Juha Kostamovaara
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Juha Kostamovaara has a total of 67 co-authors. Here are the top co-authors by number of shared publications:
- Pekka Keranen
Circuits and Systems Research Unit, UNIVERSITY OF OULU, Oulu, Finland
9 shared publications - Lauri Hallman
Univ. of Oulu (Finland)
8 shared publications - Jussi-Pekka Jansson
Circuits and Systems Research Unit, UNIVERSITY OF OULU, Oulu, Finland
6 shared publications - Sahba Jahromi
Murata Electronics Oy, Vantaa, Finland
6 shared publications - Sergey N. Vainshtein
Department of Electronics and Nanoengineering, MilliLab, Aalto University, Aalto, Finland
5 shared publications - Aram Baharmast
Circuits and Systems Research Unit, UNIVERSITY OF OULU, Oulu, Finland
3 shared publications
Latest Publications
- Open Access
- 17 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 18 (2) , 1-12
On Pulsed Time-of-Flight Laser Ranging With Sub-ns Laser Pulses and an Off–Focal Plane Digital CMOS SPAD Receiver
Pulsed time-of-flight lidar techniques based on the use of a gain-switched laser diode as a transmitter and a digital CMOS SPAD array with 9 × 9 SPAD unit elements and 10 time-to-digital converters are presented. The laser transmitter produces laser pulses with pulse energy, pulse width and repetition rate of 350 pJ, 65 ps and 100 kHz, respectively. The receiver uses a small aperture as a field stop to match the transmitter and receiver fields-of-view. The CMOS detector with the 9 × 9 SPAD unit elements is placed behind the focal plane in order to lower the random background detection rate of a single SPAD unit element. Thus, the possibility for detector blocking is also reduced in high background illumination conditions. Measurements show that the presented setup allows a distance measurement range of up to ∼90 meters to a target of brushed gray concrete in bright sunlight conditions (60 – 70 klux) with 5600 laser pulses sent and only activating a sub-array of 3 × 3 SPADs and 10 TDCs in the receiver. The measurement precision (σ-value) is in the millimeter range.
- 17 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 18 (2) , 1-12
Open AccessOn Pulsed Time-of-Flight Laser Ranging With Sub-ns Laser Pulses and an Off–Focal Plane Digital CMOS SPAD Receiver
Pulsed time-of-flight lidar techniques based on the use of a gain-switched laser diode as a transmitter and a digital CMOS SPAD array with 9 × 9 SPAD unit elements and 10 time-to-digital converters are presented. The laser transmitter produces laser pulses with pulse energy, pulse width and repetition rate of 350 pJ, 65 ps and 100 kHz, respectively. The receiver uses a small aperture as a field stop to match the transmitter and receiver fields-of-view. The CMOS detector with the 9 × 9 SPAD unit elements is placed behind the focal plane in order to lower the random background detection rate of a single SPAD unit element. Thus, the possibility for detector blocking is also reduced in high background illumination conditions. Measurements show that the presented setup allows a distance measurement range of up to ∼90 meters to a target of brushed gray concrete in bright sunlight conditions (60 – 70 klux) with 5600 laser pulses sent and only activating a sub-array of 3 × 3 SPADs and 10 TDCs in the receiver. The measurement precision (σ-value) is in the millimeter range.
- Open Access
- 14 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-12
A 35 MHz CMOS Receiver for 3 ns Laser Pulses in Pulsed TOF Laser Ranging
The relation between laser transmitter pulse properties and the corresponding optical receiver parameters is discussed, especially from the signal-to-noise ratio and precision points of view. It is shown that the matching of the receiver bandwidth to the laser pulse width maximizes the signal-to-noise ratio without significantly impairing the precision of the measurement. A CMOS receiver with a bandwidth of 35 MHz for the detection of 3 ns (FWHM) laser pulses is presented as a design case. This consists of fully differential pre- and post-amplifiers, biasing circuits and a Gm-RC block to control the output dc levels. The receiver achieves an equivalent total input-referred current noise of 16.5 nArms for 3 ns (FWHM) laser pulses with an 80 μm (diameter) avalanche photo detector (1550 nm). The single shot measurement precision (σ - value) is ~200 ps at an SNR of 20. The receiver is realized in 0.18 μm CMOS technology and consumes 90 mW of power.
