Carlos Gabriel Figueroa
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Carlos Gabriel Figueroa has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
- Rafael Schouwenaars
Universidad Nacional Autónoma de México
8 shared publications - Víctor Hugo Jacobo
Universidad Nacional Autónoma de México
5 shared publications A. Ortiz
4 shared publicationsRafael Schouwenaars
4 shared publicationsArmando Ortiz
Universidad Nacional Autónoma de México
3 shared publicationsLeo Kestens
3 shared publications
Latest Publications
- Open Access
- 21 August 2025
- Published by IOP Publishing in Engineering Research Express
- Vol. 7 (3)
New formulation to characterize chip behaviour during metal cutting process
In this study, the behaviour of a chip during metal cutting processes is analysed using the analogy that the chip behaves mechanically like a beam. This representation simplifies the modelling of the machining process and is used to perform an analysis through basic physical concepts, representing the chip as cyclical formations of small beams, instead of relying on statistical regressions and adjustments that require experimental data. The force components exerted on the chip were determined via Merchant’s force circle. These forces create compression and cause bending, inducing fractures between the work material and the layer to be removed, which shapes and subsequently deforms the chip. Initially, the chip is approximated as a Euler–Bernoulli beam, enabling the quantification of the chip fragment’s length, as well as the forces and deformations involved in its formation. The model results were compared with those from trials reported in the literature, and an excellent approximation was achieved.
- 21 August 2025
- Published by IOP Publishing in Engineering Research Express
- Vol. 7 (3)
Open AccessNew formulation to characterize chip behaviour during metal cutting process
In this study, the behaviour of a chip during metal cutting processes is analysed using the analogy that the chip behaves mechanically like a beam. This representation simplifies the modelling of the machining process and is used to perform an analysis through basic physical concepts, representing the chip as cyclical formations of small beams, instead of relying on statistical regressions and adjustments that require experimental data. The force components exerted on the chip were determined via Merchant’s force circle. These forces create compression and cause bending, inducing fractures between the work material and the layer to be removed, which shapes and subsequently deforms the chip. Initially, the chip is approximated as a Euler–Bernoulli beam, enabling the quantification of the chip fragment’s length, as well as the forces and deformations involved in its formation. The model results were compared with those from trials reported in the literature, and an excellent approximation was achieved.
- Open Access
Influence of heat treatment on the wear behavior of an Al-Cu-Mg-Sn MMC reinforced with TiB2
- 12 March 2024
- Published by Elsevier in Journal of Molecular Structure
- Vol. 1308
Chemical and thermal stability of novel phenyl-BODIPY symmetric dimer thin films
- 12 March 2024
- Published by Elsevier in Journal of Molecular Structure
- Vol. 1308
Chemical and thermal stability of novel phenyl-BODIPY symmetric dimer thin films
- Open Access
- 7 March 2024
- Published by MDPI AG in Fractal and Fractional
- Vol. 8 (3) , 152
Statistical Study of the Bias and Precision for Six Estimation Methods for the Fractal Dimension of Randomly Rough Surfaces
The simulation and characterisation of randomly rough surfaces is an important topic in surface science, tribology, geo- and planetary sciences, image analysis and optics. Extensions to general random processes with two continuous variables are straightforward. Several surface generation algorithms are available, and preference for one or another method often depends on the specific scientific field. The same holds for the methods to estimate the fractal dimension D. This work analyses six algorithms for the determination of D as a function of the size of the domain, variance, and the input value for D, using surfaces generated by Fourier filtering techniques and the random midpoint displacement algorithm. Several of the methods to determine fractal dimension are needlessly complex and severely biased, whereas simple and computationally efficient methods produce better results. A fine-tuned analysis of the power spectral density is very precise and shows how the different surface generation algorithms deviate from ideal fractal behaviour. For large datasets defined on equidistant two-dimensional grids, it is clearly the most sensitive and precise method to determine fractal dimension.
- 7 March 2024
- Published by MDPI AG in Fractal and Fractional
- Vol. 8 (3) , 152
Open AccessStatistical Study of the Bias and Precision for Six Estimation Methods for the Fractal Dimension of Randomly Rough Surfaces
The simulation and characterisation of randomly rough surfaces is an important topic in surface science, tribology, geo- and planetary sciences, image analysis and optics. Extensions to general random processes with two continuous variables are straightforward. Several surface generation algorithms are available, and preference for one or another method often depends on the specific scientific field. The same holds for the methods to estimate the fractal dimension D. This work analyses six algorithms for the determination of D as a function of the size of the domain, variance, and the input value for D, using surfaces generated by Fourier filtering techniques and the random midpoint displacement algorithm. Several of the methods to determine fractal dimension are needlessly complex and severely biased, whereas simple and computationally efficient methods produce better results. A fine-tuned analysis of the power spectral density is very precise and shows how the different surface generation algorithms deviate from ideal fractal behaviour. For large datasets defined on equidistant two-dimensional grids, it is clearly the most sensitive and precise method to determine fractal dimension.
