Jonghyeon Sohn
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Jonghyeon Sohn has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
Nogill Park
3 shared publicationsSanggon Moon
2 shared publications- Suchul Kim
Department of Industrial Machinery DX, Korea Institute of Machinery and Materials, Daejeon, South Korea
2 shared publications Chan-Ho Choi
1 shared publicationChunghan Oh
1 shared publication- Dong Il Park
Korea Institute of Machinery and Materials
1 shared publication
Latest Publications
- Open Access
- 26 June 2025
- Published by Elsevier in Mechanism and Machine Theory
- Vol. 214
Optimal design strategy for gear pairs integrating macro and micro geometry optimization
- 26 June 2025
- Published by Elsevier in Mechanism and Machine Theory
- Vol. 214
Open AccessOptimal design strategy for gear pairs integrating macro and micro geometry optimization
- Open Access
- 30 April 2023
- Published by Computational Structural Engineering Institute of Korea in Journal of the Computational Structural Engineering Institute of Korea
- Vol. 36 (2) , 121-130
Analysis of the Transmission Error of Spur Gears Depending on the Finite Element Analysis Condition
Finite element analysis is widely used to predict the structural stability and tooth contact performance of gears. This study focused on the effect of finite element modeling conditions of a spur gear on the simulation result and the model simplification. The gear body and teeth, teeth width, configuration of mesh, frictional coefficient, and simulation time interval (gear mesh cycle division) were selected for model simplification for gear analysis. The static transmission error during a single-gear mesh cycle was calculated to represent the performance of the gear, and the elapsed time was measured as a simplification factor. Contact stress distribution was also checked. The differences in maximum transmission error and elapsed time depending on the model simplification methods were analyzed. After all simplification methods were estimated, an optimal combination of the methods was defined, and the result was compared with that of the most detailed modeling methods.
- 30 April 2023
- Published by Computational Structural Engineering Institute of Korea in Journal of the Computational Structural Engineering Institute of Korea
- Vol. 36 (2) , 121-130
Open AccessAnalysis of the Transmission Error of Spur Gears Depending on the Finite Element Analysis Condition
Finite element analysis is widely used to predict the structural stability and tooth contact performance of gears. This study focused on the effect of finite element modeling conditions of a spur gear on the simulation result and the model simplification. The gear body and teeth, teeth width, configuration of mesh, frictional coefficient, and simulation time interval (gear mesh cycle division) were selected for model simplification for gear analysis. The static transmission error during a single-gear mesh cycle was calculated to represent the performance of the gear, and the elapsed time was measured as a simplification factor. Contact stress distribution was also checked. The differences in maximum transmission error and elapsed time depending on the model simplification methods were analyzed. After all simplification methods were estimated, an optimal combination of the methods was defined, and the result was compared with that of the most detailed modeling methods.
- Open Access
- 17 July 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (14) , 6582
Statistical Analysis for Transmission Error of Gear System with Mechanical and Thermal Deformation Uncertainties
We establish a robust algorithm to analyze the influence of system uncertainties on the transmission error of a spur gear pair under 2D simplification. The algorithm provides a way of generating smooth cutter profiles with machining uncertainties and measuring the thermal deformation through the uncertainties in material properties. Then, it produces realizations of gear tooth profiles based on the analytical method for accuracy and computational efficiency. Numerical investigations show the statistical analysis on the tooth contact analysis by comparing steel and plastic gears. It is worthwhile remarking that the plastic gear is susceptible to the geometric error caused by thermal deformation. Moreover, although the impact of thermal deformation on steel gear may seem slim, it can have a noticeable influence when it exists with mechanical uncertainties together.
- 17 July 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (14) , 6582
Open AccessStatistical Analysis for Transmission Error of Gear System with Mechanical and Thermal Deformation Uncertainties
We establish a robust algorithm to analyze the influence of system uncertainties on the transmission error of a spur gear pair under 2D simplification. The algorithm provides a way of generating smooth cutter profiles with machining uncertainties and measuring the thermal deformation through the uncertainties in material properties. Then, it produces realizations of gear tooth profiles based on the analytical method for accuracy and computational efficiency. Numerical investigations show the statistical analysis on the tooth contact analysis by comparing steel and plastic gears. It is worthwhile remarking that the plastic gear is susceptible to the geometric error caused by thermal deformation. Moreover, although the impact of thermal deformation on steel gear may seem slim, it can have a noticeable influence when it exists with mechanical uncertainties together.
