DBDeepak Bansal

Deepak Bansal

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Deepak Bansal has a total of 213 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Enhancing RF MEMS SPDT switch performance through fabrication and ground balance

    by Khushbu Singh Raghav, Dheeraj Kumar Kharbanda, Amit Kumar, Bhawani Shankar Jangir, Rama Kant Sharma, Shivam Tiwari, Ravindra Mukhiya, Deepak Bansal

    Radio frequency microelectromechanical system switches are gaining attention as an alternative to solid-state switches due to their low loss, high isolation, and excellent linearity. Although many single-pole single-throw designs are reported in the literature, multiport switches, especially single-pole double-throw (SPDT) switches, remain limited despite their key role in phase shifters, antenna switching, and transceiver systems. In Coplanar Waveguide-based SPDT switches, residual stress in the beam and grounding effects strongly influence pull-in voltage, beam deformation, insertion loss, and isolation. This work presents the complete development of an SPDT switch from design to measurement. Short- and long-path layouts are evaluated, with the short path showing better return loss. A solid cantilever initially requires a high pull-in voltage, which is reduced by introducing two windows near the anchor and tip, resulting in better damping and more stable contact. The fabrication process is also optimised to mitigate stress in the switch. After fabrication, a high insertion loss is observed due to the absence of a common ground. To overcome this, double wire-bond ground bridges are implemented to equalise the grounds, significantly improving insertion loss and yielding smooth isolation across the 100 MHz–20 GHz range.

  • Fabrication, Characterization, and Optimization of Robust Sensing Materials for MEMS LC Resonators in Harsh Aqueous Environments

    by Deepak Bansal, Khushbu Singh Raghav, Dheeraj Kumar Kharbanda, Amit Kumar, Deepak Panwar, Dhirendra Kumar, Somak Chatterjee, Mahesh Angira

    Sensing in harsh aqueous environments remains a critical challenge due to the limited lifetime and reliability of conventional electrode-based sensors. While laboratory-based techniques such as mass spectrometry, infrared spectroscopy, Raman spectroscopy, chromatography, filtration, multiple fermentation tube techniques, DNA amplification, capillary electrophoresis, field-flow fractionation, and fluorescence in situ hybridization (FISH) technique offer high accuracy for heavy metal ion detection, their complexity, cost, and lack of portability restrict their use for on-site monitoring. Resonant sensing, such as MEMS-based LC resonators, offers a promising alternative; however, their long-term performance is often constrained by chemical degradation of electrode materials when exposed to harsh aqueous media. Thus, in the presented work, a hard and chemically inert multilayer electrode stack (Ti/TiN/Al/Ti/TiN) is developed, with material selection optimized using the TOPSIS approach, and deposition is optimized within a single sputtering system. Titanium nitride is employed as the top protective layer due to its excellent chemical and mechanical stability under both acidic and alkaline conditions. The robustness of the proposed materials stack is experimentally validated across a wide pH range representative of industrial runoff, river water, and seawater, demonstrating negligible degradation in resonator performance. As a case study, lead nitrate is introduced to illustrate the sensor response, where changes in the dielectric and conductive properties of the aqueous medium result in measurable shifts in the resonator’s S21 parameter. Both simulated and measured results show good agreement, confirming the viability of the proposed platform. The presented materials stack and resonator architecture provide a robust sensing platform, which can be readily extended to resonant sensing of various analytes in harsh aqueous environments.

  • Buckling and Stress-Controlled RF MEMS Structures Using Annealing

    by Khushbu Singh Raghav, Amit Kumar, Prashant Sharma, Prateek Kothari, Mahesh Angira, Deepak Bansal