- 14 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-12
Open AccessA 35 MHz CMOS Receiver for 3 ns Laser Pulses in Pulsed TOF Laser Ranging
The relation between laser transmitter pulse properties and the corresponding optical receiver parameters is discussed, especially from the signal-to-noise ratio and precision points of view. It is shown that the matching of the receiver bandwidth to the laser pulse width maximizes the signal-to-noise ratio without significantly impairing the precision of the measurement. A CMOS receiver with a bandwidth of 35 MHz for the detection of 3 ns (FWHM) laser pulses is presented as a design case. This consists of fully differential pre- and post-amplifiers, biasing circuits and a Gm-RC block to control the output dc levels. The receiver achieves an equivalent total input-referred current noise of 16.5 nArms for 3 ns (FWHM) laser pulses with an 80 μm (diameter) avalanche photo detector (1550 nm). The single shot measurement precision (σ - value) is ~200 ps at an SNR of 20. The receiver is realized in 0.18 μm CMOS technology and consumes 90 mW of power.
- Open Access
- 14 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 16 (2) , 1-7
3-D Range Imaging Using Stripe-Like Illumination and SPAD-Based Pulsed TOF Techniques
A solid-state three-dimensional (3-D) range imager using the pulsed time-of-flight principle and a single photon avalanche diode (SPAD) based receiver is demonstrated. Contrary to conventional flood illumination, the suggested system uses sequentially scanned illumination stripes to increase the irradiance under the measured field of view and to reduce the receiver complexity. At equal average illumination power levels this approach increases the signal-to-noise ratio in the receiver enabling thus longer range and/or better performance in high background illumination conditions, albeit at the cost of lower transversal resolution. The transmitter uses eight sequentially driven laser diodes, each of which produces an optical pulse power, length and wavelength of ∼50 W, 2 ns and 905 nm, respectively at a pulse rate of ∼30 kHz so that the total effective pulsing rate is ∼250 kHz and the average illumination power is ∼30 mW. 3-D imaging is demonstrated outdoors in over 50 klux ambient lighting up to ∼10 m distance with 15 Hz frame rate and mm–cm level longitudinal precision in a field of view of about 40×10 degrees. The transversal resolution of the system is 16×128 pixels. The measurement results show 3-D measurement precision scaling according to the laser pulse width and averaging.
- 14 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 16 (2) , 1-7
Open Access3-D Range Imaging Using Stripe-Like Illumination and SPAD-Based Pulsed TOF Techniques
A solid-state three-dimensional (3-D) range imager using the pulsed time-of-flight principle and a single photon avalanche diode (SPAD) based receiver is demonstrated. Contrary to conventional flood illumination, the suggested system uses sequentially scanned illumination stripes to increase the irradiance under the measured field of view and to reduce the receiver complexity. At equal average illumination power levels this approach increases the signal-to-noise ratio in the receiver enabling thus longer range and/or better performance in high background illumination conditions, albeit at the cost of lower transversal resolution. The transmitter uses eight sequentially driven laser diodes, each of which produces an optical pulse power, length and wavelength of ∼50 W, 2 ns and 905 nm, respectively at a pulse rate of ∼30 kHz so that the total effective pulsing rate is ∼250 kHz and the average illumination power is ∼30 mW. 3-D imaging is demonstrated outdoors in over 50 klux ambient lighting up to ∼10 m distance with 15 Hz frame rate and mm–cm level longitudinal precision in a field of view of about 40×10 degrees. The transversal resolution of the system is 16×128 pixels. The measurement results show 3-D measurement precision scaling according to the laser pulse width and averaging.
