Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Artem Ilyich Ivanov has a total of 68 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Ultra-thin graphene/PEDOT:PSS wearable sensor for human emotion diagnosis

    by Irina V. Antonova, Artem I. Ivanov, Anna A. Buzmakova, Olga P. Cherkasova, Marina B. Shavelkina

  • Conductive ultra-flexible graphene-based films for electronic applications

    by Nikolay V. Petyakin, Artem Ilyich Ivanov, Anna A. Buzmakova, Irina V. Antonova

    A graphene-based conductive material with the ability to maintain low resistivity under repeated large strains is proposed for flexible electronics applications.


  • Biosensors based on cellular components of cyanobacteria for monitoring technologies

    by M.B. Shavelkina, I.V. Antonova, N.A. Nebogatikova, A.I. Ivanov, S.V. Kiseleva, N.I. Chernova


  • High Sensitivity of Non-Invasive Glucose Sensors Made from Graphene-Based Composite Materials

    by I. V. Antonova, A. I. Ivanov, M. B. Shavelkina, A. A. Buzmakova, I. I. Kurkina

    The object of study was human sweat-based sensors printed on paper and spunlace nonwoven fabric using ink consisting of graphene and the conductive polymer PEDOT:PSS. In glucose identification, the 2D layers have demonstrated resistance decrease by three to five orders of magnitude. The influence of the printed layer structure on the sensor sensitivity has been established. A maximum sensitivity was observed for two to three printed layers, when most graphene flakes in the layers were located vertically and thus ensured presence of active states in the layer, at the flake boundaries. At elevated humidity, a spectrum of electrically active states appeared with a maximum at an energy of ~0.36–0.40 eV, and these electrically active states provided conductivity. It is assumed that adsorption of glucose molecules occurred on the edge states of graphene flakes, and they also acted as a catalyst for glucose oxidation. As a result, the conductivity increased sharply, depending on the additional carriers resulting from the glucose oxidation. The sharp decrease in the sensitivity and selectivity in thicker films of the same composite is associated with the change in the structure of the layers: there arise clusters of the material without free edge states of graphene flakes. The non-invasive sensors created combine ease of manufacture and low cost with high sensitivity.

  • Graphene-based multifunctional humidity sensors with an ultrahigh current response

    by Irina V. Antonova, Dmitriy A. Poteryayev, Artem I. Ivanov, Nadezhda A. Nebogatikova, Marina B. Shavelkina

    Prospective composites, based on graphene (G) and hexagonal boron nitride (h-BN) nanoparticles, synthesized using a plasma jet and conducting polymer PEDOT:PSS, were used to create and study a set of sensors in the current study. The composites used were G:PEDOT:PSS (GPP) and G:h-BN:PEDOT:PSS (GBNPP). The PEDOT:PSS content in the composites was 10−3 wt%, and the ratio of G : h-BN was 1 : 1 in GBNPP. The development of these new highly conductive graphene-based composites makes it possible to create an active sensor layer with an ultra-low thickness of several nanometers. The ultra-high sensitivity of the current response, S, was ((2.0–3.3) × 106)% for GPP and GBNPP (2–3 printing layers) for a humidity range of 20–80%. The sensor response in the form of current pulses associated with human breathing has a range of ∼2–3 orders of magnitude. Two different processes are assumed to determine the form of the current pulse: the first is a fast process with a rise time of less than 1–4 seconds; the second is a relatively slow process with a front time of several tens of seconds. When touching with a finger (useful, for instance, for a flexible touchpad), a current response was observed as pulses of ∼2–3 orders of magnitude. We hypothesize that skin sweat is likely to play a critical role in the sensory response. Thus, this work presents an effective approach to creating a highly sensitive humidity sensor based on composite 2D materials. Moreover, the ultra-high sensitivity of the studied sensors is accompanied by their low cost and ease of manufacturing by 2D-printing.


  • Thin V2O5 films synthesized by plasma-enhanced atomic layer deposition for memristive applications

    by Irina V. Antonova, Vladimir A. Seleznev, Nadezhda A. Nebogatikova, Artem I. Ivanov, Bogdan V. Voloshin, Vladimir A. Volodin, Irina I. Kurkina

    V2O5/Si structures with an average V2O5 thickness of 1.0–3.6 nm and orthorhombic phase demonstrate stable memristive switching with an ON/OFF ratio ∼1–4 orders of magnitude.


  • The Variation in Active Layer Resistance as a Way to Vary the Electrodynamic Characteristics of Graphene Antennas

    by Alexander G. Cherevko, Artem I. Ivanov, Irina V. Antonova

    Suppression of the first harmonic of graphene antenna radiation due to a significant change in the surface resistance of the conductive layers by changing layer thickness, was demonstrated in the present study. This effect makes it possible to govern the electrodynamic characteristics of antennas by changing the thickness of the printed conductive layer of the graphene antenna. This result supports the conclusion about the common positive effect of the variable resistivity of graphene antennas stated in [Perruisseau-Carrier, J. In: Proceedings of the LAPC, Loughborough, UK, 2012; pp. 1-4.]. The result was obtained on a symmetrical one-sided classical planar dipole on a substrate made of a foil-reinforced fluoroplastic FAF-4D, high-frequency dielectric widely used for GHz-band antennas. It has been confirmed for the frequency of the G band 5–5.2 GHz, both by simulation and experimentally for antennas of different thicknesses and different bending radii, and when printed with composite graphene ink.

