SMSebastian Müller

Sebastian Müller

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Sebastian Müller has a total of 21 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    On the cryogenic treatment of austempered grey cast iron

    by Oliver Schenk, Fabian Teichmann, Sebastian Müller, Christoph Broeckmann

  • Open Access

    Local Induction Melting Combined with Ultrasonic Melt Treatment: A Pilot Study on Porosity, Mechanical Properties, and Energy Efficiency in AlSi12 Castings

    by Serouj Djabraian, Johannes Dettelbacher, Alexander Buchele, Fabian Teichmann, Sebastian Müller

    Light metal foundries consume large amounts of energy and rely mainly on gas-fired melting, which is inefficient and promotes porosity caused by dissolved hydrogen. This pilot study examines local induction melting combined with ultrasonic melt treatment (UST) as a decentralized and electrified alternative. AlSi12 was cast with varied mold temperature, casting temperature, UST duration and remelted fraction. Porosity was characterized by optical microscopy in 2D and, for a subset of specimens, by X-ray computed tomography in 3D, and the mechanical behavior by tensile testing. An experimentally benchmarked simulation was used to estimate the energy demand for larger batch sizes. Including the energy required for cooling, the measured laboratory efficiency was 7.9% to 14.9%, and the simulation predicts 41.3% for 100 kg, or 48% with a preheated crucible, against 53.1% derived for industrial induction furnaces. Specimens treated with UST showed a lower mean porosity, 0.56% against 2.14% in optical microscopy and 0.153% against 0.367% in computed tomography, where the pore count was 73% lower at almost unchanged pore size. Their mean strain at fracture was 45.5% higher and their mean toughness 53.2% higher, whereas the 4.4% higher mean tensile strength lies within the scatter of the measurements.

  • Open Access

    A Fourier-graph neural operator for transient isothermal two-phase mold filling relevant to metal casting

    by Edgard Moreira Minete, Mathis Immertreu, Fabian Teichmann, Sebastian Müller

  • Open Access

    On the Cryogenic Treatment of Austempered Grey Cast Iron

    by Oliver Schenk, Fabian Teichmann, Sebastian Müller, Christoph Broeckmann

    Grey cast iron is a common, cost-efficient engineering material used in a wide range of technical applications due to its favourable mechanical properties including good wear resistance and high compressive strength. This investigation focuses on the development of a novel combination of austempering and cryogenic treatment of lamellar cast iron, aiming to enhance its mechanical properties. For this purpose, two materials with differing chemical compositions were casted as Y-block specimens and were subjected to austempering at five different temperatures followed by a cryogenic treatment. The microstructure, the graphite morphology, the hardness and the compressive strength of all specimens were investigated systematically. For the first material, a notable increase of hardness and compressive yield limit by approximately 50% respectively 60% compared to the as-cast condition was found, which is attributed to the presence of newly formed martensite. This was consistently proven by dilatometry, Electron Backscatter Diffraction (EBSD) and Transmission Kikuchi Diffraction (TKD), with the latter revealing martensitic regions being located close to phosphides and acicular ferrite. Contrarily, the second material exhibits a negligible effect by cryogenic treatment, which is attributed to a finer austenitic grain size, which suppresses the phase transformation.

  • Open Access

    An Initial Study of Ultra High Performance Concrete as Reusable Mold Material for Aluminum Casting

    by Janna Link, Fabian Teichmann, Alexander Wetzel, Sebastian Müller, Bernhard Middendorf

    The initial investigation evaluates the feasibility of ultra high performance concrete (UHPC) as a material for reusable molds in aluminum casting. Two specific UHPC formulations were investigated: one based on ordinary Portland cement (OPC) and another utilizing alkali-activated materials (AAM). The study focused on investigating the surface through roughness measurements and the thermal durability through repeated casting cycles. The thermal stability of the molds was investigated by thermogravimetric analysis, mercury intrusion porosimetry, crack segmentation, optical microscopy, and electron microscopy. Results indicate that molds fabricated from AAM-UHPC exhibit relatively better performance in terms of maintaining structural integrity and surface quality over repeated uses. AAM-UHPC molds were able to withstand up to ten casting cycles with acceptable surface degradation and no significant failure, while OPC-UHPC molds exhibited a faster degradation under similar conditions. Microstructural changes and the interaction of UHPC materials with molten aluminum were investigated, highlighting the low adhesion and defect formation. Additionally, the molds demonstrated sound casting quality, with a grain size comparable to that achieved using traditional steel molds (~ 90 µm), underscoring the potential of UHPC materials for enhancing casting quality and efficiency. The study concludes that UHPC, particularly with alkali-activated formulations, shows promise for low-pressure casting environments.


