Thomas Aichinger
Thomas Aichinger has a total of 45 co-authors. Here are the top co-authors by number of shared publications:
- Tibor Grasser
Technische Universität Wien
8 shared publications - Gregor Pobegen
KAI GmbH
6 shared publications - Hans Reisinger
Infineon Technologies AG, Neubiberg, Germany
5 shared publications - Maximilian Wolfgang Feil
Infineon Technologies AG, Neubiberg, Germany
4 shared publications Aleksandr Vasilev
Christian Doppler Laboratory for Single Defect Spectroscopy, Institute for Microelectronics, TU Wien, Vienna, Austria
2 shared publications- Dominic Waldhoer
Technische Universität Wien
2 shared publications
Latest Publications
- 24 November 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 127 (21)
Photoexcitation-assisted EDMR on SiC JFETs for quantum sensing applications
Electrically detected magnetic resonance (EDMR) is a powerful tool to interrogate quantum phenomena in semiconductors, e.g., to facilitate microelectronic sensors such as magnetometers. However, efforts to increase EDMR magnetometer sensitivity into the critical single-digit nT/Hz range have stalled, prompting recent electro-optical pumping schemes. Notable advancements in enhancing the EDMR response in silicon carbide (SiC) devices exposed to ultraviolet (UV) light have been reported. We investigate the interplay between UV excitation and bias voltage in UV-pumped EDMR using a 4H-SiC junction field-effect transistor (JFET). We identify two sensitivity-improving operational regimes: (i) spin-dependent recombination (SDR)-dominated signal enhancement in the standard forward-bias range, and (ii) noise reduction enabled by UV-induced shifting of the device open-circuit voltage UOC. While our sensor clearly benefits from signal enhancement, we also observe a saturation of this effect at higher biases and excitation powers. By contrast, operation in the UOC regime emerges as a promising alternative, where we report a record EDMR contrast, exceeding 2%. We achieve a maximum sensitivity of 30 nT/Hz, on par with record performances reported for EDMR magnetometers. This is projected to reach a single-digit nT/Hz figures of merit at higher photoexcitation power. Our findings highlight the potential of UV-enhanced EDMR, despite saturation limits in the forward-bias regime, and establish photoexcited EDMR magnetometers as a competitive alternative to state-of-the-art magnetic field sensors.
- 24 November 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 127 (21)
Photoexcitation-assisted EDMR on SiC JFETs for quantum sensing applications
Electrically detected magnetic resonance (EDMR) is a powerful tool to interrogate quantum phenomena in semiconductors, e.g., to facilitate microelectronic sensors such as magnetometers. However, efforts to increase EDMR magnetometer sensitivity into the critical single-digit nT/Hz range have stalled, prompting recent electro-optical pumping schemes. Notable advancements in enhancing the EDMR response in silicon carbide (SiC) devices exposed to ultraviolet (UV) light have been reported. We investigate the interplay between UV excitation and bias voltage in UV-pumped EDMR using a 4H-SiC junction field-effect transistor (JFET). We identify two sensitivity-improving operational regimes: (i) spin-dependent recombination (SDR)-dominated signal enhancement in the standard forward-bias range, and (ii) noise reduction enabled by UV-induced shifting of the device open-circuit voltage UOC. While our sensor clearly benefits from signal enhancement, we also observe a saturation of this effect at higher biases and excitation powers. By contrast, operation in the UOC regime emerges as a promising alternative, where we report a record EDMR contrast, exceeding 2%. We achieve a maximum sensitivity of 30 nT/Hz, on par with record performances reported for EDMR magnetometers. This is projected to reach a single-digit nT/Hz figures of merit at higher photoexcitation power. Our findings highlight the potential of UV-enhanced EDMR, despite saturation limits in the forward-bias regime, and establish photoexcited EDMR magnetometers as a competitive alternative to state-of-the-art magnetic field sensors.
- Open Access
- 12 September 2025
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 1024, 3-7
Dynamic Switching Energy Monitoring during Gate Switching Stress to Evaluate Performance Degradation in Hard Switching Electric Power Conversion Systems
In addition to the well-known bias temperature instability (BTI) phenomena, recently, it has been revealed that SiC MOSFETs show another instability during high-frequency repetitive switching between VGS(L) and VGS(H), referred to as gate-switching instability (GSI). This study shows the increase in switching energy caused by gate-switching instability VGS(th) drift as key performance parameters in electric power conversion systems, especially, when operating in hard-switching mode. A new methodology based on double pulse test was applied at each readout. The results highlighted the significance of the degradation mechanism through its impact on hard-switching applications with high-switching frequency. Therefore ruggedness against GSI plays a pivotal role in the long-term reliable operation of SiC MOSFET devices to ensure durable and efficient power conversion systems.
