Sahba Jahromi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Sahba Jahromi has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Juha Kostamovaara
Circuits and Systems Research Unit, UNIVERSITY OF OULU, Oulu, Finland
6 shared publications - Jussi-Pekka Jansson
Circuits and Systems Research Unit, UNIVERSITY OF OULU, Oulu, Finland
5 shared publications - Pekka Keranen
Circuits and Systems Research Unit, UNIVERSITY OF OULU, Oulu, Finland
4 shared publications - Lauri Hallman
Univ. of Oulu (Finland)
3 shared publications - Guoyong Duan
University of Oulu, Oulu, Finland
1 shared publication Juha Kostamovaara
University of Oulu, Faculty of Information Technology and Electrical Engineering, Circuits and Systems (CAS) Research Unit Oulu, Finland
1 shared publication
Latest Publications
- Open Access
- 14 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 16 (2) , 1-7
3-D Range Imaging Using Stripe-Like Illumination and SPAD-Based Pulsed TOF Techniques
A solid-state three-dimensional (3-D) range imager using the pulsed time-of-flight principle and a single photon avalanche diode (SPAD) based receiver is demonstrated. Contrary to conventional flood illumination, the suggested system uses sequentially scanned illumination stripes to increase the irradiance under the measured field of view and to reduce the receiver complexity. At equal average illumination power levels this approach increases the signal-to-noise ratio in the receiver enabling thus longer range and/or better performance in high background illumination conditions, albeit at the cost of lower transversal resolution. The transmitter uses eight sequentially driven laser diodes, each of which produces an optical pulse power, length and wavelength of ∼50 W, 2 ns and 905 nm, respectively at a pulse rate of ∼30 kHz so that the total effective pulsing rate is ∼250 kHz and the average illumination power is ∼30 mW. 3-D imaging is demonstrated outdoors in over 50 klux ambient lighting up to ∼10 m distance with 15 Hz frame rate and mm–cm level longitudinal precision in a field of view of about 40×10 degrees. The transversal resolution of the system is 16×128 pixels. The measurement results show 3-D measurement precision scaling according to the laser pulse width and averaging.
- 14 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 16 (2) , 1-7
Open Access3-D Range Imaging Using Stripe-Like Illumination and SPAD-Based Pulsed TOF Techniques
A solid-state three-dimensional (3-D) range imager using the pulsed time-of-flight principle and a single photon avalanche diode (SPAD) based receiver is demonstrated. Contrary to conventional flood illumination, the suggested system uses sequentially scanned illumination stripes to increase the irradiance under the measured field of view and to reduce the receiver complexity. At equal average illumination power levels this approach increases the signal-to-noise ratio in the receiver enabling thus longer range and/or better performance in high background illumination conditions, albeit at the cost of lower transversal resolution. The transmitter uses eight sequentially driven laser diodes, each of which produces an optical pulse power, length and wavelength of ∼50 W, 2 ns and 905 nm, respectively at a pulse rate of ∼30 kHz so that the total effective pulsing rate is ∼250 kHz and the average illumination power is ∼30 mW. 3-D imaging is demonstrated outdoors in over 50 klux ambient lighting up to ∼10 m distance with 15 Hz frame rate and mm–cm level longitudinal precision in a field of view of about 40×10 degrees. The transversal resolution of the system is 16×128 pixels. The measurement results show 3-D measurement precision scaling according to the laser pulse width and averaging.
- Open Access
- 24 February 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 14 (2) , 1-11
Solid-State Pulsed Time-of-Flight 3-D Range Imaging Using CMOS SPAD Focal Plane Array Receiver and Block-Based Illumination Techniques
Full realization of a solid-state 3-D range imager based on the pulsed time-of-flight method is presented. The system uses block-based segmented illumination in the transmitter realized with a 16-element common anode laser diode bar. The receiver is based on a single chip 2-D SPAD/TDC 0.35 μm CMOS array with 32 × 128 SPAD pixels and 257 TDCs. Segmentation of the illumination improves the SN BG R in the detection and results in simpler receiver realization than in the commonly used flood-illumination approach. The system is capable of producing cm-accurate 3-D range images within a FOV of 40° × 10° up to a range of 15 m in normal office lighting at a frame rate of ∼30 fps using a low average illumination power of only 2.6 mW. In background illumination of ∼20 klux, 3-D range images were captured at a distance of ∼13 m using the gated SPAD approach at a frame rate of ∼1 fps.
