Irina I. Kurkina has a total of 46 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Electrical Properties of Structures Based on Two-Dimensional Molybdenum Disulfide

    by P. V. Vinokurov, A. A. Alexeev, I. I. Kurkina, S. A. Smagulova

    The electrical characteristics of molybdenum disulfide films synthesized by CVD from powder precursors MoO3 and S were studied. Silver contacts were used to measure the current–voltage characteristics of MoS2 films deposited on SiO2/Si substrates. The dependence of the properties of the Ag/MoS2 contact on the number of MoS2 film layers was discovered. For multilayer molybdenum disulfide films, an ohmic contact is formed between silver and MoS2, while for few-layer films, a Schottky barrier is formed. From the temperature dependences of the current–voltage characteristics, the activation energies of conductivity were calculated to be 0.26 and 0.22 eV for two-layer and three-layer MoS2 films, respectively. For single-layer MoS2 films, the current–voltage characteristics showed the presence of a resistive switching effect. Using the deep-level charge spectroscopy (Q-DLTS) method, a level of 0.20 eV below the conduction band was found in MoS2 films. Based on the vertical van der Waals heterostructure of graphene/MoS2/Si, a solar cell was created that can generate a voltage of 0.48 V when illuminated by a halogen lamp.

  • Open Access

    ФОРМИРОВАНИЕ ЗАЩИТНОЙ УГЛЕРОДНОЙ ПЛЕНКИ НА ПО-ВЕРХНОСТИ ГРАФЕНА МЕТОДОМ ПЛАЗМЕННОГО ОСАЖДЕНИЯ И ТЕРМООБРАБОТКИ

    by Ефим Петрович Неустроев, Ирина Ивановна Куркина, Данил Валериевич Николаев

    Предложена методика формирования защитного углеродного слоя для графеновых пленок на основе двухстадийного процесса, включающего осаждение атомов углерода в плазме метана и термообработку. Для осаждения атомов углерода использован радиочастотный индуктивно связанный источник плазмы мощностью 200 Вт. Длительность процесса осаждения в плазме метана составляло от 3 до 6 мин. Термообработки проведены в атмосфере инертного газа при температурах от 750 оС до 800 оС длительностью до 25 мин. Для характеризации поверхности использованы методы атомной силовой микроскопии и спектроскопии комбинационного рассеяния света. Исследования методом атомно-силовой микроскопии показали, что предложенная методика позволяет успешно формировать углеродные пленки толщиной несколько десятков нанометров на поверхности исходной графеновой пленки, полученной методом газофазового осаждения. После травления в плазме кислорода мощностью 200 Вт и длительностью до 30 с синтезированнной структуры формируются пленки нанометровых толщин с шероховатостью поверхности около 0,5 нм. Наблюдаемые в исходной графеновой пленке складки высотой от единиц до десятков нанометров на поверхности сформированных образцов не обнаружены. Из анализа спектров комбинационного рассеяния света следует, что после травления в плазме кислорода синтезированных структур до исходных толщин графеновых пленок имеет место восстановление основных графеновых G- и 2D-пиков в спектрах. Можно отметить некоторое возрастание интегральной интенсивности D-полосы, обусловленной наличием дефектов и нарушений в кристаллической решетке, которое частично может быть устранено термической обработкой.

  • Open Access

    Rapid synthesis of CVD graphene with controllable charge carrier mobility

    by Maxim G. Rybin, Evgeniy A. Guberna, Ekaterina A. Obraztsova, Ivan Kondrashov, Irina I. Kurkina, Svetlana A. Smagulova, Elena D. Obraztsova


  • Thin V2O5 films synthesized by plasma-enhanced atomic layer deposition for memristive applications

    by Irina V. Antonova, Vladimir A. Seleznev, Nadezhda A. Nebogatikova, Artem I. Ivanov, Bogdan V. Voloshin, Vladimir A. Volodin, Irina I. Kurkina

    V2O5/Si structures with an average V2O5 thickness of 1.0–3.6 nm and orthorhombic phase demonstrate stable memristive switching with an ON/OFF ratio ∼1–4 orders of magnitude.


  • Graphene/Hexagonal Boron Nitride Composite Nanoparticles for 2D Printing Technologies

    by Irina V. Antonova, Marina B. Shavelkina, Dmitriy A. Poteryaev, Nadezhda A. Nebogatikova, Artem I. Ivanov, Regina A. Soots, Anton K. Gutakovskii, Irina I. Kurkina, Vladimir A. Volodin, Vladimir A. Katarzhis, et al.

    A new approach for creating composite nanoparticles with various morphology and electric properties, based on uniform‐sized small boron nitride (h‐BN) nanosheets and graphene flakes, is suggested. For the first time, the structures from h‐BN and graphene flakes synthesized in the helium direct current plasma jet are used to fabricate composite nanoparticles and films using 2D printing technology. A method for preparing a suspension based on these composite particles is developed. The morphology of graphene decoration with small h‐BN flakes depends on the composite content. It includes, for instance, graphene flakes covered with vertically arranged h‐BN flakes, graphene flakes encapsulated with a monolayer of h‐BN flakes. The electric properties of films and printed structures from composite nanoparticles are strongly varied (especially for the printed compositions). However, the graphene content in all cases is higher than the percolation threshold. Some composites demonstrate nonlinear current–voltage characteristics with the switching up to four orders of magnitude. In combination with the cheap printed technologies, the composite material is expected to be a perspective for electronic applications (informative processing, logic elements, tunneling graphene electronics, memristors, etc.).