- 12 September 2025
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 1024, 3-7
Open AccessDynamic Switching Energy Monitoring during Gate Switching Stress to Evaluate Performance Degradation in Hard Switching Electric Power Conversion Systems
In addition to the well-known bias temperature instability (BTI) phenomena, recently, it has been revealed that SiC MOSFETs show another instability during high-frequency repetitive switching between VGS(L) and VGS(H), referred to as gate-switching instability (GSI). This study shows the increase in switching energy caused by gate-switching instability VGS(th) drift as key performance parameters in electric power conversion systems, especially, when operating in hard-switching mode. A new methodology based on double pulse test was applied at each readout. The results highlighted the significance of the degradation mechanism through its impact on hard-switching applications with high-switching frequency. Therefore ruggedness against GSI plays a pivotal role in the long-term reliable operation of SiC MOSFET devices to ensure durable and efficient power conversion systems.
- Open Access
- 23 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (7) , 4218-4226
Gate Switching Instability in Silicon Carbide MOSFETs—Part II: Modeling
It has recently been observed that bipolar switching between accumulation and inversion can result in an unexpected threshold voltage drift in SiC MOSFETs. This phenomenon has been termed gate switching instability (GSI) and is characterized by power-law time exponents close to unity, significantly larger than what is typically observed for ordinary bias temperature instability (BTI) during static or unipolar switching stress. Since the bias, frequency, and temperature dependence of GSI are the same as what is seen in charge pumping (CP) experiments, we stipulate that recombination events at the interface lead to recombination-enhanced defect reactions (REDRs), which can eventually lead to degradation. Based on these observations, we develop a comprehensive physical model for GSI, discuss its features, derive a closed form analytical solution, and finally validate the model against detailed experimental data.
- 23 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (7) , 4218-4226
Open AccessGate Switching Instability in Silicon Carbide MOSFETs—Part II: Modeling
It has recently been observed that bipolar switching between accumulation and inversion can result in an unexpected threshold voltage drift in SiC MOSFETs. This phenomenon has been termed gate switching instability (GSI) and is characterized by power-law time exponents close to unity, significantly larger than what is typically observed for ordinary bias temperature instability (BTI) during static or unipolar switching stress. Since the bias, frequency, and temperature dependence of GSI are the same as what is seen in charge pumping (CP) experiments, we stipulate that recombination events at the interface lead to recombination-enhanced defect reactions (REDRs), which can eventually lead to degradation. Based on these observations, we develop a comprehensive physical model for GSI, discuss its features, derive a closed form analytical solution, and finally validate the model against detailed experimental data.
- Open Access
- 16 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (7) , 4210-4217
Gate Switching Instability in Silicon Carbide MOSFETs—Part I: Experimental
In the context of renewable energy generation, compact and efficient electric power conversion is becoming increasingly important. Due to their low-loss switching capability at high frequencies, of up to hundreds of kilohertz, silicon carbide (SiC) MOSFETs are currently gaining a lot of attention from industry and are gradually replacing silicon (Si)-based devices in numerous applications. Recently, it has been revealed that SiC MOSFETs show a new type of instability in extensive high-frequency operations when the device is switched in bipolar mode. This gate switching instability has been observed in all commercial devices and occurs concurrently with the well-known bias temperature instability. We summarize the defining experimental characteristics of gate switching instability, including frequency, voltage, temperature, transition time dependencies, and the impact of undershoots in gate voltage. Subsequently, we discuss these observations together with those from other researchers, including recently proposed mechanisms and how they agree or disagree with the available experimental evidence. In the second part of this publication, we will present a detailed physics-based model that fully agrees with all presented experiments.