- 24 February 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 14 (2) , 1-11
Open AccessSolid-State Pulsed Time-of-Flight 3-D Range Imaging Using CMOS SPAD Focal Plane Array Receiver and Block-Based Illumination Techniques
Full realization of a solid-state 3-D range imager based on the pulsed time-of-flight method is presented. The system uses block-based segmented illumination in the transmitter realized with a 16-element common anode laser diode bar. The receiver is based on a single chip 2-D SPAD/TDC 0.35 μm CMOS array with 32 × 128 SPAD pixels and 257 TDCs. Segmentation of the illumination improves the SN BG R in the detection and results in simpler receiver realization than in the commonly used flood-illumination approach. The system is capable of producing cm-accurate 3-D range images within a FOV of 40° × 10° up to a range of 15 m in normal office lighting at a frame rate of ∼30 fps using a low average illumination power of only 2.6 mW. In background illumination of ∼20 klux, 3-D range images were captured at a distance of ∼13 m using the gated SPAD approach at a frame rate of ∼1 fps.
- Open Access
Temporal and Spatial Focusing in SPAD-Based Solid-State Pulsed Time-of-Flight Laser Range Imaging
The relation between signal and background noise strengths in single-photon avalanche diode (SPAD)-based pulsed time-of-flight 3-D range imaging is analyzed on the assumption that the SPAD detector is operating in the single photon detection mode. Several practical measurement cases using a 256-pixel solid-state pulsed time-of-flight (TOF) line profiler are presented and analyzed in the light of the resulting analysis. It is shown that in this case it is advantageous to concentrate the available optical average power in short, intensive pulses and to focus the optical energy in spatial terms. In 3-D range imaging, this could be achieved by using block-based illumination instead of the regularly used flood illumination. One modification of this approach could be a source that would illuminate the system FOV only in narrow laser stripes. It is shown that a 256-pixel SPAD-based pulsed TOF line profiler following these design principles can achieve a measurement range of 5–10 m to non-cooperative targets at a rate of ~10 lines/s under bright sunlight conditions using an average optical power of only 260 µW.
Open AccessTemporal and Spatial Focusing in SPAD-Based Solid-State Pulsed Time-of-Flight Laser Range Imaging
The relation between signal and background noise strengths in single-photon avalanche diode (SPAD)-based pulsed time-of-flight 3-D range imaging is analyzed on the assumption that the SPAD detector is operating in the single photon detection mode. Several practical measurement cases using a 256-pixel solid-state pulsed time-of-flight (TOF) line profiler are presented and analyzed in the light of the resulting analysis. It is shown that in this case it is advantageous to concentrate the available optical average power in short, intensive pulses and to focus the optical energy in spatial terms. In 3-D range imaging, this could be achieved by using block-based illumination instead of the regularly used flood illumination. One modification of this approach could be a source that would illuminate the system FOV only in narrow laser stripes. It is shown that a 256-pixel SPAD-based pulsed TOF line profiler following these design principles can achieve a measurement range of 5–10 m to non-cooperative targets at a rate of ~10 lines/s under bright sunlight conditions using an average optical power of only 260 µW.
- Open Access
- 13 February 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 55 (7) , 1960-1970
A 32 × 128 SPAD-257 TDC Receiver IC for Pulsed TOF Solid-State 3-D Imaging
A single-chip receiver for pulsed laser direct time-of-flight 3-D imaging applications has been realized in a 0.35-μm HV CMOS technology. The chip includes a 32 x 128 single-photon avalanche diode (SPAD) array [35% fill factor (FF)] and 257 time-to-digital converters (TDCs) with a ~78-ps resolution. Two adjacent rows (2 x 128 SPADs) at a time can be selected for simultaneous measurement, i.e., 16 measurement cycles are needed to cover the whole array. SPADs are capable of operating in a gated mode in order to suppress dark and background light-induced detections. The IC was designed to be used in a solid-state 3-D imaging system with laser illumination concentrated in both time (short sub-ns pulses) and space (targeting only the active rows of the SPAD array). The performance of the receiver IC was characterized in a solid-state 3-D range imager with flood-pulsed illumination from a laser diode (LD)-based transmitter, which produced short [~150-ps full-width at half-maximum (FWHM)] high-energy (~3.8-nJ pulse/~14-W peak power) pulses at a pulsing rate of 250 kHz when operating at a wavelength of 810 nm. Two detector/TDC ICs formed an 8k pixel receiver, targeting a field-of-view of ~42° x 21° by means of simple optics. Frame rates of up to 20 fps were demonstrated with a centimeter-level precision in the case of Lambertian targets within a range of 3.5 m.
