SMStefan Mommer

Stefan Mommer

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Stefan Mommer has a total of 40 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Digital Printing of Photoreversible Protective Films

    by Morris Wolf, Alper Balkan, René Schneider, Stefan Mommer, Yves Leterrier, Mark W. Tibbitt

    Temporary protective coatings are widely used in modern production processes. Yet, while highly desirable, their high‐resolution printing and stimuli‐responsive removal remain challenging. To address this need, we introduce acrylate‐based photopolymerized and photoreversible protective films that can be applied using aerosol jet printing. The acrylate films were formulated using aqueous solutions of a photocleavable diacrylate cross‐linker and acrylated macromers. To form films, the precursor solution was cured with 405 nm light for 120 s. The films were subsequently removed via photodegradation upon exposure to 365 nm light within minutes to hours depending on film thickness and light intensity. The addition of a polyethyleneimine‐based adhesion promoter, Lupasol WF, led to significant improvement of adhesion to industry‐relevant surfaces. Quantification using a rheometer in extensional mode showed a fracture energy of the films 3.25x higher than without the adhesion promoter. The protective films were applied using aerosol jet printing, enabling a feature resolution below 30 µm and a spatially selective treatment of metallic surfaces with Paris oxide. These results demonstrate how photopolymerized and photoreversible polymer networks enable temporary protective coatings in industry‐relevant applications.

  • Open Access

    Self-Growing and Mechanically Tunable Living Materials with Paenibacillus mucilaginosus Extracellular Polymeric Substances

    by Yifan Cui, Stéphane Bernhard, Mathias Steinacher, Nika Petelinsek, Lorenzo Minervini, Stefan Mommer, Mark W. Tibbitt

    Engineered living materials (ELMs) typically embed functional cells in nonliving matrices, limiting growth, remodeling, and long-term adaptation at the material level. Here, we introduce extracellular polymeric substances (EPS) produced by Paenibacillus mucilaginosus as a living carrier matrix for ELMs. P. mucilaginosus EPS possesses suitable rheological behavior, such as shear thinning and elastic recovery, required for extrusion-based fabrication. Its mechanical properties can be further tuned through dynamic covalent cross-linking via boronate ester formation or physical reinforcement with Laponite or xanthan gum. With boronate ester cross-linking (18 mM), the storage modulus increased from 100 to 800 Pa. The inclusion of 0.5 w/v % Laponite further increased the modulus to 1300 Pa. Uniquely, a living matrix comprised ofP. mucilaginosus EPS provides a substrate for material growth. As a proof of concept, we manufactured photosynthetic living materials by embedding a photosynthetic cyanobacterium strain,Synechococcus sp. PCC 7002, in the EPS matrix and printed into defined architectures. Both P. mucilaginosus and cyanobacterium PCC 7002 remained viable and grew over 30 days. Matrix outgrowth and microbial colonization enabled the expansion of the living constructs within the printed structure. This work establishes P. mucilaginosus EPS as a candidate living scaffold for self-growing and mechanically tunable ELMs.


  • Open Access

    Tough Supramolecular CB[8] Hydrogels with Rapid Self-Recovery

    by Marius Schnider, Ivan Maroni, Stefan Mommer

    Tough hydrogels capable of dissipating large amounts of energy typically suffer from irreversible network damage due to excessive chain re-orientation and bond rupture. By exploiting cucurbituril (CB[8]) host—guest interactions as supramolecular crosslinks with fast relaxation dynamics, we bypass this classical tradeoff between toughness and self-recoverability. To this end, we introduce a new class of diallyl benzyl methyl ammonium chloride (DABMAC)-based guest monomers that are directly copolymerizable and simultaneously act as supramolecular cross-linkers through homoternary 1:2 complexation with CB[8]. Systematic variation of the para-substituent (R = iPr, H, CN, Me) on the benzyl group, characterized by 1H NMR spectroscopic titrations and isothermal titration calorimetry (ITC), reveals binding affinities (log = 6.32 to 12.14) and thermodynamic driving forces. Oscillatory rheology of the resulting poly(AAm-stat-DABMAC-R)–CB[8] hydrogels confirms that both network stiffness and relaxation dynamics scale directly with binding affinity and 1:2 stoichiometry. Combining these supramolecular cross-linkers with small amounts of a covalent cross-linker yields dual cross-linked hydrogels with fracture strains exceeding 6000%, toughness values up to 853 kJ/m3, and near-complete self-recovery within 8–10 seconds after stretching to 1000% strain. Cyclic tensile testing further demonstrates that a resting period as brief as 10 s restores hysteresis recovery to 99%, confirming that energy dissipation is kinetically controlled and fully reversible. These results position CB[8]based supramolecular hydrogels as a compelling materials platform for soft robotics, tissue engineering, and other load-bearing applications demanding both high toughness and self-recovery.