  • Open Access

    Flexibility of Fluorinated Graphene-Based Materials

    by Irina Antonova, Nadezhda Nebogatikova, Nabila Zerrouki, Irina Kurkina, Artem Ivanov

    The resistivity of different films and structures containing fluorinated graphene (FG) flakes and chemical vapor deposition (CVD)-grown graphene of various fluorination degrees under tensile and compressive strains due to bending deformations was studied. Graphene and multilayer graphene films grown by means of the chemical vapor deposition (CVD) method were transferred onto the flexible substrate by laminating and were subjected to fluorination. They demonstrated a weak fluorination degree (F/C lower 20%). Compressive strains led to a strong (one-two orders of magnitude) decrease in the resistivity in both cases, which was most likely connected with the formation of additional conductive paths through fluorinated graphene. Tensile strain up to 3% caused by the bending of both types of CVD-grown FG led to a constant value of the resistivity or to an irreversible increase in the resistivity under repeated strain cycles. FG films created from the suspension of the fluorinated graphene with a fluorination degree of 20–25%, after the exclusion of design details of the used structures, demonstrated a stable resistivity at least up to 2–3% of tensile and compressive strain. The scale of resistance changes ΔR/R0 was found to be in the range of 14–28% with a different sign at the 10% tensile strain (bending radius 1 mm). In the case of the structures with the FG thin film printed on polyvinyl alcohol, a stable bipolar resistive switching was observed up to 6.5% of the tensile strain (bending radius was 2 mm). A further increase in strain (6.5–8%) leads to a decrease in ON/OFF current ratio from 5 down to 2 orders of magnitude. The current ratio decrease is connected with an increase under the tensile strain in distances between conductive agents (graphene islands and traps at the interface with polyvinyl alcohol) and thickness of fluorinated barriers within the active layer. The excellent performance of the crossbar memristor structures under tensile strain shows that the FG films and structures created from suspension are especially promising for flexible electronics.


  • Negative differential resistance in partially fluorinated graphene films

    by I. V. Antonova, S. Shojaei, S. M. Sattari-Esfahlan, Irina I. Kurkina

    Partially fluorinated graphene films were created by chemical functionalization of graphene layers in an aqueous solution of hydrofluoric acid. The formation of graphene islands or graphene quantum dots (GQDs) and a fluorinated graphene network is demonstrated in such films. Negative differential resistance (NDR) resulting from the formation of the potential barrier system in the films was observed for different fluorination degrees of suspension. The origin of the NDR varies with an increase in the fluorination degree of the suspension. Numerical calculations were performed to elucidate the tunneling between adjacent energy levels and creation of NDR. It was found that in the case of films with smaller flake and smaller GQD sizes, multi-peak NDR appears in the I–V curve. We predict that the NDR peak position shifts towards lower voltage with a decrease in the GQD size. Surprisingly, we observed a negative step-like valley for positive biases in the I-V curve of samples. Our findings with detailed analysis shed light on understanding the mechanisms of the NDR phenomenon in a partially fluorinated graphene system.


  • Films fabricated from partially fluorinated graphene suspension: structural, electronic properties and negative differential resistance

    by Irina V Antonova, Irina I Kurkina, Nadezhda A Nebogatikova, Alexander I Komonov, Svetlana A Smagulova

    The band structure and electric properties of films created from a partially fluorinated graphene suspension are analyzed in this paper. As may be inferred from the structural study, graphene islands (quantum dots) are formed in these films. Various types of negative differential resistance (NDR) and a step-like increase in the current are found for films created from the fluorinated graphene suspension. NDR resulting from the formation of the potential barrier system in the film and corresponding to the theoretical prediction is observed for a relatively low fluorination degree. The origin of the NDR varies with an increase in the fluorination degree of the suspension. The observation of NDR in the fluorinated films widens the range of application of such films, including as active device layers fabricated using 2D printed technologies on rigid and flexible substrates.


  • Fluorinated graphene suspension for inkjet printed technologies

    by N A Nebogatikova, I V Antonova, I I Kurkina, R A Soots, V I Vdovin, V B Timofeev, S A Smagulova, V Ya Prinz

    The possibility to control the size of the flakes of graphene suspension in the course of their fluorination in an aqueous hydrofluoric acid solution was demonstrated. The effect of the suspension composition, the fluorination time, temperature and thermal stress on the fragmentation process was investigated. The corrugation of suspension flakes, which occurs at fluorination due to a difference in the constants of graphene and fluorographene lattices, leads to the appearance of nonuniform mechanical stresses. The fact that the flake size after fragmentation is determined by the size of corrugation allows the assumption that the driving force of fragmentation is this mechanical stress. This assumption is confirmed by the break of the corrugated layers from flakes under thermal stress. Moreover, fluorination treatment at elevated temperatures (~70 °C) significantly accelerates the fragmentation process. Suspensions of fluorinated graphene with nanometer size flakes are of interest for the development of 2D ink-jet printing technologies and production of thermally and chemically stable dielectric films for nanoelectronics. The printed fluorinated graphene films on silicon and flexible substrates have been demonstrated and the charges in metal–insulator–semiconductor structures have been estimated as the ultra low values of (0.5–2) × 1010 cm−2.