  • Open Access

    Thermo-Mechanical Optimization of Die Casting Molds Using Topology Optimization and Numerical Simulations

    by Serouj Djabraian, Fabian Teichmann, Sebastian Müller

    Conventional cooling channels used in die casting molds exhibit significant drawbacks, resulting in extended cooling times for cast parts. Issues such as the formation of dirt, limescale, and corrosion substantially diminish the thermal efficiency of these channels, leading to challenges in achieving uniform cooling and potential quality issues. In response to these challenges, this study proposes Topology Optimization as a novel approach. It involves designing cooling structures through Topology Optimization to replace traditional cooling channels, incorporating both Discrete and Gaussian boundary conditions to optimize thermal efficiency. Additionally, Structural Topology Optimization is employed to ensure structural integrity, preventing deformation or yielding under high loads during the die casting process. Numerical analysis revealed superior thermal performance compared to conventional channels, particularly when subjected to Discrete and Gaussian boundary conditions. Furthermore, the application of the latter establishes conformal cooling and minimizes temperature gradients in the casting, reducing casting defects such as shrinkage porosity. These findings highlight the efficacy of Topology Optimization in addressing the challenges of traditional cooling methods, with wide-ranging implications for manufacturing processes utilizing permanent molds for shaping materials.


  • Open Access

    The Costs of More Sustainable Castings Can we Afford the Change?

    by Lucas Pelchen, Sebastian Müller

    Rising costs for fossil fuels and the need to reduce emissions in the production of castings are subjecting foundries worldwide to increasing pressure to act and innovate. Due to fierce global competition in this sector and high investment costs for alternative technologies, foundries are therefore under high pressure to transform, while at the same time having limited financial resources. This article examines the economic and environmental differences between a conventional industrial foundry process chain, a process chain based on a hydrogen (H2)-fired melting furnace and an all-electric approach using conversion of H2 to electricity within a solid oxide fuel cell. To ensure an unbiased comparison of the process chains introduced, the respective mass efficiencies are first determined using an absorbing Markov chain before calculating the mass-specific costs and emissions of each approach using a literature-based process model. The comparison of the setups shows negligible differences in terms of material loss and cost in the respective best case. However, significantly higher emission minimums are found for both H2 approaches compared to the biogas-based conventional approach, especially for the use of green H2. In summary, no significant economic disadvantages of the H2-based approaches can be identified. Even considering that the economic comparison is biased in favor of biogas due to accounting measures, the environmental difference is comparatively small. The results indicate that the conversion of the foundry industry towards more sustainable H2-based foundry process chains is in principle reasonable as well as affordable and should therefore be achieved in the medium term.

  • Open Access

    A Near-Surface Layer Heat Treatment of Die Casting Dies by Means of Electron-Beam Technology

    by Torsten Schuchardt, Sebastian Müller, Klaus Dilger

    Increasing the service life of die casting dies is an important goal of the foundry industry. Approaches are either material- or process-related. Despite new material concepts, hot work steels such as H11 are still predominantly used in the uncoated condition for die casting dies. In order to withstand the stresses that occur, this steel is used exclusively in the quenched and tempered condition. Required properties such as high high-temperature strength and high hardness combined with high toughness are, in principle, contradictory and can only be adjusted consistently over the entire die by furnace-based heat treatment. However, the results of various investigations have shown that improvements in the thermal shock resistance and wear resistance of hot work tool steels can be achieved by thermally influencing the microstructure near the surface. Based on these studies and related findings, an approach to surface heat treatment using the electron beam was developed. Due to the particle character of the radiation and the associated possibility of high-frequency beam deflection, the electron beam offers significantly greater flexibility in energy input into the workpiece surface compared with lasers or induction. The overall technological concept envisages replacing furnace-based heat treatment in the production of casting dies by localized and demand-oriented boundary layer heat treatment with the electron beam. The experiments include, on the one hand, the experimental determination of a suitable temperature–time interval with a focus on short-term austenitization. On the other hand, a simulation-based approach of boundary layer heat treatment with validation of a suitable heat source is investigated. Regarding short-term austenitization, the corresponding temperature and time range could be narrowed down more precisely. Some of these parameter combinations seem to be very suitable for practical use. The test specimens show a hard surface layer with a depth of at least up to 6 mm and a very tough buffer layer. Numerical simulation is used to estimate the resulting metallurgical microstructure and the achievable hardness as a function of the temperature–time interval. In addition, the results provided show the possibility of determining and optimizing the material properties by means of a simulation-based approach within the framework of a purely digital process planning and subsequently transferring them into a process planning. In the technical implementation, a temperature control was first established by means of a two-color pyrometer. In the further course of research, the pyrometer will be supplemented by an internally installed infrared camera, which will allow the reproducible setting of specified temperature profiles even for complex, large-area contours in the future.