  • Open Access

    Iron-Binding Hydrogel Sensors for Multi-Well Plate Analysis

    by Lorenzo Minervini, Niklas Wittig, Stefan Mommer

    Sensory hydrogels for multi-well plate analysis represent an attractive method of analyte quantification, yet limited examples for metal detection exist to date. In this study we present an iron(III)-sensory hydrogel assay for multiwell plate analysis using deferasirox (DFS). We functionalized DFS to enable its polymerization into networks. The methacrylated DFS derivative (DFSMA) was structurally characterized by NMR spectroscopy. Its binding to iron(III) was retained in solution, when incorporated into a polymer and hydrogel, as assessed by NMR and UVVis spectroscopy. A hydrogel formulation was studied that allowed for a facile production of sensory hydrogels in 96-well plates. Various iron(III) levels were tested, calibration curves for absorbance and fluorescence were crafted, allowing for the quantification of unknown iron(III) levels. Additionally, the selectivity of this hydrogel assay was tested against a variety of (transition) metals, demonstrating its selective nature towards iron(III).

  • Open Access

    Enhanced toughness in highly entangled hydrogels via non-covalent molecular hooks

    by Élise Ansart, Lucien Cousin, Mark W. Tibbitt, Stefan Mommer

    Hydrogels with enhanced toughness have received increasing attention due to their potential for load-bearing applications. Recent findings have demonstrated that highly entangled networks are capable of forming such materials, yet their fabrication generally necessitates a covalent cross-linker, limiting their processability and applicability. In this work, we found that poly(ethylene glycol) methyl ether acrylate (PEGmeAc) can serve as a non-covalent cross-linker for highly entangled poly(acrylamide) networks in dilute state, imparting extreme stretchability (6600%) and toughness (26 MJ m−3) to the hydrogels that otherwise flow within minutes. Oscillatory and rotational rheology demonstrates that the incorporation of 1 mol% of PEGmeAc is sufficient to provide structural stability to the hydrogel, increase relaxation time and improve elastic response, and severely inhibits disentanglement under shear. We hypothesized that this effect was caused by a combination of hydrogen bonding and topological entanglements, making PEGmeAc act as “hooks” within the network. The mechanism was confirmed through a combination of dissolution assays and nuclear Overhauser enhancement spectroscopy (NOESY), which showed that hydrogen bonding and topological entanglements are at play. Consequently, the incorporation of small quantities of such monomers into hydrogels may open new pathways to enhance the mechanical properties of soft materials.


  • Open Access

    Fotoresponsive Slide‐Ring Gele ermöglichen Modulierung der Gleitdynamik

    by Dalila Cafagno, Serena Silvi, Mark W. Tibbitt, Stefan Mommer

    Abstrakt: Cyclodextrin‐basierte Slide‐Ring Gele (SRG) haben sich aufgrund ihrer einzigartigen Topologie zu einer vielversprechenden Materialklasse entwickelt. Bei mechanischer Belastung verlagern sich die gleitfähigen Vernetzungspunkte des Polymernetzwerks frei entlang des Polymerrückgrats. Dadurch können sie überaus effektiv Energie abbauen, was oft zu einer außergewöhnlichen Dehnbarkeit und Zähigkeit führt. Die Gleitdynamik spielt daher eine entscheidende Rolle für die mechanischen Eigenschaften von SRG. Unternehmungen, jene zu kontrollieren, beschränken sich jedoch in erster Linie auf die Gesamtzahl der Makrozyklen, die auf die Polymere aufgefädelt werden. Des Weiteren sind SRG, die durch einen externen Stimulus beeinflusst werden können, bisher nicht bekannt. In dieser Arbeit berichten wir über fotoresponsive SRG, die auf Azobenzol‐haltigen Polymeren basieren. Durch reversibles Schalten der Azobenzole wird die Gleitdynamik der gefädelten α‐Cyclodextrine (α‐CD) moduliert. Mithilfe von UV‐Vis Spektroskopie und Zirkulardichroismus zeigen wir, dass α‐CD an die Azobenzole entlang des Polymerrückgrats in der E ‐Konfiguration binden. Bei Lichteinstrahlung und damit Isomerisierung zum Z ‐Isomer interagieren die Makrozyklen nicht mehr mit den Azobenzolen, sodass sie sich frei entlang des Polymerrückgrats bewegen können. Infolge dieser E ‐zu‐ Z ‐Isomerisierung und der unterschiedlichen Gleitdynamik wechseln die mechanischen Eigenschaften der SRG reversibel zwischen einem steifen und einem weichen Zustand.