- 17 August 2022
- Published by Elsevier in Tribology International
- Vol. 175
Effect of heat treatment on friction and tribolayer formation in copper
- 17 August 2022
- Published by Elsevier in Tribology International
- Vol. 175
Effect of heat treatment on friction and tribolayer formation in copper
- 17 August 2022
- Published by Elsevier in Engineering Failure Analysis
- Vol. 141
Stress corrosion cracking of the slip-ring connectors of a 2 MW wind turbine
- 17 August 2022
- Published by Elsevier in Engineering Failure Analysis
- Vol. 141
Stress corrosion cracking of the slip-ring connectors of a 2 MW wind turbine
- 1 May 2021
- Published by Pleiades Publishing Ltd in Physics of Metals and Metallography
- Vol. 122 (5) , 504-514
Effect of the Repetitive Corrugation and Straightening on the Microstructure and Mechanical Properties of a 3003 Aluminum Alloy
A novel repetitive corrugation and straightening (RCS) die geometry was evaluated in terms of its mechanical properties and microstructural modifications. An annealed 3003 aluminum alloy sheet was processed up to 6 RCS passes at room temperature, showing a significant improvement in yield strength and hardness. Changes in surface profile values were obtained along different stages of the repetitive process; this showed a clear correlation between the higher strained region and the maxima of hardness values. Moreover, differences in roughness were associated with real contact area between material and corrugating die sections. Local strain distribution generated during the process was determined by kernel average misorientation (KAM) and was consistent with microhardness mapping results. Orientation image mapping showed that grains, with the normals parallel to 〈111〉, activate dislocation arrangement and grain fragmentation process prior to other main directions. In spite of mechanical properties improvement, initial texture components were maintained.
- 1 May 2021
- Published by Pleiades Publishing Ltd in Physics of Metals and Metallography
- Vol. 122 (5) , 504-514
Effect of the Repetitive Corrugation and Straightening on the Microstructure and Mechanical Properties of a 3003 Aluminum Alloy
A novel repetitive corrugation and straightening (RCS) die geometry was evaluated in terms of its mechanical properties and microstructural modifications. An annealed 3003 aluminum alloy sheet was processed up to 6 RCS passes at room temperature, showing a significant improvement in yield strength and hardness. Changes in surface profile values were obtained along different stages of the repetitive process; this showed a clear correlation between the higher strained region and the maxima of hardness values. Moreover, differences in roughness were associated with real contact area between material and corrugating die sections. Local strain distribution generated during the process was determined by kernel average misorientation (KAM) and was consistent with microhardness mapping results. Orientation image mapping showed that grains, with the normals parallel to 〈111〉, activate dislocation arrangement and grain fragmentation process prior to other main directions. In spite of mechanical properties improvement, initial texture components were maintained.
- Open Access
Surface Nanostructuring of a CuAlBe Shape Memory Alloy Produces a 10.3 ± 0.6 GPa Nanohardness Martensite Microstructure
Severe plastic deformation (SPD) has led to the discovery of ever stronger materials, either by bulk modification or by surface deformation under sliding contact. These processes increase the strength of an alloy through the transformation of the deformation substructure into submicrometric grains or twins. Here, surface SPD was induced by plastic deformation under frictional contact with a spherical tool in a hot rolled CuAlBe-shape memory alloy. This created a microstructure consisting of a few course martensite variants and ultrafine intersecting bands of secondary martensite and/or austenite, increasing the nanohardness of hot-rolled material from 2.6 to 10.3 GPa. In as-cast material the increase was from 2.4 to 5 GPa. The friction coefficient and surface damage were significantly higher in the hot rolled condition. Metallographic evidence showed that hot rolling was not followed by recrystallisation. This means that a remaining dislocation substructure can lock the martensite and impedes back-transformation to austenite. In the as-cast material, a very fine but softer austenite microstructure was found. The observed difference in properties provides an opportunity to fine-tune the process either for optimal wear resistance or for maximum surface hardness. The modified hot-rolled material possesses the highest hardness obtained to date in nanostructured non-ferrous alloys.
Open AccessSurface Nanostructuring of a CuAlBe Shape Memory Alloy Produces a 10.3 ± 0.6 GPa Nanohardness Martensite Microstructure
Severe plastic deformation (SPD) has led to the discovery of ever stronger materials, either by bulk modification or by surface deformation under sliding contact. These processes increase the strength of an alloy through the transformation of the deformation substructure into submicrometric grains or twins. Here, surface SPD was induced by plastic deformation under frictional contact with a spherical tool in a hot rolled CuAlBe-shape memory alloy. This created a microstructure consisting of a few course martensite variants and ultrafine intersecting bands of secondary martensite and/or austenite, increasing the nanohardness of hot-rolled material from 2.6 to 10.3 GPa. In as-cast material the increase was from 2.4 to 5 GPa. The friction coefficient and surface damage were significantly higher in the hot rolled condition. Metallographic evidence showed that hot rolling was not followed by recrystallisation. This means that a remaining dislocation substructure can lock the martensite and impedes back-transformation to austenite. In the as-cast material, a very fine but softer austenite microstructure was found. The observed difference in properties provides an opportunity to fine-tune the process either for optimal wear resistance or for maximum surface hardness. The modified hot-rolled material possesses the highest hardness obtained to date in nanostructured non-ferrous alloys.
- 13 June 2019
- Published by Springer Nature
- p. 162-168
Parametric Study of Simulated Randomly Rough Surfaces Used in Contact Mechanics
- 13 June 2019
- Published by Springer Nature
- p. 162-168
Parametric Study of Simulated Randomly Rough Surfaces Used in Contact Mechanics
- 15 July 2018
- Published by Springer Nature
- p. 500-511
Critical Analysis of Randomly Rough Surfaces for Contact Mechanics Through Statistical Simulation
- 15 July 2018
- Published by Springer Nature
- p. 500-511
Critical Analysis of Randomly Rough Surfaces for Contact Mechanics Through Statistical Simulation