Suchul Kim
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Suchul Kim has a total of 38 co-authors. Here are the top co-authors by number of shared publications:
Sanggon Moon
Department of Industrial Machinery DX, Korea Institute of Machinery and Materials, Daejeon, Republic of Korea
4 shared publicationsGeunho Lee
Principal Researcher, Department of Smart Industrial Machine Technology, Korea Institute of Machinery & Materials, Deajeon, 34103, Korea
3 shared publications- Young-Jun Park
Department of Biosystems Engineering, Seoul National University, Seoul, Republic of Korea
3 shared publications Chan-Ho Choi
2 shared publicationsDonggun Lee
Department of Bio-Industrial Mechanical Engineering, Kyungpook National University, Daegu, South Korea
2 shared publicationsHoungjong Ahn
Tractor Advanced Development Group, LS Mtron, Anyang, South Korea
2 shared publications
Latest Publications
- Open Access
- 9 April 2026
- Published by Springer Nature in Scientific Reports
- Vol. 16 (1) , 11835
Prediction and reduction of dynamic factor based on dynamic behavior of gear systems
Gears operating at high rotational speeds are prone to resonance-induced load amplification, which can significantly shorten their service life. This study quantifies the dynamic factor (\(\:{K}_{v}\)) of a spur gear pair operating between 500 and 4,000 rpm by combining high-fidelity dynamics simulations with targeted experiments. The simulation model, validated against experimentally measured dynamic meshing forces, accurately reproduces the primary resonance at 3,450 rpm with a mere 2.48% error in \(\:{K}_{v}\). A comparison with calculations based on ISO 6336 Method B reveals that this standard tends to overestimate both the resonance speed and \(\:{K}_{v}\), leading to unnecessarily conservative designs. Parametric studies show that increasing the torque from 100 N·m to 500 N·m reduces \(\:{K}_{v}\) by up to 14%, while crowning that reduces the peak-to-peak transmission error from 4.5 μm to 2.0 μm attenuates \(\:{K}_{v}\) by 22% and suppresses contact stress amplification. These findings demonstrate that validated simulations enable more accurate resonance prediction and promote more weight-efficient gear design for high-speed applications than empirical ISO formulas.- 9 April 2026
- Published by Springer Nature in Scientific Reports
- Vol. 16 (1) , 11835
Open AccessPrediction and reduction of dynamic factor based on dynamic behavior of gear systems
Gears operating at high rotational speeds are prone to resonance-induced load amplification, which can significantly shorten their service life. This study quantifies the dynamic factor (\(\:{K}_{v}\)) of a spur gear pair operating between 500 and 4,000 rpm by combining high-fidelity dynamics simulations with targeted experiments. The simulation model, validated against experimentally measured dynamic meshing forces, accurately reproduces the primary resonance at 3,450 rpm with a mere 2.48% error in \(\:{K}_{v}\). A comparison with calculations based on ISO 6336 Method B reveals that this standard tends to overestimate both the resonance speed and \(\:{K}_{v}\), leading to unnecessarily conservative designs. Parametric studies show that increasing the torque from 100 N·m to 500 N·m reduces \(\:{K}_{v}\) by up to 14%, while crowning that reduces the peak-to-peak transmission error from 4.5 μm to 2.0 μm attenuates \(\:{K}_{v}\) by 22% and suppresses contact stress amplification. These findings demonstrate that validated simulations enable more accurate resonance prediction and promote more weight-efficient gear design for high-speed applications than empirical ISO formulas. - Open Access
- 13 January 2026
- Published by Springer Nature in Research Square
Prediction and reduction of dynamic factor based on dynamic behavior of gear systems
Gears operating at high rotational speeds are prone to resonance-induced load amplification, which can significantly shorten their service life. This study quantifies the dynamic factor (\(\:{K}_{v}\)) of a spur gear pair operating between 500 and 4,000 rpm by combining high-fidelity dynamics simulations with targeted experiments. The simulation model, validated against experimentally measured dynamic meshing forces, accurately reproduces the primary resonance at 3,450 rpm with a mere 2.5% error in \(\:{K}_{v}\). A comparison with calculations based on ISO 6336 Method B reveals that this standard tends to overestimate both the resonance speed and \(\:{K}_{v}\), leading to unnecessarily conservative designs. Parametric studies show that increasing the torque from 100 N·m to 500 N·m reduces \(\:{K}_{v}\) by up to 14%, while crowning that reduces the peak-to-peak transmission error from 4.5 µm to 2.0 µm attenuates \(\:{K}_{v}\) by 22% and suppresses contact stress amplification. These findings demonstrate that validated simulations enable more accurate resonance prediction and promote more weight-efficient gear design for high-speed applications than empirical ISO formulas.- 13 January 2026
