer austenite microstructure was found. The observed difference in properties provides an opportunity to fine-tune the process either for optimal wear resistance or for maximum surface hardness. The modified hot-rolled material possesses the highest hardness obtained to date in nanostructured non-ferrous alloys.
Open AccessSurface Nanostructuring of a CuAlBe Shape Memory Alloy Produces a 10.3 ± 0.6 GPa Nanohardness Martensite Microstructure
Severe plastic deformation (SPD) has led to the discovery of ever stronger materials, either by bulk modification or by surface deformation under sliding contact. These processes increase the strength of an alloy through the transformation of the deformation substructure into submicrometric grains or twins. Here, surface SPD was induced by plastic deformation under frictional contact with a spherical tool in a hot rolled CuAlBe-shape memory alloy. This created a microstructure consisting of a few course martensite variants and ultrafine intersecting bands of secondary martensite and/or austenite, increasing the nanohardness of hot-rolled material from 2.6 to 10.3 GPa. In as-cast material the increase was from 2.4 to 5 GPa. The friction coefficient and surface damage were significantly higher in the hot rolled condition. Metallographic evidence showed that hot rolling was not followed by recrystallisation. This means that a remaining dislocation substructure can lock the martensite and impedes back-transformation to austenite. In the as-cast material, a very fine but softer austenite microstructure was found. The observed difference in properties provides an opportunity to fine-tune the process either for optimal wear resistance or for maximum surface hardness. The modified hot-rolled material possesses the highest hardness obtained to date in nanostructured non-ferrous alloys.