  • Open Access

    First Experimental Demonstration of the Wide-Field Amplitude Surface Plasmon Resonance Microscopy in the Terahertz Range

    by Vasiliy Valerievich Gerasimov, Oleg Eduardovich Kameshkov, Alexey Konstantinovich Nikitin, Ildus Shevketovich Khasanov, Alexey Georgievich Lemzyakov, Irina Veniaminovna Antonova, Artem Ilyich Ivanov, Nghiem Thi Ha Lien, Nguyen Trong Nghia, Le Tu Anh, et al.

    We have demonstrated the wide-field amplitude surface plasmon resonance (SPR) microscopy technique in the terahertz (THz) range. A Zeonex polymer prism was utilized to excite surface plasmon polaritons (SPPs) through attenuated total reflection (ATR) in an Otto configuration. Coherent quasimonochromatic radiation with a wavelength of approximately 197 μm, generated by the Novosibirsk free electron laser, was employed. Our results indicate that the SPR microscopy method is applicable for investigating the planar surfaces of semiconductors at THz frequencies, provided that the SPPs’ cutoff frequency is close to the probing radiation frequency. This condition ensures that the propagation length of the SPPs is comparable to the radiation wavelength. By varying the air gap between the prism and the surface under examination, we acquired images of a polypropylene coating 20 µm thick and a graphene coating 35 nm thick on a flat indium antimonide substrate. The boundary between the coated and uncoated regions can be precisely localized through determination of the kink in the reflection coefficient of the THz radiation beam that illuminates the boundary between the regions if the optimal conditions for the generation of the SPPs in the uncoated region are met.


  • Engineering of graphene flakes in the process of synthesis in DC plasma jets

    by Irina V. Antonova, Marina B. Shavelkina, Artem I. Ivanov, Nadezhda A. Nebogatikova, Regina A. Soots, Vladimir A. Volodin

    During the pyrolysis of hydrocarbons in helium plasma jets in a plasma-chemical reactor, graphene flakes of a different structure and resistance were obtained. The presence of hydrogen in these structures was established by physicochemical methods, and its content depends on the pressure in the plasma-chemical reactor and the composition of a plasma-forming system. In addition to hydrogen, a relatively low concentration of oxygen atoms is present in the graphene flakes. Hydrogen is involved in the graphene nucleation, whereas oxygen is absorbed on graphene flakes from the air at low temperatures. It was found that a pressure increase in the reactor (up to 710 Torr) leads to the formation of flakes with a low resistivity (0.12–0.20 kOhm sq−1) and low defect density. In the case of synthesis at a low pressure (350–500 Torr), the resistance of graphene flakes is increased by three orders of magnitude (100–400 kOhm sq−1) with a more complicated defect structure and built-in hydrogen. Moreover, hydrogen is difficult to remove from these flakes, and annealing at relatively high temperatures (up to 300 °C) leads to a weak decrease in the resistance due to flake deformation. Additionally, the functionalization of the graphene flakes synthesized at a low pressure with fluorine atoms is suppressed due to their structural features. In general, the selection of growth parameters (gas pressure in a camera, flow rate and content of impurity atoms) allows one to control the defects in graphene, and its structure and conductivity.


  • Flexibility of fluorinated graphene based memristor structures: current flow model in a multi-barrier system under tensile strain

    by A I Ivanov, I V Antonova

    The flexibility of two types of memristor structures with fluorinated graphene (FG) based active layers (FG with graphene islands on polyvinyl alcohol, FG/PVA, and films from nanoparticles of V 2 O 5 capsulated with FG, FG/V 2 O 5 ) under the tensile strain in bending conditions was investigated and compared in the present study. Both types of memristors show a similar mechanism of resistance switchings (current paths on traps without filaments). Multi-barrier model of current flow was used to estimate the barrier parameters connected to FG from experiments on resistive switching of memristor structures in the bending condition. The first type of structures (Ag/FG/PVA/Ag) demonstrates the record high values of flexibility: ON/OFF current relation is not changed up to 7% tensile strain created by bending. The second type of structures (Gr/FG/V 2 O 5 /Gr with graphene contacts) show a decrease in ON current already for tensile strain more than 2%. The similar mechanism of current flow allows us to use the similar theory for description of the current flow versus the tensile strain. In spite of different structures and morphology of memristors, the typical values of the barrier height extracted from the theoretical description were similar: ∼1.5 eV with an effective barrier thickness of ∼16.5 nm and ∼1.3–1.6 eV with thickness 13.5–15.0 nm for FG/PVA and FG/V 2 O 5 structures, respectively. Increase in the barrier thickness over 19 nm in both cases leads to the strong decrease in ON current of memristors.