- Open Access
- 24 February 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 14 (2) , 1-11
Solid-State Pulsed Time-of-Flight 3-D Range Imaging Using CMOS SPAD Focal Plane Array Receiver and Block-Based Illumination Techniques
Full realization of a solid-state 3-D range imager based on the pulsed time-of-flight method is presented. The system uses block-based segmented illumination in the transmitter realized with a 16-element common anode laser diode bar. The receiver is based on a single chip 2-D SPAD/TDC 0.35 μm CMOS array with 32 × 128 SPAD pixels and 257 TDCs. Segmentation of the illumination improves the SN BG R in the detection and results in simpler receiver realization than in the commonly used flood-illumination approach. The system is capable of producing cm-accurate 3-D range images within a FOV of 40° × 10° up to a range of 15 m in normal office lighting at a frame rate of ∼30 fps using a low average illumination power of only 2.6 mW. In background illumination of ∼20 klux, 3-D range images were captured at a distance of ∼13 m using the gated SPAD approach at a frame rate of ∼1 fps.
- 24 February 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 14 (2) , 1-11
Open AccessSolid-State Pulsed Time-of-Flight 3-D Range Imaging Using CMOS SPAD Focal Plane Array Receiver and Block-Based Illumination Techniques
Full realization of a solid-state 3-D range imager based on the pulsed time-of-flight method is presented. The system uses block-based segmented illumination in the transmitter realized with a 16-element common anode laser diode bar. The receiver is based on a single chip 2-D SPAD/TDC 0.35 μm CMOS array with 32 × 128 SPAD pixels and 257 TDCs. Segmentation of the illumination improves the SN BG R in the detection and results in simpler receiver realization than in the commonly used flood-illumination approach. The system is capable of producing cm-accurate 3-D range images within a FOV of 40° × 10° up to a range of 15 m in normal office lighting at a frame rate of ∼30 fps using a low average illumination power of only 2.6 mW. In background illumination of ∼20 klux, 3-D range images were captured at a distance of ∼13 m using the gated SPAD approach at a frame rate of ∼1 fps.
- Open Access
- 17 August 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 21 (20) , 22944-22955
A Low-Noise and Wide Dynamic Range 15 MHz CMOS Receiver for Pulsed Time-of-Flight Laser Ranging
A laser radar receiver channel targeted at pulsed time-of-flight laser radar applications using 5ns…20ns laser pulses at the 1550nm wavelength region has been designed. The receiver includes a transimpedance preamplifier, post-amplifiers and analog output buffer and has a bandwidth of 15MHz and input reduced total equivalent current noise of ~3nArms without the contribution of the APD noise. The receiver supports both the single shot and transient recording operation modes. By utilizing the time domain compensation methods, the single shot timing walk is at the level of +/−100ps within a wide dynamic range of 1: 36 000 of the received echo amplitudes. It is demonstrated that the designed receiver allows the pulsed time-of-flight measurement in the single shot mode to non-cooperative targets up to distances of several hundreds of meters with a laser pulse power of 4 W and receiver aperture of 20mm.
- 17 August 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 21 (20) , 22944-22955
Open AccessA Low-Noise and Wide Dynamic Range 15 MHz CMOS Receiver for Pulsed Time-of-Flight Laser Ranging
A laser radar receiver channel targeted at pulsed time-of-flight laser radar applications using 5ns…20ns laser pulses at the 1550nm wavelength region has been designed. The receiver includes a transimpedance preamplifier, post-amplifiers and analog output buffer and has a bandwidth of 15MHz and input reduced total equivalent current noise of ~3nArms without the contribution of the APD noise. The receiver supports both the single shot and transient recording operation modes. By utilizing the time domain compensation methods, the single shot timing walk is at the level of +/−100ps within a wide dynamic range of 1: 36 000 of the received echo amplitudes. It is demonstrated that the designed receiver allows the pulsed time-of-flight measurement in the single shot mode to non-cooperative targets up to distances of several hundreds of meters with a laser pulse power of 4 W and receiver aperture of 20mm.