- 16 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (7) , 4210-4217
Open AccessGate Switching Instability in Silicon Carbide MOSFETs—Part I: Experimental
In the context of renewable energy generation, compact and efficient electric power conversion is becoming increasingly important. Due to their low-loss switching capability at high frequencies, of up to hundreds of kilohertz, silicon carbide (SiC) MOSFETs are currently gaining a lot of attention from industry and are gradually replacing silicon (Si)-based devices in numerous applications. Recently, it has been revealed that SiC MOSFETs show a new type of instability in extensive high-frequency operations when the device is switched in bipolar mode. This gate switching instability has been observed in all commercial devices and occurs concurrently with the well-known bias temperature instability. We summarize the defining experimental characteristics of gate switching instability, including frequency, voltage, temperature, transition time dependencies, and the impact of undershoots in gate voltage. Subsequently, we discuss these observations together with those from other researchers, including recently proposed mechanisms and how they agree or disagree with the available experimental evidence. In the second part of this publication, we will present a detailed physics-based model that fully agrees with all presented experiments.
- Open Access
The Impact of Interfacial Charge Trapping on the Reproducibility of Measurements of Silicon Carbide MOSFET Device Parameters
Silicon carbide is an emerging material in the field of wide band gap semiconductor devices. Due to its high critical breakdown field and high thermal conductance, silicon carbide MOSFET devices are predestined for high-power applications. The concentration of defects with short capture and emission time constants is higher than in silicon technologies by orders of magnitude which introduces threshold voltage dynamics in the volt regime even on very short time scales. Measurements are heavily affected by timing of readouts and the applied gate voltage before and during the measurement. As a consequence, device parameter determination is not as reproducible as in the case of silicon technologies. Consequent challenges for engineers and researchers to measure device parameters have to be evaluated. In this study, we show how the threshold voltage of planar and trench silicon carbide MOSFET devices of several manufacturers react on short gate pulses of different lengths and voltages and how they influence the outcome of application-relevant pulsed current-voltage characteristics. Measurements are performed via a feedback loop allowing in-situ tracking of the threshold voltage with a measurement delay time of only 1 . Device preconditioning, recently suggested to enable reproducible BTI measurements, is investigated in the context of device parameter determination by varying the voltage and the length of the preconditioning pulse.Open AccessThe Impact of Interfacial Charge Trapping on the Reproducibility of Measurements of Silicon Carbide MOSFET Device Parameters
Silicon carbide is an emerging material in the field of wide band gap semiconductor devices. Due to its high critical breakdown field and high thermal conductance, silicon carbide MOSFET devices are predestined for high-power applications. The concentration of defects with short capture and emission time constants is higher than in silicon technologies by orders of magnitude which introduces threshold voltage dynamics in the volt regime even on very short time scales. Measurements are heavily affected by timing of readouts and the applied gate voltage before and during the measurement. As a consequence, device parameter determination is not as reproducible as in the case of silicon technologies. Consequent challenges for engineers and researchers to measure device parameters have to be evaluated. In this study, we show how the threshold voltage of planar and trench silicon carbide MOSFET devices of several manufacturers react on short gate pulses of different lengths and voltages and how they influence the outcome of application-relevant pulsed current-voltage characteristics. Measurements are performed via a feedback loop allowing in-situ tracking of the threshold voltage with a measurement delay time of only 1 . Device preconditioning, recently suggested to enable reproducible BTI measurements, is investigated in the context of device parameter determination by varying the voltage and the length of the preconditioning pulse. - 1 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Influence of high-voltage gate-oxide pulses on the BTI behavior of SiC MOSFETs
We study the bias temperature instability (BTI) behavior of 4H-SiC trench MOSFETs after application of very high gate-voltage pulses at high temperatures. These pulses correspond to an electric field sufficiently high to trigger impact ionization and the associated effects in gate oxides. BTI effects measured in the form of threshold voltage or V Th drifts are more severe after these pulses as compared to BTI after voltage pulses that are sufficiently below the impact ionization regime. The effects shown in this paper impose an upper limit on electric fields applied to the gate during, e.g., device screening during front-end processing, but also in the application.
- 1 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Influence of high-voltage gate-oxide pulses on the BTI behavior of SiC MOSFETs
We study the bias temperature instability (BTI) behavior of 4H-SiC trench MOSFETs after application of very high gate-voltage pulses at high temperatures. These pulses correspond to an electric field sufficiently high to trigger impact ionization and the associated effects in gate oxides. BTI effects measured in the form of threshold voltage or V Th drifts are more severe after these pulses as compared to BTI after voltage pulses that are sufficiently below the impact ionization regime. The effects shown in this paper impose an upper limit on electric fields applied to the gate during, e.g., device screening during front-end processing, but also in the application.