- Published by Springer Nature in Research Square
Open AccessPrediction and reduction of dynamic factor based on dynamic behavior of gear systems
Gears operating at high rotational speeds are prone to resonance-induced load amplification, which can significantly shorten their service life. This study quantifies the dynamic factor (\(\:{K}_{v}\)) of a spur gear pair operating between 500 and 4,000 rpm by combining high-fidelity dynamics simulations with targeted experiments. The simulation model, validated against experimentally measured dynamic meshing forces, accurately reproduces the primary resonance at 3,450 rpm with a mere 2.5% error in \(\:{K}_{v}\). A comparison with calculations based on ISO 6336 Method B reveals that this standard tends to overestimate both the resonance speed and \(\:{K}_{v}\), leading to unnecessarily conservative designs. Parametric studies show that increasing the torque from 100 N·m to 500 N·m reduces \(\:{K}_{v}\) by up to 14%, while crowning that reduces the peak-to-peak transmission error from 4.5 µm to 2.0 µm attenuates \(\:{K}_{v}\) by 22% and suppresses contact stress amplification. These findings demonstrate that validated simulations enable more accurate resonance prediction and promote more weight-efficient gear design for high-speed applications than empirical ISO formulas. - 22 August 2025
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
- Vol. 240 (8) , 5745-5756
Temperature prediction of multi-plate wet clutch by artificial neural network with heat transfer differential equation
This study proposes a novel methodology for predicting the temperature of a multi-plate wet clutch by integrating artificial neural networks with heat transfer differential equations. Traditional approaches for clutch temperature prediction, such as empirical models and finite element methods, are often limited by high computational costs and simplified assumptions. In contrast, this research combines physical laws with neural networks to enhance prediction accuracy. Using experimental data obtained from a wet clutch, LSTM-based neural network was trained to estimate convective heat transfer coefficients dynamically, incorporating factors such as friction plate internal and external diameter, rotational speed, lubricant flow rate, inlet lubricant temperature, and groove type. The predicted coefficients were then applied to solve the heat transfer differential equation, ensuring the physical validity of the temperature predictions. Comparative evaluations demonstrated that the proposed neural network model with heat transfer integration outperformed existing empirical and neural network-only models, achieving a 69.68% reduction in MSE and a 64.27% reduction in RMSE compared to the empirical model.
- 22 August 2025
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
- Vol. 240 (8) , 5745-5756
Temperature prediction of multi-plate wet clutch by artificial neural network with heat transfer differential equation
This study proposes a novel methodology for predicting the temperature of a multi-plate wet clutch by integrating artificial neural networks with heat transfer differential equations. Traditional approaches for clutch temperature prediction, such as empirical models and finite element methods, are often limited by high computational costs and simplified assumptions. In contrast, this research combines physical laws with neural networks to enhance prediction accuracy. Using experimental data obtained from a wet clutch, LSTM-based neural network was trained to estimate convective heat transfer coefficients dynamically, incorporating factors such as friction plate internal and external diameter, rotational speed, lubricant flow rate, inlet lubricant temperature, and groove type. The predicted coefficients were then applied to solve the heat transfer differential equation, ensuring the physical validity of the temperature predictions. Comparative evaluations demonstrated that the proposed neural network model with heat transfer integration outperformed existing empirical and neural network-only models, achieving a 69.68% reduction in MSE and a 64.27% reduction in RMSE compared to the empirical model.
