Jordi Freixa
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Jordi Freixa has a total of 120 co-authors. Here are the top co-authors by number of shared publications:
- Victor Martinez-Quiroga
Innovative Systems Software, Idaho Falls, ID
8 shared publications F. Reventós
6 shared publicationsF. Reventos
4 shared publicationsFrancesc Reventós
4 shared publications- Lluis Batet
Departament de Física, Universitat Politècnica de Catalunya, Barcelona, Spain
4 shared publications A. Manera
3 shared publications
Latest Publications
- Open Access
- 21 October 2026
- Published by Elsevier in SSRN Electronic Journal
Assessment of Reflood Predictions and Physical-Model Sensitivities Using RBHT Experiments
The predictive capabilities of the RELAP5/MOD3.3 code to reproduce fuel bundle reflooding have been assessed through the simulation and sensitivity analysis of the complete set of open-phase experiments within the RBHT-II project. The experimental set comprised 11 reflood tests with varying bundle powers and flooding rates. Spearman rank associations under simultaneous variation of 20 multipliers were examined alongside one-at-a-time (OAT) responses for selected multipliers. Baseline relative errors ranged from -8.09% to 3.66% for peak cladding temperature (PCT) and from -36.70% to -10.87% for quench time. The calculated quench front reached the reference elevation earlier than in the experiment in every test. Temperature histories revealed cooling-response differences across test conditions and measurement locations, complementing the scalar assessments. For groups defined by relative power and flooding rate within the test set, PCT showed the strongest rank associations with the vapor-side heat-transfer multiplier for saturated film boiling in the High group and the heat-transfer multiplier for single-phase vapor convection in the Medium and Low groups. These multipliers scale vapor-side heat transfer in saturated film boiling and single-phase vapor convection, respectively. For the time of quench, the liquid-side heat transfer coefficient under saturated film boiling was the dominant parameter for the High and Medium groups. In the Low group, the heat-transfer multiplier for single-phase vapor convection or the vapor-liquid interfacial-drag multiplier slgdrag ranked first depending on the test. OAT analysis revealed within-group response differences and complemented rank associations with individual response spans. These combined assessments provide condition- and response-specific priorities for examining physical models in subsequent best-estimate plus uncertainty (BEPU) analyses.
- 21 October 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessAssessment of Reflood Predictions and Physical-Model Sensitivities Using RBHT Experiments
The predictive capabilities of the RELAP5/MOD3.3 code to reproduce fuel bundle reflooding have been assessed through the simulation and sensitivity analysis of the complete set of open-phase experiments within the RBHT-II project. The experimental set comprised 11 reflood tests with varying bundle powers and flooding rates. Spearman rank associations under simultaneous variation of 20 multipliers were examined alongside one-at-a-time (OAT) responses for selected multipliers. Baseline relative errors ranged from -8.09% to 3.66% for peak cladding temperature (PCT) and from -36.70% to -10.87% for quench time. The calculated quench front reached the reference elevation earlier than in the experiment in every test. Temperature histories revealed cooling-response differences across test conditions and measurement locations, complementing the scalar assessments. For groups defined by relative power and flooding rate within the test set, PCT showed the strongest rank associations with the vapor-side heat-transfer multiplier for saturated film boiling in the High group and the heat-transfer multiplier for single-phase vapor convection in the Medium and Low groups. These multipliers scale vapor-side heat transfer in saturated film boiling and single-phase vapor convection, respectively. For the time of quench, the liquid-side heat transfer coefficient under saturated film boiling was the dominant parameter for the High and Medium groups. In the Low group, the heat-transfer multiplier for single-phase vapor convection or the vapor-liquid interfacial-drag multiplier slgdrag ranked first depending on the test. OAT analysis revealed within-group response differences and complemented rank associations with individual response spans. These combined assessments provide condition- and response-specific priorities for examining physical models in subsequent best-estimate plus uncertainty (BEPU) analyses.
- Open Access
- 28 April 2026
- Published by Elsevier in SSRN Electronic Journal
Inverse Uncertainty Quantification of RELAP’s Post Critical Heat Flux Behavior
Best Estimate Plus Uncertainty (BEPU) methodologies are gradually establishing themselves as the favored way to perform Deterministic Safety Assessments of Nuclear Power Plants, because they account for uncertainties in plant states and physical behaviors while employing accurate-to-reality (best estimate) simulation codes. This work is performed in the context of the ATRIUM project, which seeks to establish best practices and standardize the BEPU process to make the results more consistent, minimizing user effect. The approach taken in this project is to focus on specific phenomenology that is crucial to the progression of the desired transient (a Loss of Coolant Accident), and work with Separate Effect Test experiments to find adequate uncertain parameters and their probability density function, to be forward propagated through BEPU methods.In this article, the specific target phenomenology is the post-critical heat flux heat transfer mechanism, more precisely film boiling heat transfer. Within ATRIUM, three experiment programs were proposed to evaluate the target phenomena: Becker, Stewart, and THTF. Firstly, the adequacy of the different experiments was evaluated along with preliminary RELAP5 simulations. The analysis highlighted the difficulties to reproduce some of the experiments and a final subset of tests was selected for inverse uncertainty quantification.Afterwards, a thorough sensitivity analysis was performed on the physical parameters that may influence the target phenomena, which helped identify the most influential parameters that are sufficient to minimize the error with the experiment. A novel IUQ methodology was then applied to these uncertain parameters and validated through BEPU analyses.