- 31 December 2020
- Published by The Korean Society for Aeronautical & Space Sciences in Journal of the Korean Society for Aeronautical & Space Sciences
- Vol. 48 (12) , 953-960
Optimization of Gear Webs for Rotorcraft Engine Reduction Gear Train
본 논문은 회전익기용 엔진 감속기 주 기어열의 기어 웹 형상 최적화에 대해 기술하였다. 최적화 목표는 총중량, 전달 오차, 정렬 오차, 치면 하중 분포 계수 값의 최소화로 설정하였으며, 기어의 웹 두께, 웹과 축의 연결 위치, 웹과 림의 연결 위치를 설계변수로 선정하였다. 최적화 과정에서 기어의 웹, 축, 림은 3D 캐드 모델로부터 유한요소 모델로 변환되었으며, 기어 해석 프로그램 MASTA에 입력되었다. 최적화 알고리즘은 NSGA-Ⅱ를 사용하였다. 최적화 결과 주 기어열의 총 중량, 전달 오차, 정렬 오차, 치면 하중 분포 계수 값은 모두 감소하였으며, 최대 응력도 안전한 수준으로 나타나서 전반적으로 기어 성능이 개선되었음을 확인하였다.
- 31 December 2020
- Published by The Korean Society for Aeronautical & Space Sciences in Journal of the Korean Society for Aeronautical & Space Sciences
- Vol. 48 (12) , 953-960
Optimization of Gear Webs for Rotorcraft Engine Reduction Gear Train
본 논문은 회전익기용 엔진 감속기 주 기어열의 기어 웹 형상 최적화에 대해 기술하였다. 최적화 목표는 총중량, 전달 오차, 정렬 오차, 치면 하중 분포 계수 값의 최소화로 설정하였으며, 기어의 웹 두께, 웹과 축의 연결 위치, 웹과 림의 연결 위치를 설계변수로 선정하였다. 최적화 과정에서 기어의 웹, 축, 림은 3D 캐드 모델로부터 유한요소 모델로 변환되었으며, 기어 해석 프로그램 MASTA에 입력되었다. 최적화 알고리즘은 NSGA-Ⅱ를 사용하였다. 최적화 결과 주 기어열의 총 중량, 전달 오차, 정렬 오차, 치면 하중 분포 계수 값은 모두 감소하였으며, 최대 응력도 안전한 수준으로 나타나서 전반적으로 기어 성능이 개선되었음을 확인하였다.
- 1 November 2017
- Published by Elsevier in Mechanism and Machine Theory
- Vol. 117, 133-147
Modified worm gear hobbing for symmetric longitudinal crowning in high lead cylindrical worm gear drives
- 1 November 2017
- Published by Elsevier in Mechanism and Machine Theory
- Vol. 117, 133-147
Modified worm gear hobbing for symmetric longitudinal crowning in high lead cylindrical worm gear drives
- 28 September 2016
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 231 (24) , 4646-4654
Study on the influence of gear hobbing and shaft misalignments on the geometric interference of cylindrical worm gear set
Geometric interference can occur in cylindrical worm gear set that makes use of oversized hob to cut the worm gear. In particular, the interference occurs easily in the design with high lead and low pressure angles. The interference results in a corner contact. In this study, we examined the influence of the machine tool setting errors of the worm gear hobbing and the influence of the shaft misalignments of the worm gear set on the interference. To determine the interference, we used the surface separation topology based on differential geometry. In addition, we also examined the hob oversize range required to avoid the interference under the condition of the machine tool setting errors and shaft misalignments. This study found that the interference can be avoided not only when the hob oversize is larger than the upper limit, but also when the hob oversize is smaller than the lower limit. This study also found that the interference can be avoided by applying the intended errors on the machine tool setting and shaft alignment, without manipulating the hob oversize.
- 28 September 2016
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 231 (24) , 4646-4654
Study on the influence of gear hobbing and shaft misalignments on the geometric interference of cylindrical worm gear set
Geometric interference can occur in cylindrical worm gear set that makes use of oversized hob to cut the worm gear. In particular, the interference occurs easily in the design with high lead and low pressure angles. The interference results in a corner contact. In this study, we examined the influence of the machine tool setting errors of the worm gear hobbing and the influence of the shaft misalignments of the worm gear set on the interference. To determine the interference, we used the surface separation topology based on differential geometry. In addition, we also examined the hob oversize range required to avoid the interference under the condition of the machine tool setting errors and shaft misalignments. This study found that the interference can be avoided not only when the hob oversize is larger than the upper limit, but also when the hob oversize is smaller than the lower limit. This study also found that the interference can be avoided by applying the intended errors on the machine tool setting and shaft alignment, without manipulating the hob oversize.
- 1 June 2016
- Published by Elsevier in Mechanism and Machine Theory
- Vol. 100, 83-103
Geometric interference in cylindrical worm gear drives using oversized hob to cut worm gears
- 1 June 2016
- Published by Elsevier in Mechanism and Machine Theory
- Vol. 100, 83-103
Geometric interference in cylindrical worm gear drives using oversized hob to cut worm gears
- 1 January 2014
- Published by The Korean Society of Automotive Engineers in Transaction of the Korean Society of Automotive Engineers
- Vol. 22 (1) , 77-84
Design of Worm Gear for CVVL Paired with ZK Worm and Involute Helical Gear
- 1 January 2014
- Published by The Korean Society of Automotive Engineers in Transaction of the Korean Society of Automotive Engineers
- Vol. 22 (1) , 77-84
Design of Worm Gear for CVVL Paired with ZK Worm and Involute Helical Gear