Ioannis Anastasopoulos
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Ioannis Anastasopoulos has a total of 143 co-authors. Here are the top co-authors by number of shared publications:
G. Gazetas
23 shared publications- George Gazetas
National Technical University of Athens
18 shared publications R. Kourkoulis
13 shared publications- Nikos Gerolymos
National Technical University of Athens
12 shared publications F. Gelagoti
Postdoctoral Researcher, School of Civil Engineering, National Technical Univ. of Athens, Athens 10682, Greece
11 shared publicationsGeorge Gazetas
11 shared publications
Latest Publications
- 3 November 2026
- Published by Emerald Publishing in International Journal of Physical Modelling in Geotechnics
- p. 1-19
Scour effects on an unconventional bridge foundation
Reliable prediction of scour at bridge piers supported by shallow foundations of unusual geometry remains challenging using conventional empirical formulations, particularly in confined river sections where foundation–flow interaction is significant. Inspired by an existing historic bridge with a non-standard shallow foundation, this study investigates scour in the presence of buttressed and unbuttressed retaining walls, originally conceived for slope stabilisation rather than scour protection. A series of 1 g physical model tests is conducted under steady, near clear-water flow conditions. Three configurations are comparatively assessed: (a) a single foundation with an unbuttressed retaining wall; (b) the same foundation with a buttressed wall; and (c) two foundations with buttressed walls, reproducing the prototype arrangement. Scour evolution is monitored through time-resolved imaging and high-resolution bed-elevation measurements. The results show that retaining walls modify the approaching flow and promote sediment redistribution, thereby limiting direct foundation exposure. Buttresses further enhance this effect by altering local erosion patterns and delaying scour development at the foundation level. However, when two foundation–wall systems interact within a confined channel, these beneficial mechanisms are partly reduced by mutual interaction effects. The findings clarify geometry-induced scour mechanisms relevant to assessing shallow bridge foundations in confined fluvial environments.
- 3 November 2026
- Published by Emerald Publishing in International Journal of Physical Modelling in Geotechnics
- p. 1-19
Scour effects on an unconventional bridge foundation
Reliable prediction of scour at bridge piers supported by shallow foundations of unusual geometry remains challenging using conventional empirical formulations, particularly in confined river sections where foundation–flow interaction is significant. Inspired by an existing historic bridge with a non-standard shallow foundation, this study investigates scour in the presence of buttressed and unbuttressed retaining walls, originally conceived for slope stabilisation rather than scour protection. A series of 1 g physical model tests is conducted under steady, near clear-water flow conditions. Three configurations are comparatively assessed: (a) a single foundation with an unbuttressed retaining wall; (b) the same foundation with a buttressed wall; and (c) two foundations with buttressed walls, reproducing the prototype arrangement. Scour evolution is monitored through time-resolved imaging and high-resolution bed-elevation measurements. The results show that retaining walls modify the approaching flow and promote sediment redistribution, thereby limiting direct foundation exposure. Buttresses further enhance this effect by altering local erosion patterns and delaying scour development at the foundation level. However, when two foundation–wall systems interact within a confined channel, these beneficial mechanisms are partly reduced by mutual interaction effects. The findings clarify geometry-induced scour mechanisms relevant to assessing shallow bridge foundations in confined fluvial environments.
- Open Access
- 23 July 2026
- Published by Emerald Publishing in International Journal of Physical Modelling in Geotechnics
- p. 1-14
Centrifuge modelling of an offshore monopile in saturated sand under storm loading: WESDOM test programme
A series of centrifuge model tests of an offshore wind turbine (OWT) monopile foundation were conducted using the 500 gtonne capacity beam centrifuge of the ETH Zurich Geotechnical Centrifuge Centre. The paper establishes a meticulous experimental procedure for realistic simulation of OWT monopile foundations subjected to storm loading, revealing soil drainage effects on cyclic monopile response. The model steel monopile, with a ratio of embedded length over diameter, L/D = 3.75, was installed in fully saturated dense Ottawa F-65 sand of target relative density Dr = 75%. The key aspects of the centrifuge modelling campaign, including: (i) construction of the monopile model including internal strain gauges; (ii) air-pluviation of the sand through a custom-built ‘curtain’ raining system; (iii) extensive instrumentation with pore pressure transducers and LVDTs; (v) sand saturation with 60 cp viscous fluid; and (vi) 1 g jacking of the monopile. After spinning up the model to 60 g, the monopile was subjected to lateral one-way sinusoidal and random storm loading using a specially designed hydraulic dynamic actuator that can apply load-controlled time histories in a frequency range of 4–100 Hz in model scale. Selected test results are presented, demonstrating that the experiments successfully captured the partial drainage effects on soil-monopile system response.