- Top Cited Papers
- 3 October 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 66 (11) , 4604-4616
Review on SiC MOSFETs High-Voltage Device Reliability Focusing on Threshold Voltage Instability
An overview over issues and findings in SiC power MOSFET reliability is given. The focus of this article is on threshold instabilities and the differences to Si power MOSFETs. Measurement techniques for the characterization of the threshold voltage instabilities are compared and discussed. Modeling of the threshold voltage instabilities based on capture-emission-time (CET) maps is a central topic. This modeling approach takes the complete gate bias/temperature history into account. It includes both gate stress polarities and is able to reproduce the short-term threshold variations during application-relevant 50-kHz bipolar ac-stress. In addition, the impact on circuit operation is discussed.
- 3 October 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 66 (11) , 4604-4616
Top Cited PapersReview on SiC MOSFETs High-Voltage Device Reliability Focusing on Threshold Voltage Instability
An overview over issues and findings in SiC power MOSFET reliability is given. The focus of this article is on threshold instabilities and the differences to Si power MOSFETs. Measurement techniques for the characterization of the threshold voltage instabilities are compared and discussed. Modeling of the threshold voltage instabilities based on capture-emission-time (CET) maps is a central topic. This modeling approach takes the complete gate bias/temperature history into account. It includes both gate stress polarities and is able to reproduce the short-term threshold variations during application-relevant 50-kHz bipolar ac-stress. In addition, the impact on circuit operation is discussed.
- 1 October 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 66 (11) , 4692-4697
NH3and NO + NH3Annealing of 4H-SiC Trench MOSFETs: Device Performance and Reliability
As the gate oxide (GOX)-SiC interface of SiC MOSFETs is crucial for device performance, it requires special attention. To improve interface quality, device performance, and reliability, commonly, a postoxidation anneal (POA) is applied. Different gas compositions can be used to passivate the SiC interface and bulk oxide. We study the effects of ammonia (NH₃) and a new combined NO + NH₃ POA on 4H-SiC trench MOSFET test structures and compare them to the common nitric oxide (NO) POA. Our studies are not only limited to device performance represented by channel mobility but also contain reliability studies in the form of bias temperature instability (BTI), sweep hysteresis, Fowler-Nordheim (FN) tunneling and GOX breakdown. We find that both, NH₃ and NO + NH₃ result in higher mobility than NO annealed test structures. On the other hand, ammonia containing POAs deteriorate device reliability, e.g., leading to larger BTI and higher tunneling currents. As both can be detrimental in certain applications, they must be optimized. We show that NO + NH₃ anneals may offer an acceptable compromise between the characteristics of NO and NH₃ with regard to tunneling and device performance. However, it shows more positive BTI (PBTI) drift than NH₃ and NO. We will show that a full characterization of the GOX is essential to evaluate, optimize, and benchmark new annealing strategies.
- 1 October 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 66 (11) , 4692-4697
NH3and NO + NH3Annealing of 4H-SiC Trench MOSFETs: Device Performance and Reliability
As the gate oxide (GOX)-SiC interface of SiC MOSFETs is crucial for device performance, it requires special attention. To improve interface quality, device performance, and reliability, commonly, a postoxidation anneal (POA) is applied. Different gas compositions can be used to passivate the SiC interface and bulk oxide. We study the effects of ammonia (NH₃) and a new combined NO + NH₃ POA on 4H-SiC trench MOSFET test structures and compare them to the common nitric oxide (NO) POA. Our studies are not only limited to device performance represented by channel mobility but also contain reliability studies in the form of bias temperature instability (BTI), sweep hysteresis, Fowler-Nordheim (FN) tunneling and GOX breakdown. We find that both, NH₃ and NO + NH₃ result in higher mobility than NO annealed test structures. On the other hand, ammonia containing POAs deteriorate device reliability, e.g., leading to larger BTI and higher tunneling currents. As both can be detrimental in certain applications, they must be optimized. We show that NO + NH₃ anneals may offer an acceptable compromise between the characteristics of NO and NH₃ with regard to tunneling and device performance. However, it shows more positive BTI (PBTI) drift than NH₃ and NO. We will show that a full characterization of the GOX is essential to evaluate, optimize, and benchmark new annealing strategies.