- 28 April 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessInverse Uncertainty Quantification of RELAP’s Post Critical Heat Flux Behavior
Best Estimate Plus Uncertainty (BEPU) methodologies are gradually establishing themselves as the favored way to perform Deterministic Safety Assessments of Nuclear Power Plants, because they account for uncertainties in plant states and physical behaviors while employing accurate-to-reality (best estimate) simulation codes. This work is performed in the context of the ATRIUM project, which seeks to establish best practices and standardize the BEPU process to make the results more consistent, minimizing user effect. The approach taken in this project is to focus on specific phenomenology that is crucial to the progression of the desired transient (a Loss of Coolant Accident), and work with Separate Effect Test experiments to find adequate uncertain parameters and their probability density function, to be forward propagated through BEPU methods.In this article, the specific target phenomenology is the post-critical heat flux heat transfer mechanism, more precisely film boiling heat transfer. Within ATRIUM, three experiment programs were proposed to evaluate the target phenomena: Becker, Stewart, and THTF. Firstly, the adequacy of the different experiments was evaluated along with preliminary RELAP5 simulations. The analysis highlighted the difficulties to reproduce some of the experiments and a final subset of tests was selected for inverse uncertainty quantification.Afterwards, a thorough sensitivity analysis was performed on the physical parameters that may influence the target phenomena, which helped identify the most influential parameters that are sufficient to minimize the error with the experiment. A novel IUQ methodology was then applied to these uncertain parameters and validated through BEPU analyses.
- Open Access
- 12 February 2025
- Published by Elsevier in Annals of Nuclear Energy
- Vol. 215
Core-wide multi-physics simulation of fuel behaviour during large-break LOCA using NEXUS
- 12 February 2025
- Published by Elsevier in Annals of Nuclear Energy
- Vol. 215
Open AccessCore-wide multi-physics simulation of fuel behaviour during large-break LOCA using NEXUS
- 24 October 2024
- Published by Taylor & Francis in Nuclear Technology
- p. 1-18
Assessment of the Choked Flow Model of RELAP5 for Application of Inverse Quantification Methods
- 24 October 2024
- Published by Taylor & Francis in Nuclear Technology
- p. 1-18
Assessment of the Choked Flow Model of RELAP5 for Application of Inverse Quantification Methods
- Open Access
- 14 July 2024
- Published by Elsevier in Nuclear Engineering and Design
- Vol. 427
Application of the ANT assessment methodology for validating LOCUST 1.2 thermal-hydraulic code
- 14 July 2024
- Published by Elsevier in Nuclear Engineering and Design
- Vol. 427
Open AccessApplication of the ANT assessment methodology for validating LOCUST 1.2 thermal-hydraulic code
- 18 June 2024
- Published by Elsevier in Nuclear Engineering and Design
- Vol. 426
Scaling in nuclear thermal hydraulics: Advances, applications and future perspectives in Spain
- 18 June 2024
- Published by Elsevier in Nuclear Engineering and Design
- Vol. 426
Scaling in nuclear thermal hydraulics: Advances, applications and future perspectives in Spain
- 4 January 2024
- Published by Elsevier in Nuclear Engineering and Design
- Vol. 418
Full scope scaling analysis and recommendations for PWR SGTR scenarios
- 4 January 2024
- Published by Elsevier in Nuclear Engineering and Design
- Vol. 418
Full scope scaling analysis and recommendations for PWR SGTR scenarios
- 22 December 2023
- Published by Elsevier in Nuclear Engineering and Design
- Vol. 417
Spanish contribution to the development and application of best estimate plus uncertainty methodologies: Past, present and future
- 22 December 2023
- Published by Elsevier in Nuclear Engineering and Design
- Vol. 417
Spanish contribution to the development and application of best estimate plus uncertainty methodologies: Past, present and future
- Open Access
- 19 January 2023
- Published by Elsevier in Nuclear Engineering and Design
- Vol. 404
Kv-scaling in thermal hydraulics: Background, applications and forthcoming uses
- 19 January 2023
- Published by Elsevier in Nuclear Engineering and Design
- Vol. 404
Open AccessKv-scaling in thermal hydraulics: Background, applications and forthcoming uses