Chien-Lung Liang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Chien-Lung Liang has a total of 55 co-authors. Here are the top co-authors by number of shared publications:
Kwang-Lung Lin
14 shared publications- Kwang-Lung Lin
Department of Materials Science and Engineering, National Cheng Kung University, Tainan, Taiwan
11 shared publications Meng-Chun Chiu
7 shared publicationsYung-Sheng Lin
Product Characterization, Corporate Research and Development (CRD), Advanced Semiconductor Engineering (ASE) Group, Kaohsiung, Taiwan
6 shared publicationsChin-Li Kao
4 shared publicationsDavid Tarng
4 shared publications
Latest Publications
- Open Access
- 2 February 2026
- Published by Springer Nature in JOM
- Vol. 78 (6) , 5415-5437
Electro-Recrystallization-Driven Microstructure, Twin Boundary Network, and Texture Evolution in Cold-Rolled Ni-20Cr Alloys Under Low-Temperature Electro-Treatment
The effects of direct-current electro-treatment on the microstructure and properties of cold-rolled Ni-20 wt.% Cr alloy were systematically investigated using electron backscatter diffraction (EBSD), a micro-Vickers hardness tester, and a four-point probe. Controlled current densities (1.2–1.8 × 10 4 A/cm 2 ) were applied to clarify the thresholds for electro-recrystallization and twin boundary evolution. Electro-recrystallization initiated at 1.2 × 10 4 A/cm 2 and completed at 1.4 × 10 4 A/cm 2 , accompanied by extensive formation of Σ3 annealing twin boundaries and texture transition from deformation to recrystallization components. At 1.8 × 10 4 A/cm 2 for 1 h, apparent grain growth occurred, with significant reductions in microhardness (− 56.8%) and electrical resistivity (− 33.1%) observed. In contrast, an isothermal thermal benchmark at the same treatment temperature produced negligible changes, confirming the dominant athermal electron-defect interaction as the primary driver of recrystallization. These findings demonstrate that direct-current electro-treatment enables low-temperature, energy-efficient recrystallization and twin-assisted grain boundary engineering, establishing Ni-20 wt.% Cr as a model system for current-assisted microstructure control in Inconel alloys.
- 2 February 2026
- Published by Springer Nature in JOM
- Vol. 78 (6) , 5415-5437
Open AccessElectro-Recrystallization-Driven Microstructure, Twin Boundary Network, and Texture Evolution in Cold-Rolled Ni-20Cr Alloys Under Low-Temperature Electro-Treatment
The effects of direct-current electro-treatment on the microstructure and properties of cold-rolled Ni-20 wt.% Cr alloy were systematically investigated using electron backscatter diffraction (EBSD), a micro-Vickers hardness tester, and a four-point probe. Controlled current densities (1.2–1.8 × 10 4 A/cm 2 ) were applied to clarify the thresholds for electro-recrystallization and twin boundary evolution. Electro-recrystallization initiated at 1.2 × 10 4 A/cm 2 and completed at 1.4 × 10 4 A/cm 2 , accompanied by extensive formation of Σ3 annealing twin boundaries and texture transition from deformation to recrystallization components. At 1.8 × 10 4 A/cm 2 for 1 h, apparent grain growth occurred, with significant reductions in microhardness (− 56.8%) and electrical resistivity (− 33.1%) observed. In contrast, an isothermal thermal benchmark at the same treatment temperature produced negligible changes, confirming the dominant athermal electron-defect interaction as the primary driver of recrystallization. These findings demonstrate that direct-current electro-treatment enables low-temperature, energy-efficient recrystallization and twin-assisted grain boundary engineering, establishing Ni-20 wt.% Cr as a model system for current-assisted microstructure control in Inconel alloys.
