Philipp Junker
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Philipp Junker has a total of 128 co-authors. Here are the top co-authors by number of shared publications:
Klaus Hackl
Institute of Mechanics of Materials, Ruhr-Universität Bochum, Bochum, Germany
35 shared publications- Dustin Roman Jantos
Institute of Continuum Mechanics Leibniz University Hannover Garbsen Germany
17 shared publications - Klaus Hackl
Institute of Mechanics of Materials Ruhr‐Universitat Bochum Bochum Germany
14 shared publications - Johanna Waimann
Institute of Mechanics of Materials Ruhr‐Universitat Bochum Bochum Germany
10 shared publications - Markus Kästner
TU Dresden
10 shared publications - Stephan Schwarz
Lehrstuhl für Mechanik – Materialtheorie, Ruhr-Universität Bochum, Bochum, Germany
10 shared publications
Latest Publications
- 2 September 2026
- Published by Springer Nature
- p. 81-102
Schwerpunkt
- 2 September 2026
- Published by Springer Nature
- p. 103-135
Lagerreaktionen
- 2 September 2026
- Published by Springer Nature
- p. 137-156
Fachwerke
- 2 September 2026
- Published by Springer Nature
- p. 235-253
Haftung und Reibung
- 2 September 2026
- Published by Springer Nature
- p. 1-12
Grundbegriffe
- 2 September 2026
- Published by Springer Nature
- p. 39-80
Allgemeine Kraftsysteme und Gleichgewicht des starren Körpers
- 2 September 2026
- Published by Springer Nature
- p. 39-80
Allgemeine Kraftsysteme und Gleichgewicht des starren Körpers
- 2 September 2026
- Published by Springer Nature
- p. 13-37
Kräfte mit gemeinsamem Angriffspunkt
- 2 September 2026
- Published by Springer Nature
- p. 203-233
Arbeit
- 2 September 2026
- Published by Springer Nature
- p. 157-201
Balken, Rahmen, Bogen
- Open Access
- 30 August 2026
- Published by Wiley in Proceedings in Applied Mathematics and Mechanics
- Vol. 26 (4) , e70197
Topology, Orientation and Fiber Path Optimization for Layered Anisotropic Materials
Topology optimization and additive manufacturing complement each other: the freedom offered by design optimization enables the creation of complex, highly efficient structures that are often feasible only with additive manufacturing. However, most structural optimization methods assume isotropic material properties, an assumption that contradicts the inherent anisotropy of structures produced via additive manufacturing. Therefore, a comprehensive optimization should consider not only the topology but also the local material orientation. We present an optimization approach for the topology of layered, anisotropic materials that includes optimizing the global print plane and the local fiber or tool paths, as well as restricting the maximum fiber curvature within the layers. This approach is grounded in thermodynamic optimization based on the stationarity condition of a variational principle used in thermodynamically consistent material modeling. We derive transient partial differential equations for the design variables, whose solutions in pseudo‐time serve as an update scheme that drives the design variables toward the optimum.
- 30 August 2026
- Published by Wiley in Proceedings in Applied Mathematics and Mechanics
- Vol. 26 (4) , e70197
Open AccessTopology, Orientation and Fiber Path Optimization for Layered Anisotropic Materials
Topology optimization and additive manufacturing complement each other: the freedom offered by design optimization enables the creation of complex, highly efficient structures that are often feasible only with additive manufacturing. However, most structural optimization methods assume isotropic material properties, an assumption that contradicts the inherent anisotropy of structures produced via additive manufacturing. Therefore, a comprehensive optimization should consider not only the topology but also the local material orientation. We present an optimization approach for the topology of layered, anisotropic materials that includes optimizing the global print plane and the local fiber or tool paths, as well as restricting the maximum fiber curvature within the layers. This approach is grounded in thermodynamic optimization based on the stationarity condition of a variational principle used in thermodynamically consistent material modeling. We derive transient partial differential equations for the design variables, whose solutions in pseudo‐time serve as an update scheme that drives the design variables toward the optimum.