- 13 February 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 55 (7) , 1960-1970
Open AccessA 32 × 128 SPAD-257 TDC Receiver IC for Pulsed TOF Solid-State 3-D Imaging
A single-chip receiver for pulsed laser direct time-of-flight 3-D imaging applications has been realized in a 0.35-μm HV CMOS technology. The chip includes a 32 x 128 single-photon avalanche diode (SPAD) array [35% fill factor (FF)] and 257 time-to-digital converters (TDCs) with a ~78-ps resolution. Two adjacent rows (2 x 128 SPADs) at a time can be selected for simultaneous measurement, i.e., 16 measurement cycles are needed to cover the whole array. SPADs are capable of operating in a gated mode in order to suppress dark and background light-induced detections. The IC was designed to be used in a solid-state 3-D imaging system with laser illumination concentrated in both time (short sub-ns pulses) and space (targeting only the active rows of the SPAD array). The performance of the receiver IC was characterized in a solid-state 3-D range imager with flood-pulsed illumination from a laser diode (LD)-based transmitter, which produced short [~150-ps full-width at half-maximum (FWHM)] high-energy (~3.8-nJ pulse/~14-W peak power) pulses at a pulsing rate of 250 kHz when operating at a wavelength of 810 nm. Two detector/TDC ICs formed an 8k pixel receiver, targeting a field-of-view of ~42° x 21° by means of simple optics. Frame rates of up to 20 fps were demonstrated with a centimeter-level precision in the case of Lambertian targets within a range of 3.5 m.
- Open Access
- 6 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 69 (6) , 3928-3935
Enhancing Nutt-Based Time-to-Digital Converter Performance With Internal Systematic Averaging
A time-to-digital converter (TDC) often consists of sophisticated, multilevel, subgate delay structures, when time intervals need to be measured precisely. The resolution improvement is rewarding until integral nonlinearity (INL) and random jitter begins to limit the measurement performance. INL can then be minimized with calibration techniques and result postprocessing. The TDC architecture based on a counter and timing signal interpolation (the Nutt method) makes it possible to measure long time intervals precisely. It also offers an effective means of improving precision by averaging. Traditional averaging, however, demands several successive measurements, which increases the measurement time and power consumption. It is shown here that by using several interpolators that are sampled homogeneously over the clock period, the effects of limited resolution, interpolation nonlinearities, and random noise can be markedly reduced. The designed CMOS TDC utilizing internal systematic sampling technique achieves 3.0-ps root mean square (RMS) single-shot precision without any additional calibration or nonlinearity correction.
- 6 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 69 (6) , 3928-3935
Open AccessEnhancing Nutt-Based Time-to-Digital Converter Performance With Internal Systematic Averaging
A time-to-digital converter (TDC) often consists of sophisticated, multilevel, subgate delay structures, when time intervals need to be measured precisely. The resolution improvement is rewarding until integral nonlinearity (INL) and random jitter begins to limit the measurement performance. INL can then be minimized with calibration techniques and result postprocessing. The TDC architecture based on a counter and timing signal interpolation (the Nutt method) makes it possible to measure long time intervals precisely. It also offers an effective means of improving precision by averaging. Traditional averaging, however, demands several successive measurements, which increases the measurement time and power consumption. It is shown here that by using several interpolators that are sampled homogeneously over the clock period, the effects of limited resolution, interpolation nonlinearities, and random noise can be markedly reduced. The designed CMOS TDC utilizing internal systematic sampling technique achieves 3.0-ps root mean square (RMS) single-shot precision without any additional calibration or nonlinearity correction.
- 27 July 2018
- Published by Optica Publishing Group in Optics Express
- Vol. 26 (16) , 20622-20632
Timing and probability of crosstalk in a dense CMOS SPAD array in pulsed TOF applications
As the distance between neighboring devices in large CMOS single-photon avalanche diode (SPAD) arrays is reduced for improving the density, increased crosstalk becomes an important issue, limiting the maximum practical fill factor of the array. In this study, the temporal correlation of crosstalk events, as well as the crosstalk probability, and their dependence on parameters, such as the illumination wavelength and intensity, and the distance between SPADs, are investigated via measurement of a ~45%-fill factor CMOS SPAD array fabricated using 0.35-µm high-voltage CMOS technology. The SPADs have 24 µm × 24 µm square-shaped active areas, and all devices share a common deep-N-well cathode. On-chip time-to-digital converters with 65-ps resolution are used to measure the timing of crosstalk events in “coincidence measurements.” For the crosstalk measurements, the internal noise in one SPAD is used to produce crosstalk events in the neighboring devices. The measurement results indicate both optical and electrical crosstalk with the crosstalk events, having a specific temporal distribution. The crosstalk probability in the first two adjacent pixels is found to be 0.3% and 0.01%, with a distribution having full widths at half maximum (FWHMs) of 700 and 400 ps, respectively. In pulsed time-of-flight measurements, when one SPAD is triggered with external short-pulsed (FWHM of approximately 200 ps) illumination, extra correlated noise in the adjacent SPADs added to the crosstalk noise, increasing the correlated noise considerably. This additional noise was a secondary effect of the absorbed laser photons deep in the substrate.