- 19 July 2019
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 963, 194-198
First Principles Study of the Influence of the Local Steric Environment on the Incorporation and Migration of NO in a-SiO2
The NO anneal has been shown to effectively remove 99% of defects in SiC based devices. However, the details of interactions of NO molecules with amorphous (a)-SiO2 and SiC/SiO2 interface are still poorly understood. We use DFT simulations to investigate the NO incorporation energies in a-SiO2, and how these are affected by the steric environment. The results explain the ease with which NO molecules incorporate into a-SiO2 and give an insight into the diffusion paths they take during annealing. We highlight the importance of exhaustive sampling for exploring NO diffusion pathways.
- 19 July 2019
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 963, 194-198
First Principles Study of the Influence of the Local Steric Environment on the Incorporation and Migration of NO in a-SiO2
The NO anneal has been shown to effectively remove 99% of defects in SiC based devices. However, the details of interactions of NO molecules with amorphous (a)-SiO2 and SiC/SiO2 interface are still poorly understood. We use DFT simulations to investigate the NO incorporation energies in a-SiO2, and how these are affected by the steric environment. The results explain the ease with which NO molecules incorporate into a-SiO2 and give an insight into the diffusion paths they take during annealing. We highlight the importance of exhaustive sampling for exploring NO diffusion pathways.
- Open Access
- 3 April 2018
- Published by Wiley in Advanced Materials Interfaces
- Vol. 5 (12)
Impact of the NO Anneal on the Microscopic Structure and Chemical Composition of the Si‐Face 4H‐SiC/SiO2 Interface
Understanding the microscopic structure of the SiC/SiO2 interface is crucial for the improvement of SiC based metal‐oxide‐semiconductor field‐effect transistors (MOSFETs). It is well established that interface states degrade the performance and reliability of SiC MOSFETs and that passivation can be achieved by anneals in NO‐containing atmospheres. However, the structural changes associated with the NO anneal and the improvement of the channel electron mobility are still not fully understood. In this study, the SiC/SiO2 interface of the state‐of‐the art 4H‐SiC n‐channel MOSFETs with a deposited oxide is extensively investigated with advanced scanning transmission electron microscopy (STEM) and spatially resolved electron energy‐loss spectroscopy (EELS) methods. The samples are treated with different postoxidation anneals (NO vs O2), resulting in strongly differing mobility and point defect density. The most notable structural difference between the samples is an increased N concentration located in the transition region between the SiC and the SiO2 of the NO‐annealed sample. The N signal is evenly distributed along the whole faceted interface and has a half‐width of wN = (1.8 ± 0.7) nm and an estimated areal density of cN = (4 ± 1) × 1014 cm−2. The observations support the idea that the N incorporation happens predominantly directly at the SiC/SiO2 interface where defect states are passivated.
- 3 April 2018
- Published by Wiley in Advanced Materials Interfaces
- Vol. 5 (12)
Open AccessImpact of the NO Anneal on the Microscopic Structure and Chemical Composition of the Si‐Face 4H‐SiC/SiO2 Interface
Understanding the microscopic structure of the SiC/SiO2 interface is crucial for the improvement of SiC based metal‐oxide‐semiconductor field‐effect transistors (MOSFETs). It is well established that interface states degrade the performance and reliability of SiC MOSFETs and that passivation can be achieved by anneals in NO‐containing atmospheres. However, the structural changes associated with the NO anneal and the improvement of the channel electron mobility are still not fully understood. In this study, the SiC/SiO2 interface of the state‐of‐the art 4H‐SiC n‐channel MOSFETs with a deposited oxide is extensively investigated with advanced scanning transmission electron microscopy (STEM) and spatially resolved electron energy‐loss spectroscopy (EELS) methods. The samples are treated with different postoxidation anneals (NO vs O2), resulting in strongly differing mobility and point defect density. The most notable structural difference between the samples is an increased N concentration located in the transition region between the SiC and the SiO2 of the NO‐annealed sample. The N signal is evenly distributed along the whole faceted interface and has a half‐width of wN = (1.8 ± 0.7) nm and an estimated areal density of cN = (4 ± 1) × 1014 cm−2. The observations support the idea that the N incorporation happens predominantly directly at the SiC/SiO2 interface where defect states are passivated.