- Open Access
- 26 June 2025
- Published by Elsevier in Mechanism and Machine Theory
- Vol. 214
Optimal design strategy for gear pairs integrating macro and micro geometry optimization
- 26 June 2025
- Published by Elsevier in Mechanism and Machine Theory
- Vol. 214
Open AccessOptimal design strategy for gear pairs integrating macro and micro geometry optimization
- Open Access
- 29 March 2024
- Published by MDPI AG in Agriculture
- Vol. 14 (4) , 544
Development of a Modified Method for Measuring the Actual Draft Force Using a Tractor-Attached Dynamometer
In this study, crank-locker kinematic equations were used to analyze the three-point hitch behavior when the dynamometer was connected to the work machine. The dynamometer was statically tested with a hydraulic actuator, and the accuracy of the three-way force and the moment was confirmed to be 96–99%. The calibrated dynamometer was put to the test on a real farm field, and data were collected using a data acquisition system. Using the transport pitch correction equation, the collected data can be transformed into more realistic data. International standards were used to determine the point of connection between the tractor, dynamometer, and implement. The results of this study made it possible to accurately measure force and moment, which will have an important role in future agricultural technologies such as autonomous agricultural operation.
- 29 March 2024
- Published by MDPI AG in Agriculture
- Vol. 14 (4) , 544
Open AccessDevelopment of a Modified Method for Measuring the Actual Draft Force Using a Tractor-Attached Dynamometer
In this study, crank-locker kinematic equations were used to analyze the three-point hitch behavior when the dynamometer was connected to the work machine. The dynamometer was statically tested with a hydraulic actuator, and the accuracy of the three-way force and the moment was confirmed to be 96–99%. The calibrated dynamometer was put to the test on a real farm field, and data were collected using a data acquisition system. Using the transport pitch correction equation, the collected data can be transformed into more realistic data. International standards were used to determine the point of connection between the tractor, dynamometer, and implement. The results of this study made it possible to accurately measure force and moment, which will have an important role in future agricultural technologies such as autonomous agricultural operation.
- Open Access
- 10 June 2023
- Published by MDPI AG in Agriculture
- Vol. 13 (6) , 1225
Theoretical Calculations and Experimental Studies of Power Loss in Dual-Clutch Transmission of Agricultural Tractors
Recent carbon neutrality policies have led to active research in the agricultural tractor sector to replace internal combustion engines, making it imperative to minimize power losses to improve efficiency. Dual-clutch transmissions (DCTs) have been employed in agricultural tractors primarily due to their short shift time and smooth shift feel. However, DCTs have a relatively large number of components and complex structures owing to spatial constraints, making it challenging to predict power losses. Therefore, to predict DCT power losses, this study defined oil churning by considering the structural characteristics and oil circulation and comparing and analyzing the theoretical calculation and test results of power losses at different oil levels. Power loss was calculated based on ISO standards and fluid viscosity theory, and tests were performed to verify. We calculated power losses based on the defined oil churning of a DCT in agricultural tractors and confirmed that their consistency in test results improved when reflecting the lubrication state, considering the structural features and oil circulation. In addition, the factors contributing to power loss under low- and high-speed conditions were analyzed by calculating the power loss for each component.
- 10 June 2023
- Published by MDPI AG in Agriculture
- Vol. 13 (6) , 1225
Open AccessTheoretical Calculations and Experimental Studies of Power Loss in Dual-Clutch Transmission of Agricultural Tractors
Recent carbon neutrality policies have led to active research in the agricultural tractor sector to replace internal combustion engines, making it imperative to minimize power losses to improve efficiency. Dual-clutch transmissions (DCTs) have been employed in agricultural tractors primarily due to their short shift time and smooth shift feel. However, DCTs have a relatively large number of components and complex structures owing to spatial constraints, making it challenging to predict power losses. Therefore, to predict DCT power losses, this study defined oil churning by considering the structural characteristics and oil circulation and comparing and analyzing the theoretical calculation and test results of power losses at different oil levels. Power loss was calculated based on ISO standards and fluid viscosity theory, and tests were performed to verify. We calculated power losses based on the defined oil churning of a DCT in agricultural tractors and confirmed that their consistency in test results improved when reflecting the lubrication state, considering the structural features and oil circulation. In addition, the factors contributing to power loss under low- and high-speed conditions were analyzed by calculating the power loss for each component.