- 27 July 2018
- Published by Optica Publishing Group in Optics Express
- Vol. 26 (16) , 20622-20632
Timing and probability of crosstalk in a dense CMOS SPAD array in pulsed TOF applications
As the distance between neighboring devices in large CMOS single-photon avalanche diode (SPAD) arrays is reduced for improving the density, increased crosstalk becomes an important issue, limiting the maximum practical fill factor of the array. In this study, the temporal correlation of crosstalk events, as well as the crosstalk probability, and their dependence on parameters, such as the illumination wavelength and intensity, and the distance between SPADs, are investigated via measurement of a ~45%-fill factor CMOS SPAD array fabricated using 0.35-µm high-voltage CMOS technology. The SPADs have 24 µm × 24 µm square-shaped active areas, and all devices share a common deep-N-well cathode. On-chip time-to-digital converters with 65-ps resolution are used to measure the timing of crosstalk events in “coincidence measurements.” For the crosstalk measurements, the internal noise in one SPAD is used to produce crosstalk events in the neighboring devices. The measurement results indicate both optical and electrical crosstalk with the crosstalk events, having a specific temporal distribution. The crosstalk probability in the first two adjacent pixels is found to be 0.3% and 0.01%, with a distribution having full widths at half maximum (FWHMs) of 700 and 400 ps, respectively. In pulsed time-of-flight measurements, when one SPAD is triggered with external short-pulsed (FWHM of approximately 200 ps) illumination, extra correlated noise in the adjacent SPADs added to the crosstalk noise, increasing the correlated noise considerably. This additional noise was a secondary effect of the absorbed laser photons deep in the substrate.
- Open Access
- 26 March 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 10 (4) , 1-12
On Two-Dimensional Rangefinding Using a ∼1 nJ/∼100 ps Laser Diode Transmitter and a CMOS SPAD Matrix
A potentially compact 2-D range profiler for non-cooperative targets with a distance range of >10 m is demonstrated. A laser diode utilizing enhanced gain switching is used as a transmitter to provide short, high energy optical pulses (~1 nJ/140 ps). Cylindrical lenses spread the laser beam in one dimension and collimate the beam in the other dimension to illuminate a line shaped field of view of about 45°. A similarly shaped field of view for the detector is realized with a single-photon avalanche diode (SPAD) detector matrix. Compared to a flash 3-D rangefinder, the 2-D rangefinding scheme relaxes the SPAD and time-to-digital converter (TDC) design requirements, increases the signal irradiance at the detector, can have better tolerance for background illumination, and it can be sufficient or advantageous in some applications. The distance measurement precision to each direction is inherently within a few centimeters (FWHM) since the laser pulse width and SPAD detector jitter both correspond with an optical pulse back-and-forth flight time of about a centimeter. Demonstration measurements show >15 Hz line rate and a lateral resolution of about 5 mrad to non-cooperative targets at distances of more than 10 m.
- 26 March 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Journal
- Vol. 10 (4) , 1-12
Open AccessOn Two-Dimensional Rangefinding Using a ∼1 nJ/∼100 ps Laser Diode Transmitter and a CMOS SPAD Matrix
A potentially compact 2-D range profiler for non-cooperative targets with a distance range of >10 m is demonstrated. A laser diode utilizing enhanced gain switching is used as a transmitter to provide short, high energy optical pulses (~1 nJ/140 ps). Cylindrical lenses spread the laser beam in one dimension and collimate the beam in the other dimension to illuminate a line shaped field of view of about 45°. A similarly shaped field of view for the detector is realized with a single-photon avalanche diode (SPAD) detector matrix. Compared to a flash 3-D rangefinder, the 2-D rangefinding scheme relaxes the SPAD and time-to-digital converter (TDC) design requirements, increases the signal irradiance at the detector, can have better tolerance for background illumination, and it can be sufficient or advantageous in some applications. The distance measurement precision to each direction is inherently within a few centimeters (FWHM) since the laser pulse width and SPAD detector jitter both correspond with an optical pulse back-and-forth flight time of about a centimeter. Demonstration measurements show >15 Hz line rate and a lateral resolution of about 5 mrad to non-cooperative targets at distances of more than 10 m.