Shlomo Mehari
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Shlomo Mehari has a total of 41 co-authors. Here are the top co-authors by number of shared publications:
Arkady Gavrilov
Department of Electrical Engineering, Technion–Israel Institute of Technology, Haifa, 32000, Israel
8 shared publicationsDan Ritter
Department of Electrical Engineering, Technion–Israel Institute of Technology, Haifa, 32000, Israel
8 shared publicationsMoshe Eizenberg
Department of Materials Science and Engineering, Technion–Israel Institute of Technology, Haifa, 32000, Israel
8 shared publications- Steven DenBaars
University of California
8 shared publications Daniel A. Cohen
Materials Department, University of California, Santa Barbara, California 93106, USA
6 shared publicationsShuji Nakamura
Materials Department, University of California, Santa Barbara, California 93107, USA
6 shared publications
Latest Publications
- Open Access
- 25 July 2019
- Published by Optica Publishing Group in Optics Express
- Vol. 27 (16) , 22764-22769
Electrical injection of a 440nm InGaN laser with lateral confinement by nanoporous-GaN
We report observations of lateral mode confinement by a tapering nanoporous-GaN layer in the n-side cladding of a blue-emitting InGaN laser diode grown on the semipolar plane of bulk GaN. Little additional confinement occurred in the transverse direction, and the nanoporous layer did not serve as a current aperture. Nanoporous-GaN, with Si-doping of 8x1018 cm−3 and 20% porosity had a bulk resistivity of 3 Ω-cm and a thermal conductivity of 4 W/m-K, in general agreement with data reported on c-plane VCSEL structures. An excess modal loss of 19 cm−1 was found.- 25 July 2019
- Published by Optica Publishing Group in Optics Express
- Vol. 27 (16) , 22764-22769
Open AccessElectrical injection of a 440nm InGaN laser with lateral confinement by nanoporous-GaN
We report observations of lateral mode confinement by a tapering nanoporous-GaN layer in the n-side cladding of a blue-emitting InGaN laser diode grown on the semipolar plane of bulk GaN. Little additional confinement occurred in the transverse direction, and the nanoporous layer did not serve as a current aperture. Nanoporous-GaN, with Si-doping of 8x1018 cm−3 and 20% porosity had a bulk resistivity of 3 Ω-cm and a thermal conductivity of 4 W/m-K, in general agreement with data reported on c-plane VCSEL structures. An excess modal loss of 19 cm−1 was found. - 11 June 2019
- Published by Optica Publishing Group in Optics Letters
- Vol. 44 (12) , 3106-3109
Continuous-wave operation of a semipolar InGaN distributed-feedback blue laser diode with a first-order indium tin oxide surface grating
A novel approach to realize DFB gratings on GaN based laser diodes is presented and continuous-wave single longitudinal mode operation is achieved. The first order gratings were fabricated on the surface of indium tin oxide (ITO) on top of the laser ridge, which combines the benefits of simplified fabrication, easy scalability to wider ridges, and no regrowth or overgrowth. Under continuous-wave operation, the laser emits with a full FWHM of 5 pm, a SMSR of 29 dB and output power from a single facet as high as 80 mW. To the best of authors’ knowledge, this is also the first demonstration of a DFB-LD on semipolar InGaN/GaN system.
- 11 June 2019
- Published by Optica Publishing Group in Optics Letters
- Vol. 44 (12) , 3106-3109
Continuous-wave operation of a semipolar InGaN distributed-feedback blue laser diode with a first-order indium tin oxide surface grating
A novel approach to realize DFB gratings on GaN based laser diodes is presented and continuous-wave single longitudinal mode operation is achieved. The first order gratings were fabricated on the surface of indium tin oxide (ITO) on top of the laser ridge, which combines the benefits of simplified fabrication, easy scalability to wider ridges, and no regrowth or overgrowth. Under continuous-wave operation, the laser emits with a full FWHM of 5 pm, a SMSR of 29 dB and output power from a single facet as high as 80 mW. To the best of authors’ knowledge, this is also the first demonstration of a DFB-LD on semipolar InGaN/GaN system.
