CGChangfeng Ge

Changfeng Ge

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Changfeng Ge has a total of 46 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Composite Analysis of Field Horizontal Long‐Duration Impacts for Truck and Trailer

    by Changfeng Ge, Kyle Dunno, David Leinberger, Patrick McDavid

    Long‐duration vehicle impact events are experienced during turning, braking, acceleration and deceleration. These events make unitized packaging susceptible to slip or tilt when the location of their centre of gravity changes. The large amount of field‐collected long‐duration data requires processing and composite analysis to develop a representative profile in order to replicate the long‐duration impact in the laboratory simulation. Based on the prior field data of long‐duration impact, this study introduces composite analysis for the collected data emphasizing on the maximum acceleration and the maximum equivalent velocity change. The shock response spectrum (SRS) of these maximum impact events is also studied for identifying the possible amplification frequency. The field data generated composite profiles in the lateral and longitudinal directions were compared with EUMOS's lateral/rearward and deceleration orientations, respectively.


  • Measuring and Assessing Long‐Duration Impacts for Truck and Trailer

    by Changfeng Ge, David Leinberger, Kyle Dunno

    A vehicle's long‐duration impacts events are experienced during turning, braking, and accelerating and decelerating. These long‐duration events are mixed with random impacts and shocks from various patterns and magnitudes. This study reports a comprehensive measurement and assessment of horizontal long‐duration impact dynamics for less‐than‐truckload (LTL) transportation. The collected horizontal impacts were synchronized with GPS data, allowing for the geographical location and identification of the event's signatures. All critical horizontal long‐duration impacts were detected by a MATLAB‐based algorithm and clustered into designated groups. A maximum collected environment and statistical analysis were assessed for the collected data, including the range, mean and cumulative probabilities. The study revealed that horizontal impacts caused by left‐turning and longitudinal braking are likely the most critical horizontal impacts. Additionally, lateral and longitudinal linear jerks were obtained for comparison with the EUMOS standard.


  • Exploring factors affecting the conversion of the coefficient of restitution to equivalent free fall drop height

    by Kang Lin, Changfeng Ge, Jing Qian, Tao Guo, Sixuan Xia

    The coefficient of restitution (COR) is used to estimate the equivalent free fall drop height of packaging during handling and transportation. Various experimental studies were designed to explore factors affecting the conversion of the COR to equivalent free fall drop height. These factors include the number of drops, drop height, drop orientation, drop base, temperature and humidity on the COR. The results indicate that the number of drops and drop orientation are the two most influential factors affecting COR values. As the package undergoes more drops, the COR increases. Among the various orientations, the COR is largest for flat drops, followed by edge and corner orientations. Within flat drops, a smaller impact area results in a smaller COR. Manufacturing joints and the flats, edges and corners adjacent to manufacturing joints tend to yield smaller COR values. A COR correction matrix was developed to correct the conventional COR calculation. This matrix allows engineers to refine COR values based on the number of drops and drop orientations in the field. The matrix‐corrected equivalent free fall drop heights demonstrated an average accuracy of 96%. Compared to the conventional COR calculation method, it effectively reduces errors by a factor of 2–3.


  • A review and update of the corrugated fibreboard cushioning

    by Changfeng Ge

    The corrugated fibreboard was the dominated cushioning material before the advent of expanded plastic foams in the 1960s. With recent advances in packaging sustainability, the corrugated pads are again the research focus. This paper reviewed studies of corrugated fibreboard cushioning in areas of design and experimental evaluation. Since most of these research works were performed more than half a century ago, the historical data were reexamined and compared with the current practices. Previous and recent structure designs, represented by layered corrugated pads, tube, spring and zig‐zag components, were displayed and discussed. This study also reviewed studies investigating the crush resistance and cushion curves in hope to provide some practical guidance on prediction of cushioning performance. As an updated development by the author, this study presented cushion curves developed under three loading patterns, namely, column, underhang and overhang. Finally, the study pointed out that double dipping points and shift‐to‐right tendency on the cushion curves, as well as the long plateau on the stress–strain curves, are unique properties of corrugated fibreboard cushioning. Packaging engineers are suggested to factor in these properties in design for different applications.


  • Field assessment of horizontal accelerations using air ride suspension trailers

    by Kyle Dunno, Changfeng Ge

    Current laboratory tests designed to evaluate package and unit load systems focus strictly on the intensity of vertical orientation. However, due to an increased demand for source reduction and the light‐weighting of packaging components, unit loads are becoming more susceptible to the horizontal forces encountered during transport. Understanding the field measured acceleration levels is critical to developing accurate laboratory test simulations to examine unit load rigidity. This paper uses horizontal acceleration data collected from two air ride suspension trailers to quantify the rise times and steady‐state accelerations levels experienced by the vehicles in the longitudinal (braking) and lateral directions. These characteristics are essential in establishing test methods that accurately reflect field measured events. The results show that the rise times experienced by larger transport trailers are longer than previous reports using smaller trailers. The larger transport vehicles from the present study showed lower decelerations and accelerations in braking and lateral moving events, respectively, compared to smaller transport vehicles. Regardless of travel direction, the deceleration and acceleration levels are right‐skewed, with most of the events falling below 0.33 g.