- Open Access
- 30 April 2023
- Published by Computational Structural Engineering Institute of Korea in Journal of the Computational Structural Engineering Institute of Korea
- Vol. 36 (2) , 121-130
Analysis of the Transmission Error of Spur Gears Depending on the Finite Element Analysis Condition
Finite element analysis is widely used to predict the structural stability and tooth contact performance of gears. This study focused on the effect of finite element modeling conditions of a spur gear on the simulation result and the model simplification. The gear body and teeth, teeth width, configuration of mesh, frictional coefficient, and simulation time interval (gear mesh cycle division) were selected for model simplification for gear analysis. The static transmission error during a single-gear mesh cycle was calculated to represent the performance of the gear, and the elapsed time was measured as a simplification factor. Contact stress distribution was also checked. The differences in maximum transmission error and elapsed time depending on the model simplification methods were analyzed. After all simplification methods were estimated, an optimal combination of the methods was defined, and the result was compared with that of the most detailed modeling methods.
- 30 April 2023
- Published by Computational Structural Engineering Institute of Korea in Journal of the Computational Structural Engineering Institute of Korea
- Vol. 36 (2) , 121-130
Open AccessAnalysis of the Transmission Error of Spur Gears Depending on the Finite Element Analysis Condition
Finite element analysis is widely used to predict the structural stability and tooth contact performance of gears. This study focused on the effect of finite element modeling conditions of a spur gear on the simulation result and the model simplification. The gear body and teeth, teeth width, configuration of mesh, frictional coefficient, and simulation time interval (gear mesh cycle division) were selected for model simplification for gear analysis. The static transmission error during a single-gear mesh cycle was calculated to represent the performance of the gear, and the elapsed time was measured as a simplification factor. Contact stress distribution was also checked. The differences in maximum transmission error and elapsed time depending on the model simplification methods were analyzed. After all simplification methods were estimated, an optimal combination of the methods was defined, and the result was compared with that of the most detailed modeling methods.
- 22 February 2023
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 237 (20) , 4666-4681
An efficient process for macro geometry optimization of helical gear pairs considering static transmission error
Loaded tooth contact analysis (LTCA) adopted to obtain the static transmission error for the gear optimization affects significantly the computation time and results. This paper is to study an efficient process of macro geometry optimization of helical gear pairs with LTCA. An analytical LTCA model was proposed and verified with the measured transmission error. To find an efficient LTCA method, the proposed model was divided into three types (based on whether the slice stiffness and extended contact were included) by adjusting the fidelity. When extended contact was included in LTCA, the increased computation time was very short, but the accuracy of the results improved significantly. Optimization processes were designed based on the analysis results, and it was most efficient when starting with the model considering only the extended contact and ending 5%−10% of the entire generation with the highest fidelity model. In the process, the computational effort was significantly reduced compared to when the optimization process was configured with only the highest fidelity model, and the level of optimization was almost equal.
- 22 February 2023
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 237 (20) , 4666-4681
An efficient process for macro geometry optimization of helical gear pairs considering static transmission error
Loaded tooth contact analysis (LTCA) adopted to obtain the static transmission error for the gear optimization affects significantly the computation time and results. This paper is to study an efficient process of macro geometry optimization of helical gear pairs with LTCA. An analytical LTCA model was proposed and verified with the measured transmission error. To find an efficient LTCA method, the proposed model was divided into three types (based on whether the slice stiffness and extended contact were included) by adjusting the fidelity. When extended contact was included in LTCA, the increased computation time was very short, but the accuracy of the results improved significantly. Optimization processes were designed based on the analysis results, and it was most efficient when starting with the model considering only the extended contact and ending 5%−10% of the entire generation with the highest fidelity model. In the process, the computational effort was significantly reduced compared to when the optimization process was configured with only the highest fidelity model, and the level of optimization was almost equal.
- Open Access
- 30 September 2022
- Published by The Korean Society of Manufacturing Process Engineers in Journal of the Korean Society of Manufacturing Process Engineers
- Vol. 21 (9) , 21-27
Gear Macro Geometry Optimization of Rotorcraft Engine Gearbox
- 30 September 2022
- Published by The Korean Society of Manufacturing Process Engineers in Journal of the Korean Society of Manufacturing Process Engineers
- Vol. 21 (9) , 21-27
Open AccessGear Macro Geometry Optimization of Rotorcraft Engine Gearbox
- 29 July 2022
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 23 (9) , 1049-1063
Bolt Strength Evaluation of Tractor Rear Axle Based on Simulation Model
- 29 July 2022
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 23 (9) , 1049-1063
Bolt Strength Evaluation of Tractor Rear Axle Based on Simulation Model