- Open Access
- 1 March 2019
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10939, 15
Semipolar III-nitride laser diodes for solid-state lighting
Several hurdles to further enhance the performance of semipolar III-Nitride laser diodes are addressed in this work. Particularly, we focused on improving their high operating voltage by thinning the p-GaN cladding layer and utilizing a transparent conductive oxide p-contact. On-wafer optical absorption measurements showed that a further reduction in voltage with thinner p-GaN was limited by increased optical loss due to increased mode overlap with the ITO/metal anode. In separate attempts to minimize bulk-related optical losses, we implemented a new design that consisted of an AlGaN electron blocking layer (EBL) placed remotely from the quantum wells (QWs) and a low p-waveguide Mg doping profile. A very low optical loss of about 2 cm-1 was extracted but the net improvement in differential efficiency was limited by lower internal injection efficiency due to carrier accumulation in the p-waveguide region. With an optimized design, that consisted of a lightly doped EBL close to the QWs and a UID p-waveguide, an improved light output power of 1.4 W at 1.5 A and a low threshold current density of 1.2 kA/cm2 were obtained.
- 1 March 2019
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10939, 15
Open AccessSemipolar III-nitride laser diodes for solid-state lighting
Several hurdles to further enhance the performance of semipolar III-Nitride laser diodes are addressed in this work. Particularly, we focused on improving their high operating voltage by thinning the p-GaN cladding layer and utilizing a transparent conductive oxide p-contact. On-wafer optical absorption measurements showed that a further reduction in voltage with thinner p-GaN was limited by increased optical loss due to increased mode overlap with the ITO/metal anode. In separate attempts to minimize bulk-related optical losses, we implemented a new design that consisted of an AlGaN electron blocking layer (EBL) placed remotely from the quantum wells (QWs) and a low p-waveguide Mg doping profile. A very low optical loss of about 2 cm-1 was extracted but the net improvement in differential efficiency was limited by lower internal injection efficiency due to carrier accumulation in the p-waveguide region. With an optimized design, that consisted of a lightly doped EBL close to the QWs and a UID p-waveguide, an improved light output power of 1.4 W at 1.5 A and a low threshold current density of 1.2 kA/cm2 were obtained.
- 1 February 2019
- Published by Elsevier in Journal of Crystal Growth
- Vol. 507, 118-123
Compensation effects of high oxygen levels in semipolar AlGaN electron blocking layers and their mitigation via growth optimization
- 1 February 2019
- Published by Elsevier in Journal of Crystal Growth
- Vol. 507, 118-123
Compensation effects of high oxygen levels in semipolar AlGaN electron blocking layers and their mitigation via growth optimization
- 8 January 2019
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 58 (2) , 020902
Semipolar InGaN blue laser diodes with a low optical loss and a high material gain obtained by suppression of carrier accumulation in the p-waveguide region
We obtained InGaN laser diodes (LDs) with a low optical loss (1.9 ± 0.6 cm −1 ) by utilizing an undoped In 0.07 Ga 0.93 N p-waveguide (p-WG) and a remote p-AlGaN electron blocking layer. This improvement, however, was accompanied by a low injection efficiency (37%) and a poor material gain. Electroluminescence measurements and energy band diagram simulations revealed excessive carrier accumulation in the p-WG region, which was suppressed by introducing an undoped indium-free GaN p-WG. This enabled LDs with a high material gain, a low optical loss (4.6 ± 0.7 cm −1 ), an improved injection efficiency (60%), and a peak light output power of 1.6 W at 1.5 A.
- 8 January 2019
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 58 (2) , 020902
Semipolar InGaN blue laser diodes with a low optical loss and a high material gain obtained by suppression of carrier accumulation in the p-waveguide region
We obtained InGaN laser diodes (LDs) with a low optical loss (1.9 ± 0.6 cm −1 ) by utilizing an undoped In 0.07 Ga 0.93 N p-waveguide (p-WG) and a remote p-AlGaN electron blocking layer. This improvement, however, was accompanied by a low injection efficiency (37%) and a poor material gain. Electroluminescence measurements and energy band diagram simulations revealed excessive carrier accumulation in the p-WG region, which was suppressed by introducing an undoped indium-free GaN p-WG. This enabled LDs with a high material gain, a low optical loss (4.6 ± 0.7 cm −1 ), an improved injection efficiency (60%), and a peak light output power of 1.6 W at 1.5 A.
- 1 January 2019
- Published by Optica Publishing Group
- p. PT2C.1
GaN High-Power Lasers for solid-state lighting
We discuss the use of GaN high-power laser diode in general lighting applications. After reviewing the laser diode achievements; the phosphors materials, the optical design and the possible performances of these devices are discussed.