  • Open Access

    Photoresponsive Slide‐Ring Gels Enable Modulation of Sliding Dynamics

    by Dalila Cafagno, Serena Silvi, Mark W. Tibbitt, Stefan Mommer

    Cyclodextrin‐based slide‐ring gels (SRGs) have emerged as a promising class of materials owing to their unique topology. Upon mechanical loading, the slidable cross‐links of the polymer network freely translocate along the polymer backbone enabling pronounced energy dissipation in the material, which is associated with exceptional ductility and toughness. Despite the critical role of sliding dynamics in defining SRG mechanical properties, attempts to control them have primarily been limited to tuning the overall loading of macrocycles. Further, SRGs that can be triggered via an external stimulus have yet to be reported. In this work, we present light‐responsive SRGs based on azobenzene‐containing polymers. Reversible photoswitching of the azobenzenes modulates the sliding dynamics of the threaded α‐cyclodextrin (α‐CD) macrocycles. By using UV–Vis and circular dichroism spectroscopy, we show that α‐CDs readily bind to the azobenzenes along the polymer backbone in the E configuration. Upon light irradiation, and thus isomerization to the Z isomer, the macrocycles no longer interact with the azobenzenes, allowing them to freely translocate along the polymer backbone. As a result of this E to Z isomerization and difference in sliding dynamics, the mechanical properties of the SRGs reversibly alternate between a stiff and a soft state.


  • Open Access

    Ultrahigh-Molecular-Weight Polymer Gels in Aqueous Media Using Cucurbit[8]uril-Assisted Radical Polymerization

    by Élise Ansart, Rebekka Hosch, Mark W. Tibbitt, Stefan Mommer

    Ultrahigh-molecular-weight (UHMW) polymer materials show enhanced material properties due to entanglements and reduced polymer dynamics that occur at extreme degrees of polymerization. While various living controlled polymerizations have been explored for the synthesis of UHMW polymers, free-radical polymerization (FRP) remains limited for this application, given low initiation efficiencies and poor reproducibility. In this work, we exploit host-guest interactions between Cucurbit[8]-uril and the thermoinitiator VA-044 to down-regulate the number of active radicals during the radical polymerization of acrylamide (AAm). This approach produces UHMW polymers (up to 5.5 MDa) that form hydrogels in situ. We investigate various reaction parameters (e.g., the concentration of CB[8] and ratio of CB[8] to VA-044) and apply this strategy to other water-soluble monomers. Additionally, detailed rheological analyses of the materials show how upon exceeding a molecular weight of M n = 3 MDa, the stiffness of the hydrogels increases and becomes frequency-independent. Due to the simplicity of this method, UHMW polymers and hydrogels in aqueous media can be easily accessed by using minimal amounts of the CB[8] macrocycle as an additive to an otherwise standard FRP procedure.


  • Open Access

    Light and protonation-controlled complex formation between sulfate ions and a stiff-stilbene based bis(cyclopeptide)

    by Stefan Mommer, Benedict Wyrwol, Jasper E. Bos, Stefan Kubik, Sander J. Wezenberg

    Anion–ligand coordination has been used to generate a number of supramolecular structures. Of particular interest is the transformation between different types of complexes using various stimuli. While there are multiple examples where this has been achieved with metal–ligand coordination complexes through incorporation of molecular photoswitches, the same has not yet been realized with anion–ligand coordination-driven assemblies. In this study, a sulfate-binding bis(cyclopeptide) with a photoswitchable stiff-stilbene linker is presented. Its (E)- and (Z)-isomers, and the different degrees of protonation of the anion (HSO4 − vs. SO4 2−), give rise to different assembly states. The accessible products have 1 : 1, 1 : 2 and 2 : 2 host–guest stoichiometries and can be interconverted by light irradiation and acid/base addition, resulting in a highly controllable responsive system that demonstrates the potential of sulfate coordination-driven supramolecular assembly.


  • Top Cited Papers
    Open Access

    Tough Hydrogels for Load‐Bearing Applications

    by Nika Petelinšek, Stefan Mommer

    Tough hydrogels have emerged as a promising class of materials to target load‐bearing applications, where the material has to resist multiple cycles of extreme mechanical impact. A variety of chemical interactions and network architectures are used to enhance the mechanical properties and fracture mechanics of hydrogels making them stiffer and tougher. In recent years, the mechanical properties of tough, high‐performance hydrogels have been benchmarked, however, this is often incomplete as important variables like water content are largely ignored. In this review, the aim is to clarify the reported mechanical properties of state‐of‐the‐art tough hydrogels by providing a comprehensive library of fracture and mechanical property data. First, common methods for mechanical characterization of such high‐performance hydrogels are introduced. Then, various modes of energy dissipation to obtain tough hydrogels are discussed and used to categorize the individual datasets helping to asses the material's (fracture) mechanical properties. Finally, current applications are considered, tough high‐performance hydrogels are compared with existing materials, and promising future opportunities are discussed.