- 10 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 21 (15) , 17200-17206
Fusion of 4D Point Clouds From a 2D Profilometer and a 3D Lidar on an Excavator
The research aimed to integrate a solid-state 2D-pulsed time-of-flight (TOF) flash Lidar profilometer and a mechanically scanning 3D Lidar in order to monitor the 4D (3D + signal intensity) environment at a construction site from an excavator. Utilizing the excavator’s GNSS and IMU sensor data enables to fuse the profilometer and 3D Lidar point clouds into the same coordinate system. Both measurement devices have quite a narrow field of view, but the overall viewing angle is expanded due to the movement of the excavator boom and rotation of the excavator cab. The major advantage of this combination method is that the profilometer provides centimetre-accurate details of the worksite within a range of approximately 1–10 m, while the commercial 3D Lidar scanner provides a larger scale (roughly 1–64 m) description of the worksite with an accuracy of ±6 cm. Additionally, the profilometer’s intensity information can be used to identify people on the basis of varying reflective vest patterns. The experimental results indicate that our combination system can accurately build a quality 4D point cloud map better than either individual device on its own. The combination of Lidars could prove to be an interesting tool, with the potential to improve construction site management processes.
- 10 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 21 (15) , 17200-17206
Fusion of 4D Point Clouds From a 2D Profilometer and a 3D Lidar on an Excavator
The research aimed to integrate a solid-state 2D-pulsed time-of-flight (TOF) flash Lidar profilometer and a mechanically scanning 3D Lidar in order to monitor the 4D (3D + signal intensity) environment at a construction site from an excavator. Utilizing the excavator’s GNSS and IMU sensor data enables to fuse the profilometer and 3D Lidar point clouds into the same coordinate system. Both measurement devices have quite a narrow field of view, but the overall viewing angle is expanded due to the movement of the excavator boom and rotation of the excavator cab. The major advantage of this combination method is that the profilometer provides centimetre-accurate details of the worksite within a range of approximately 1–10 m, while the commercial 3D Lidar scanner provides a larger scale (roughly 1–64 m) description of the worksite with an accuracy of ±6 cm. Additionally, the profilometer’s intensity information can be used to identify people on the basis of varying reflective vest patterns. The experimental results indicate that our combination system can accurately build a quality 4D point cloud map better than either individual device on its own. The combination of Lidars could prove to be an interesting tool, with the potential to improve construction site management processes.
- Open Access
- 1 May 2021
- Published by SPIE-Intl Soc Optical Eng in Optical Engineering
- Vol. 60 (05) , 054105-11
Solid-state block-based pulsed laser illuminator for single-photon avalanche diode detection-based time-of-flight 3D range imaging
3D range imaging has traditionally been used in surveying, civil engineering, inspection, and quality control,1,2 but there has been a growing interest in exploiting these techniques in a wider field of applications, e.g., for environment sensing in autonomous cars. Other relevant applications could be robotics, security, small vehicle guidance, e.g., Unmanned Aerial Vehicles, virtual reality/augmented reality, consumer electronics (games), and man-machine interfaces, e.g., gesture control.3 – 5
- 1 May 2021
- Published by SPIE-Intl Soc Optical Eng in Optical Engineering
- Vol. 60 (05) , 054105-11
Open AccessSolid-state block-based pulsed laser illuminator for single-photon avalanche diode detection-based time-of-flight 3D range imaging
3D range imaging has traditionally been used in surveying, civil engineering, inspection, and quality control,1,2 but there has been a growing interest in exploiting these techniques in a wider field of applications, e.g., for environment sensing in autonomous cars. Other relevant applications could be robotics, security, small vehicle guidance, e.g., Unmanned Aerial Vehicles, virtual reality/augmented reality, consumer electronics (games), and man-machine interfaces, e.g., gesture control.3 – 5
- 1 January 2021
- Published by Elsevier in Automation in Construction
- Vol. 121, 103429
Time-of-flight sensor for getting shape model of automobiles toward digital 3D imaging approach of autonomous driving
- 1 January 2021
- Published by Elsevier in Automation in Construction
- Vol. 121, 103429
Time-of-flight sensor for getting shape model of automobiles toward digital 3D imaging approach of autonomous driving
- Open Access
Temporal and Spatial Focusing in SPAD-Based Solid-State Pulsed Time-of-Flight Laser Range Imaging
The relation between signal and background noise strengths in single-photon avalanche diode (SPAD)-based pulsed time-of-flight 3-D range imaging is analyzed on the assumption that the SPAD detector is operating in the single photon detection mode. Several practical measurement cases using a 256-pixel solid-state pulsed time-of-flight (TOF) line profiler are presented and analyzed in the light of the resulting analysis. It is shown that in this case it is advantageous to concentrate the available optical average power in short, intensive pulses and to focus the optical energy in spatial terms. In 3-D range imaging, this could be achieved by using block-based illumination instead of the regularly used flood illumination. One modification of this approach could be a source that would illuminate the system FOV only in narrow laser stripes. It is shown that a 256-pixel SPAD-based pulsed TOF line profiler following these design principles can achieve a measurement range of 5–10 m to non-cooperative targets at a rate of ~10 lines/s under bright sunlight conditions using an average optical power of only 260 µW.