- 1 January 2019
- Published by Optica Publishing Group
- p. PT2C.1
GaN High-Power Lasers for solid-state lighting
We discuss the use of GaN high-power laser diode in general lighting applications. After reviewing the laser diode achievements; the phosphors materials, the optical design and the possible performances of these devices are discussed.
- 1 June 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
Optical Gain and Loss Measurements of Semipolar III-nitride Laser Diodes with ITO/thin-p-GaN Cladding Layers
Laser diodes (LDs) based on the group III-nitride material system are forecasted to be the key components of next generation high-intensity white lighting systems [1]. For such systems, LDs offer more power per chip area, much higher spatial brightness, and no efficiency droop above threshold compared to light emitting diodes (LEDs). To meet these expectations, high-power and high-efficiency continuous-wave (CW) operation of a LD is essential. However, to date, InGaN LDs performance is still hampered by a high operating voltage and a poor differential efficiency, which result in lower wall-plug efficiencies (WPE) than InGaN LEDs or other III-V LDs [2], [3]. We have recently demonstrated an enhanced CW performance of blue LDs grown on a semipolar (202̅1̅) n-GaN substrate by replacing part of the resistive p-GaN cladding layer with a tin-doped indium oxide (ITO) layer [4]. With this transparent conductive oxide (TCO) layer, which has a lower modal optical loss than standard metallic p-contacts, and thinned p-GaN layer a very low operating voltage was obtained. Here, we present detailed gain and absorption measurements of these devices. We show a very low optical loss by redesigning the AlGaN electron blocking layer and the p-waveguide doping profile.
- 1 June 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
Optical Gain and Loss Measurements of Semipolar III-nitride Laser Diodes with ITO/thin-p-GaN Cladding Layers
Laser diodes (LDs) based on the group III-nitride material system are forecasted to be the key components of next generation high-intensity white lighting systems [1]. For such systems, LDs offer more power per chip area, much higher spatial brightness, and no efficiency droop above threshold compared to light emitting diodes (LEDs). To meet these expectations, high-power and high-efficiency continuous-wave (CW) operation of a LD is essential. However, to date, InGaN LDs performance is still hampered by a high operating voltage and a poor differential efficiency, which result in lower wall-plug efficiencies (WPE) than InGaN LEDs or other III-V LDs [2], [3]. We have recently demonstrated an enhanced CW performance of blue LDs grown on a semipolar (202̅1̅) n-GaN substrate by replacing part of the resistive p-GaN cladding layer with a tin-doped indium oxide (ITO) layer [4]. With this transparent conductive oxide (TCO) layer, which has a lower modal optical loss than standard metallic p-contacts, and thinned p-GaN layer a very low operating voltage was obtained. Here, we present detailed gain and absorption measurements of these devices. We show a very low optical loss by redesigning the AlGaN electron blocking layer and the p-waveguide doping profile.
- 16 January 2018
- Published by Optica Publishing Group in Optics Express
- Vol. 26 (2) , 1564-1572
Demonstration of enhanced continuous-wave operation of blue laser diodes on a semipolar 202¯1¯ GaN substrate using indium-tin-oxide/thin-p-GaN cladding layers
The benefits of utilizing transparent conductive oxide on top of a thin p-GaN layer for continuous-wave (CW) operation of blue laser diodes (LDs) were investigated. A very low operating voltage of 5.35 V at 10 kA/cm2 was obtained for LDs with 250 nm thick p-GaN compared to 7.3 V for LDs with conventional 650 nm thick p-GaN. An improved thermal performance was also observed for the thin p-GaN samples resulting in a 40% increase in peak light output power and a 32% decrease in surface temperature. Finally, a tradeoff was demonstrated between low operating voltage and increased optical modal loss in the indium tin oxide (ITO) with thinner p-GaN. LDs lasing at 445 nm with 150 nm thick p-GaN had an excess modal loss while LDs with an optimal 250 nm thick p-GaN resulted in optical output power of 1.1 W per facet without facet coatings and a wall-plug efficiency of 15%.
