J. K. S. Svensson
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
J. K. S. Svensson has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
A. Memarpour
Höganäs AB, Global Process Development, Höganäs SE-263 83, Sweden
2 shared publicationsP. G. Jönsson
Division of Processes, KTH-Royal Institute of Technology, Stockholm SE-100 44, Sweden
2 shared publicationsV. Brabie
Material Science, Dalarna University, Falun SE-791 88, Sweden
2 shared publicationsF. Larsson
Outokumpu Stainless AB, Avesta SE-774 22, Sweden
1 shared publicationS. Ekerot
Division of Processes, KTH-Royal Institute of Technology, Stockholm SE-100 44, Sweden
1 shared publication
Latest Publications
- 9 November 2016
- Published by SAGE Publications in Ironmaking & Steelmaking: Processes, Products and Applications
- Vol. 45 (2) , 105-113
Implementation of an YSZ coating material to prevent clogging of the submerged entry nozzle (SEN) during continuous casting of Ce-treated steels
The possibility to reduce clogging in the submerged entry nozzle (SEN) during continuous casting of Ce alloyed stainless steels has been studied. This was done by implementing a new plasma coating material, consisting of yttria-stabilised zirconia (YSZ). The coating was first tested in pilot–plant trials; where the amount of steel teemed through the plasma-coated nozzles was monitored. Thereafter, samples of the coatings from the nozzles were studied using a FEG-SEM equipped with EDS. In addition, the coating material was tested in industrial trials where the performance was judged with respect to the clogging tendency detected as the movement of the stopper rod. The results from both the pilot–plant trials and industrial trials showed that the use of an YSZ coating led to a decreased clogging tendency during the casting in comparison to when using an uncoated SEN. Specifically, the pilot–plant trials showed that the clogging factor was lowered when implementing the YSZ coatings. Furthermore, the industrial trials showed that the clogging tendency, measured by the stopper rod movements, were lower when implementing the YSZ coating.
- 9 November 2016
- Published by SAGE Publications in Ironmaking & Steelmaking: Processes, Products and Applications
- Vol. 45 (2) , 105-113
Implementation of an YSZ coating material to prevent clogging of the submerged entry nozzle (SEN) during continuous casting of Ce-treated steels
The possibility to reduce clogging in the submerged entry nozzle (SEN) during continuous casting of Ce alloyed stainless steels has been studied. This was done by implementing a new plasma coating material, consisting of yttria-stabilised zirconia (YSZ). The coating was first tested in pilot–plant trials; where the amount of steel teemed through the plasma-coated nozzles was monitored. Thereafter, samples of the coatings from the nozzles were studied using a FEG-SEM equipped with EDS. In addition, the coating material was tested in industrial trials where the performance was judged with respect to the clogging tendency detected as the movement of the stopper rod. The results from both the pilot–plant trials and industrial trials showed that the use of an YSZ coating led to a decreased clogging tendency during the casting in comparison to when using an uncoated SEN. Specifically, the pilot–plant trials showed that the clogging factor was lowered when implementing the YSZ coatings. Furthermore, the industrial trials showed that the clogging tendency, measured by the stopper rod movements, were lower when implementing the YSZ coating.
- 18 March 2016
- Published by SAGE Publications in Ironmaking & Steelmaking: Processes, Products and Applications
- Vol. 44 (2) , 108-116
Studies of the decarburisation phenomena during preheating of submerged entry nozzles (SEN) in continuous casting processes
Decarburisation of the submerged entry nozzles (SEN) during the preheating process was investigated based on plant trials and thermodynamic modelling at three different steel plants. During the trials the preheating processes were mapped, the temperature profiles were registered and post-mortem studies of the SENs with scanning electron microscopy were performed. Typically, the glass/silicon powder will form a dense and protective layer inside the SEN when heated over 1100°C. However, this study found that the temperature distribution inside the SEN did not always reach this critical temperature. Thus, decarburisation of the SEN was found at all steel plants. The overall results illustrate that the control of the preheating process needs to be improved at all steel plants. It is suggested that future research should be focused on the development of new coating materials to prevent decarburisation of the refractory base material, which would decrease the chances of clogging during casting.
- 18 March 2016
- Published by SAGE Publications in Ironmaking & Steelmaking: Processes, Products and Applications
- Vol. 44 (2) , 108-116
Studies of the decarburisation phenomena during preheating of submerged entry nozzles (SEN) in continuous casting processes
Decarburisation of the submerged entry nozzles (SEN) during the preheating process was investigated based on plant trials and thermodynamic modelling at three different steel plants. During the trials the preheating processes were mapped, the temperature profiles were registered and post-mortem studies of the SENs with scanning electron microscopy were performed. Typically, the glass/silicon powder will form a dense and protective layer inside the SEN when heated over 1100°C. However, this study found that the temperature distribution inside the SEN did not always reach this critical temperature. Thus, decarburisation of the SEN was found at all steel plants. The overall results illustrate that the control of the preheating process needs to be improved at all steel plants. It is suggested that future research should be focused on the development of new coating materials to prevent decarburisation of the refractory base material, which would decrease the chances of clogging during casting.