- 7 January 2026
- Published by Springer Nature in JOM
- Vol. 78 (6) , 5188-5206
Electromigration Reliability and Failure Mechanisms in Novel 3D Cu Stagger-via Interconnects for Advanced High-Density Fan-Out Packaging
- 7 January 2026
- Published by Springer Nature in JOM
- Vol. 78 (6) , 5188-5206
Electromigration Reliability and Failure Mechanisms in Novel 3D Cu Stagger-via Interconnects for Advanced High-Density Fan-Out Packaging
- 10 December 2025
- Published by Elsevier in Ceramics International
- Vol. 52 (3) , 3459-3469
Activated alumina recycled from industrial aluminum dross via phase-controlled thermal activation
- 10 December 2025
- Published by Elsevier in Ceramics International
- Vol. 52 (3) , 3459-3469
Activated alumina recycled from industrial aluminum dross via phase-controlled thermal activation
- Open Access
- 13 November 2025
- Published by Springer Nature in JOM
- Vol. 78 (6) , 5369-5391
The Impact of Direct-Current Electro-Treatment on the Microstructure and Mechanical Behavior of Cold-Rolled 2014 Aluminum Alloys
Electrically assisted post-processing is proposed as an energy-efficient alternative to conventional thermal annealing for tailoring the mechanical properties of cold-rolled AA2014 aluminum alloys. Cold-rolled strips were subjected to direct current at current densities ranging from 1.4 to 2.0 × 10 4 A/cm 2 for 60 min, and the resulting microstructural evolutions were characterized by electron backscatter diffraction, focusing on grain microstructures, residual strain, grain-boundary characteristics, and textures. The results revealed a distinct transition from recovery-dominated processes at relatively low current densities (1.4–1.6 × 10 4 A/cm 2 ) to recrystallization and grain growth accompanied by texture randomization at higher current densities (1.8–2.0 × 10 4 A/cm 2 ). Significant micro-hardness reductions, up to 48.7% relative to the cold-rolled state, were achieved, reaching values comparable to the solution-treated benchmark at 500°C. Thermal benchmark experiments further demonstrated that the observed microstructural transformation was attributed to the synergistic thermal and athermal effects, highlighting that Joule heating alone could not reproduce the extent of recrystallization. These findings confirm electro-treatment (ET) as a potential route for efficient microstructure control and mechanical property tailoring in AA2014, offering both performance benefits and reduced energy consumption of 95.7% compared to conventional thermal annealing treatment for advanced manufacturing applications.
- 13 November 2025
- Published by Springer Nature in JOM
- Vol. 78 (6) , 5369-5391
Open AccessThe Impact of Direct-Current Electro-Treatment on the Microstructure and Mechanical Behavior of Cold-Rolled 2014 Aluminum Alloys
Electrically assisted post-processing is proposed as an energy-efficient alternative to conventional thermal annealing for tailoring the mechanical properties of cold-rolled AA2014 aluminum alloys. Cold-rolled strips were subjected to direct current at current densities ranging from 1.4 to 2.0 × 10 4 A/cm 2 for 60 min, and the resulting microstructural evolutions were characterized by electron backscatter diffraction, focusing on grain microstructures, residual strain, grain-boundary characteristics, and textures. The results revealed a distinct transition from recovery-dominated processes at relatively low current densities (1.4–1.6 × 10 4 A/cm 2 ) to recrystallization and grain growth accompanied by texture randomization at higher current densities (1.8–2.0 × 10 4 A/cm 2 ). Significant micro-hardness reductions, up to 48.7% relative to the cold-rolled state, were achieved, reaching values comparable to the solution-treated benchmark at 500°C. Thermal benchmark experiments further demonstrated that the observed microstructural transformation was attributed to the synergistic thermal and athermal effects, highlighting that Joule heating alone could not reproduce the extent of recrystallization. These findings confirm electro-treatment (ET) as a potential route for efficient microstructure control and mechanical property tailoring in AA2014, offering both performance benefits and reduced energy consumption of 95.7% compared to conventional thermal annealing treatment for advanced manufacturing applications.
- 5 September 2025
- Published by Elsevier in Materials Letters
- Vol. 403
Enhanced recrystallization efficiency in cold-rolled pure copper via electrical annealing: a kinetics study
- 5 September 2025
- Published by Elsevier in Materials Letters
- Vol. 403
Enhanced recrystallization efficiency in cold-rolled pure copper via electrical annealing: a kinetics study
- 9 September 2024
- Published by Elsevier in Materials Letters
- Vol. 377
Current-induced strengthening and softening behaviors in 7075 aluminum alloys with electro-treatment
- 9 September 2024
- Published by Elsevier in Materials Letters
- Vol. 377
Current-induced strengthening and softening behaviors in 7075 aluminum alloys with electro-treatment