- 16 January 2018
- Published by Optica Publishing Group in Optics Express
- Vol. 26 (2) , 1564-1572
Demonstration of enhanced continuous-wave operation of blue laser diodes on a semipolar 202¯1¯ GaN substrate using indium-tin-oxide/thin-p-GaN cladding layers
The benefits of utilizing transparent conductive oxide on top of a thin p-GaN layer for continuous-wave (CW) operation of blue laser diodes (LDs) were investigated. A very low operating voltage of 5.35 V at 10 kA/cm2 was obtained for LDs with 250 nm thick p-GaN compared to 7.3 V for LDs with conventional 650 nm thick p-GaN. An improved thermal performance was also observed for the thin p-GaN samples resulting in a 40% increase in peak light output power and a 32% decrease in surface temperature. Finally, a tradeoff was demonstrated between low operating voltage and increased optical modal loss in the indium tin oxide (ITO) with thinner p-GaN. LDs lasing at 445 nm with 150 nm thick p-GaN had an excess modal loss while LDs with an optimal 250 nm thick p-GaN resulted in optical output power of 1.1 W per facet without facet coatings and a wall-plug efficiency of 15%.
- 23 August 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 38 (10) , 1504
Corrections to “Density of Traps at the Insulator/III-N Interface of GaN Heterostructure Field-Effect Transistors Obtained by Gated Hall Measurements” [Sep 15 893-895]
In the above paper, equation 5 should read (1)$dV_{B} ={d\left ({ {q\Delta n} }\right )} / {C_{B} }$ Equation 6 should read(2)$D_{it} \left ({ {E_{f} +{q\Delta n}/ {C_{B} }} }\right )\approx \frac {C_{B} C_{I} }{q^{2}}\left [{ {\left ({ {\frac {d\left ({ {q\Delta n} }\right )}{dV_{G} }} }\right )^{-1}-\frac {1}{C_{HF} }} }\right ]$ - 23 August 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 38 (10) , 1504
Corrections to “Density of Traps at the Insulator/III-N Interface of GaN Heterostructure Field-Effect Transistors Obtained by Gated Hall Measurements” [Sep 15 893-895]
In the above paper, equation 5 should read (1)$dV_{B} ={d\left ({ {q\Delta n} }\right )} / {C_{B} }$ Equation 6 should read(2)$D_{it} \left ({ {E_{f} +{q\Delta n}/ {C_{B} }} }\right )\approx \frac {C_{B} C_{I} }{q^{2}}\left [{ {\left ({ {\frac {d\left ({ {q\Delta n} }\right )}{dV_{G} }} }\right )^{-1}-\frac {1}{C_{HF} }} }\right ]$ - 3 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 63 (12) , 4702-4706
The Role of Barrier Transport and Traps in the Tradeoff Between Low OFF-State Leakage Current and Improved Dynamic Stability of AlGaN/GaN HFETs
A tradeoff behavior between low Schottky gate leakage current and improved dynamic stability of AlGaN/GaN heterostructure FETs was previously reported, and was attributed to variations in the metal/semiconductor interface properties. Here, we show that a tradeoff behavior is found in transistors and gated van der Pauw test structures that were fabricated on the same wafer, and underwent identical surface treatments. In the gated van der Pauw measurements, a slow transient response and a large variation in the 2-D electron gas concentration compared with equilibrium were detected, following a gate voltage stress in low leakage devices, but not in high leakage ones. Based upon our experimental observations, we argue that electron traps located in the AlGaN barrier layer are responsible for the tradeoff. The activation energies required to fill the empty barrier traps by electrons, obtained from the gated van der Pauw measurements, are 0.60 and 0.65 eV.
- 3 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 63 (12) , 4702-4706
The Role of Barrier Transport and Traps in the Tradeoff Between Low OFF-State Leakage Current and Improved Dynamic Stability of AlGaN/GaN HFETs
A tradeoff behavior between low Schottky gate leakage current and improved dynamic stability of AlGaN/GaN heterostructure FETs was previously reported, and was attributed to variations in the metal/semiconductor interface properties. Here, we show that a tradeoff behavior is found in transistors and gated van der Pauw test structures that were fabricated on the same wafer, and underwent identical surface treatments. In the gated van der Pauw measurements, a slow transient response and a large variation in the 2-D electron gas concentration compared with equilibrium were detected, following a gate voltage stress in low leakage devices, but not in high leakage ones. Based upon our experimental observations, we argue that electron traps located in the AlGaN barrier layer are responsible for the tradeoff. The activation energies required to fill the empty barrier traps by electrons, obtained from the gated van der Pauw measurements, are 0.60 and 0.65 eV.