Open AccessTemporal and Spatial Focusing in SPAD-Based Solid-State Pulsed Time-of-Flight Laser Range Imaging
The relation between signal and background noise strengths in single-photon avalanche diode (SPAD)-based pulsed time-of-flight 3-D range imaging is analyzed on the assumption that the SPAD detector is operating in the single photon detection mode. Several practical measurement cases using a 256-pixel solid-state pulsed time-of-flight (TOF) line profiler are presented and analyzed in the light of the resulting analysis. It is shown that in this case it is advantageous to concentrate the available optical average power in short, intensive pulses and to focus the optical energy in spatial terms. In 3-D range imaging, this could be achieved by using block-based illumination instead of the regularly used flood illumination. One modification of this approach could be a source that would illuminate the system FOV only in narrow laser stripes. It is shown that a 256-pixel SPAD-based pulsed TOF line profiler following these design principles can achieve a measurement range of 5–10 m to non-cooperative targets at a rate of ~10 lines/s under bright sunlight conditions using an average optical power of only 260 µW.
- Open Access
- 14 October 2020
- Published by SPIE-Intl Soc Optical Eng in Optical Engineering
- Vol. 59 (10) , 1-16
High-speed wide dynamic range linear mode time-of-flight receiver based on zero-crossing timing detection
We present an accurate laser radar receiver with a wide dynamic range intended for ranging applications based on an event-based approach, in which a receiver-time-to-digital converter is used to extract the timing information from the reflected echo. The receiver is based on LC resonance pulse shaping at the input so that the unipolar pulse detected by the avalanche photodiode is converted to a bipolar signal, and the first zero-crossing of this converted signal is marked as the only timing point. One important aspect of the proposed scheme is that it does not need any postcompensation or gain control for achieving a wide dynamic range. The receiver chip was fabricated in a 0.35-μm standard CMOS technology, and a laser radar platform was developed to verify the functionality of the proposed receiver channel. The measured accuracy of the receiver is ±3.5 cm within a dynamic range of more than 1:250,000 using 3-ns FWHM pulses when target materials with different reflectivities are used in the measurements. The single-shot precision of the receiver (σ value) is ∼5 cm for a minimum SNR of ∼10.
- 14 October 2020
- Published by SPIE-Intl Soc Optical Eng in Optical Engineering
- Vol. 59 (10) , 1-16
Open AccessHigh-speed wide dynamic range linear mode time-of-flight receiver based on zero-crossing timing detection
We present an accurate laser radar receiver with a wide dynamic range intended for ranging applications based on an event-based approach, in which a receiver-time-to-digital converter is used to extract the timing information from the reflected echo. The receiver is based on LC resonance pulse shaping at the input so that the unipolar pulse detected by the avalanche photodiode is converted to a bipolar signal, and the first zero-crossing of this converted signal is marked as the only timing point. One important aspect of the proposed scheme is that it does not need any postcompensation or gain control for achieving a wide dynamic range. The receiver chip was fabricated in a 0.35-μm standard CMOS technology, and a laser radar platform was developed to verify the functionality of the proposed receiver channel. The measured accuracy of the receiver is ±3.5 cm within a dynamic range of more than 1:250,000 using 3-ns FWHM pulses when target materials with different reflectivities are used in the measurements. The single-shot precision of the receiver (σ value) is ∼5 cm for a minimum SNR of ∼10.