    Micro-Electro-Mechanical System (MEMS) devices show better performance as compared to solid-state devices in terms of radio frequency (RF) response, like insertion loss and isolation. However, MEMS devices face reliability issues, and stress is one of the main concerns. MEMS devices involve many non-traditional fabrication steps, like releasing hanging structures. Released MEMS structures show built-in stress from the fabrication process. This stress can cause them to bend, curl, or buckle. Especially in the case of Radio Frequency (RF) MEMS switches, curling buckling increases the pull-in voltage. In the literature, to address stress-related buckling, thermal annealing was applied at different temperatures after release. However, post-release annealing reduces the stress and results in curled-up and unstable structures. The present paper explores a novel and innovative method for thermally annealing structures at an appropriate stage to reduce stress and buckling in released cantilever structures. Annealing at the appropriate step results in a significant reduction in cantilever bending and warping, indicating effective stress relaxation and yielding straight, mechanically stable cantilevers. After controlling the stress and buckling, the pull-in voltage is reduced to 40 V, which is in close agreement with the simulated results. The measured insertion loss of the switch is -0.4 dB, and isolation is -22 dB for the DC to 20 GHz frequency range.


  • Open Access

    Fabrication of Air Cavity Structures Using DRIE for Acoustic Signal Confinement in FBAR Devices

    by Raju Patel, Manoj Singh Adhikari, Deepak Bansal, Tanmoy Majumder

    Acoustic energy penetrates into the Si substrate at cavity boundaries. Due to this, the air cavity-based bulk acoustic resonators experience higher harmonic mode, parasitic resonance, and spurious mode. To overcome these effects and enhance the performance parameters, a backside air cavity is fabricated using the deep reactive ion etching (DRIE) method. The DRIE method helps to achieve the optimized active area of the resonator. SiO2 film on a silicon substrate as the support layer and ZnO as the piezoelectric (PZE) film are used for the resonator. The crystal growth and surface morphology of ZnO film were investigated with X-ray diffraction, scanning electron microscopy, and atomic force microscopy. FBAR is modeled in a 1-D modified Butterworth–Van Dyke (mBVD) equivalent circuit. As RF measurement results, we successfully demonstrated a FBAR with optimized active area of 320 × 320 μm2, center frequency of 1.261 GHz, having a quality factor of 583.8. Overall, this suppression of higher harmonic mode shows the great potential for improving the selectivity of the sensor and also in RF filter design applications. This integration of DRIE-based cavity formation with ZnO-based FBAR architecture not only enables compact design but also effectively suppresses spurious and higher-order modes, which demonstrates a performance-enhancing fabrication strategy not fully explored in the current literature.


  • Design and Development of a Low Insertion Loss RF MEMS Shunt Ohmic Switch

    by Khushbu Singh Raghav, Maninder Kaur, Shivam Tiwari, Deepak Panwar, Amit Kumar, Deepak Bansal

    Recent advancements in the communication arena demand small-size devices with better transmission and minimum losses. Switches are the basic building blocks for any communication system. MEMS switches offer better performance in terms of size and losses than their mechanical and solid-state counterparts. Out of different MEMS switch types, ohmic switches are preferred over capacitive switches in terms of large bandwidth. Ohmic switches work over the entire frequency range starting from dc, whereas capacitive switches only operate in a particular frequency band. Hence, ohmic switches are preferred to cover multibands. However, the insertion loss of the usual series ohmic switches is higher than the capacitive switches due to contact resistance. In this article, a new concept for a shunt ohmic switch with low insertion loss has been designed and characterized. The contact resistance term is removed from the switch in the ON state. The insertion loss of the proposed shunt ohmic switch is less than $-$ 0.3 dB, and isolation is better than $-$ 17 dB over the frequency range of dc-6 GHz. The proposed switch is suitable for all the communication bands from 2G to 6G till sub-6-GHz technology.


  • Service Discovery Mechanism for Micro Services in Cloud Computing: Comparative Study

    by Deepak Bansal, Ruchika Bathla

    Cloud computing is an online service that is provided as services over the internet. Finding and using the services that are available, which is a crucial component for service-oriented applications, is one of the major challenges in cloud computing. This paper ranks service discovery mechanisms into three major classes: centralized, decentralized, and hybrid. In order to determine and contrast the usefulness and efficiency of various service discovery techniques for cloud computing's microservices, this comparative study looks at several service discovery strategies. It examines existing research papers and studies in order to compare different approaches used for cloud service discovery.A comparison of these methods shows that the decentralized technique depends on a distributed network while the centralized relies on the central registry and the hybrid is a combination of both approaches. This review paper helps researchers who would like to compare analyses of service discovery mechanisms in cloud computing.