  • Open Access

    Development of a Drone’s Vibration, Shock, and Atmospheric Profiles

    by Changfeng Ge, Kyle Dunno, Mukul Anand Singh, Long Yuan, Li-Xin Lu

    Technological advances in unmanned aerial vehicles (UAVs) have made it possible to employ drone deliveries for packaged products, but currently no standards of practice are available to qualify packaged products traveling through this distribution channel. This research proposes a methodology to collect field data from a UAV to develop simulation techniques for use with package testing equipment. This project utilized data recorders to measure the vibration, shock, and atmospheric field data on two models of the DJI drones. The root mean square G value (Grms), the power spectral density (PSD), maximum G-values and shock response spectrum, and atmospheric data were reported in this study. The study found that the general shape of the PSD profile of the drones differed from the PSD air profiles of the aircraft. The overall recorded Grms levels of the drones were also significantly higher than those of the published air profile of the aircraft. Moreover, the study found that the drone’s in-flight vibration intensities in the horizontal level were consistently higher than those in the vertical direction. The major sources of vibration and shock in both drones’ models originated from the two-propeller rotations. Shocks recorded during the flight reached 14 G, took place in the horizontal plane with the drone accelerating as opposed to the vertical plane where the drone is landing.


  • Characterization of low‐acceleration, long‐duration horizontal events using a spring suspension straight delivery box truck

    by Kyle Dunno, Changfeng Ge

    A field measurement study, using a combination of controlled and uncontrolled phases, examined low‐acceleration, long‐duration events occurring during over‐the‐road truck transport. A field data recorder equipped with a DC‐based triaxial accelerometer was employed for this study to capture the steady‐state nature of these event types. The field data recorder was rigidly mounted to the trailer chassis to record lateral and longitudinal events of interest. The controlled phase recorded normal and aggressive braking events and traversing a roundabout to fundamentally quantify the behaviour of the vehicle. For the controlled phase, average decelerations of 0.27 and 0.45 g were reported for normal and aggressive braking events, respectively. Lateral accelerations from traversing a roundabout were on average 0.40 g. The uncontrolled field measurement study, which evaluated the transport vehicle over 13 days, reported average longitudinal decelerations and lateral accelerations of 0.29 and 0.34 g, respectively. The rise times associated with these events were also reported. The jerk was calculated based on the rise times for the controlled and uncontrolled phases and compared to currently available test procedures. For both project phases, composite test profiles were developed based on field‐measured levels. The resulting composite test profiles can be utilized to evaluate the load stability of a unit load system travelling through this distribution channel.


  • Effects of flexing, optical density, and lamination on barrier and mechanical properties of metallized films and aluminum foil centered laminates prepared with polyethylene terephthalate and linear low density polyethylene

    by Changfeng Ge, Suraj Singh Verma, Jack Burruto, Nazar Ribalco, Janice Ong, K Sudhahar

    Flex barrier and optical density (OD) are two unique properties for metallized films and aluminum foil. This study investigated the effect of flexing on barrier properties of a laminate comprising metallized films and aluminum foil, as well as OD and adhesive lamination process on the overall multilayer laminate performance. Three (3) barrier layers, namely aluminum foil, metallized polyethylene terephthalate (met OPET) film with a high OD, and standard metallized PET film(met OPET), were laminated with the same printing layer OPET and sealing layer linear low density polyethylene (LLDPE), into OPET/adhesive/foil/adhesive/LLDPE and OPET/adhesive/met OPET/adhesive/LLDPE structures. The oxygen transmission rate (OTR) and water vapor transmission rate (WVTR) were measured before and after flexing. The aluminum foil centered laminate had an excellent oxygen barrier after the 20-cycle flexing test and failed to retain its oxygen barrier after the 270-cycle flexing. Compared to the aluminum foil centered laminate, the metallized film centered laminates were less affected by the flexing on the oxygen barrier. For all laminates, the water vapor barrier was less severely affected by flexing than the oxygen barrier. This study suggests that the ASTMF392 Gelbo D (20- cycle flexing) can determine if aluminum foil and metallized film centered laminates are resistant to flex-formed pinhole failures. A higher OD, a thicker film thickness and lamination process improved laminate’s actual barrier, resulting in lower measured transmission rates versus that predicted using Henry's solubility law and Fick's diffusion law. The laminate’s water vapor transmission rate is 55–74% lower than predicted. The oxygen transmission rate is 15–31% lower than predicted.