- 23 July 2026
- Published by Emerald Publishing in International Journal of Physical Modelling in Geotechnics
- p. 1-14
Open AccessCentrifuge modelling of an offshore monopile in saturated sand under storm loading: WESDOM test programme
A series of centrifuge model tests of an offshore wind turbine (OWT) monopile foundation were conducted using the 500 gtonne capacity beam centrifuge of the ETH Zurich Geotechnical Centrifuge Centre. The paper establishes a meticulous experimental procedure for realistic simulation of OWT monopile foundations subjected to storm loading, revealing soil drainage effects on cyclic monopile response. The model steel monopile, with a ratio of embedded length over diameter, L/D = 3.75, was installed in fully saturated dense Ottawa F-65 sand of target relative density Dr = 75%. The key aspects of the centrifuge modelling campaign, including: (i) construction of the monopile model including internal strain gauges; (ii) air-pluviation of the sand through a custom-built ‘curtain’ raining system; (iii) extensive instrumentation with pore pressure transducers and LVDTs; (v) sand saturation with 60 cp viscous fluid; and (vi) 1 g jacking of the monopile. After spinning up the model to 60 g, the monopile was subjected to lateral one-way sinusoidal and random storm loading using a specially designed hydraulic dynamic actuator that can apply load-controlled time histories in a frequency range of 4–100 Hz in model scale. Selected test results are presented, demonstrating that the experiments successfully captured the partial drainage effects on soil-monopile system response.
- 15 March 2026
- Published by Springer Nature
- p. 668-679
Seismic Behavior of URM Structures: A Centrifuge Model Study
- 15 March 2026
- Published by Springer Nature
- p. 668-679
Seismic Behavior of URM Structures: A Centrifuge Model Study
- Open Access
- 18 February 2026
- Published by Emerald Publishing in International Journal of Physical Modelling in Geotechnics
- Vol. 26 (5) , 240-249
Development of a calibration chamber for a novel in situ testing device
The paper presents the design of a calibration chamber, developed for the testing of a novel self-burrowing probe for in situ soil investigation. The self-burrowing probe is currently under development at ETH Zurich, and its key components will be proof-tested in the controlled environment of the developed chamber. The design of the latter incorporates specific solutions for the testing of the probe: the chamber is equipped with a central opening at the top and base plates, enabling the probe to vertically protrude from the chamber. This aspect is useful for eliminating the tip resistance of the probe and isolating its response, which is relevant when assessing the resistance of the probe’s anchoring system or, in general, for the evaluation of interface properties. The chamber allows for testing under two boundary conditions: (i) zero lateral strain or (ii) constant lateral stress. In the latter case, the radial stress is applied by water pressure inside a membrane, while a pneumatic, doughnut-shaped cushion at the base is used to impose the vertical stress. The paper outlines the key components of the chamber, the sample preparation, and the testing procedures, along with the results of the proof tests conducted in dry Perth sand.
- 18 February 2026
- Published by Emerald Publishing in International Journal of Physical Modelling in Geotechnics
- Vol. 26 (5) , 240-249
Open AccessDevelopment of a calibration chamber for a novel in situ testing device
The paper presents the design of a calibration chamber, developed for the testing of a novel self-burrowing probe for in situ soil investigation. The self-burrowing probe is currently under development at ETH Zurich, and its key components will be proof-tested in the controlled environment of the developed chamber. The design of the latter incorporates specific solutions for the testing of the probe: the chamber is equipped with a central opening at the top and base plates, enabling the probe to vertically protrude from the chamber. This aspect is useful for eliminating the tip resistance of the probe and isolating its response, which is relevant when assessing the resistance of the probe’s anchoring system or, in general, for the evaluation of interface properties. The chamber allows for testing under two boundary conditions: (i) zero lateral strain or (ii) constant lateral stress. In the latter case, the radial stress is applied by water pressure inside a membrane, while a pneumatic, doughnut-shaped cushion at the base is used to impose the vertical stress. The paper outlines the key components of the chamber, the sample preparation, and the testing procedures, along with the results of the proof tests conducted in dry Perth sand.
- Open Access
- 26 November 2025
- Published by Elsevier in Soil Dynamics and Earthquake Engineering
- Vol. 201
Deformation analysis of RC piles and pile groups under combined loading: A nonlinear phenomenological modelling approach
- 26 November 2025
- Published by Elsevier in Soil Dynamics and Earthquake Engineering
- Vol. 201
Open AccessDeformation analysis of RC piles and pile groups under combined loading: A nonlinear phenomenological modelling approach
- Open Access
- 9 December 2024
- Published by Wiley in Earthquake Engineering & Structural Dynamics
- Vol. 54 (3) , 867-884
Seismic Response of Ground Penetrating Shield Tunnels Under Lateral Harmonic Excitations: Insights From Shaking Table Test
The ground penetrating shield tunnel (GPST) method offers a streamlined approach to tunnel construction in soft ground with limited open‐cut excavation. To explore the seismic response of GPST linings, a series of large‐scale shaking table tests have been conducted, including a variety of seismic excitations. This paper focuses on lateral harmonic excitation. The model tunnel spans a total length of 7.7 m, with the embedment depth ranging from −0.5 to 0.5 times its diameter. The design and fabrication of the model tunnel are presented, including the segmental lining, along with circumferential and longitudinal joints. The soil was modeled with artificial synthetic soil, aiming to simulate the static and dynamic characteristics of the prototype soil. Its composition was adjusted and verified through element tests. The experimental results provide insights into the seismic response of the soil–tunnel system, the ovaling deformation of the segmental lining, as well as the response of the joints between lining segments. The results reveal a strong influence of embedment on tunnel seismic response. The reduction of tunnel embedment leads to a significant increase in lining accelerations and a phase difference, resulting in a “whiplash” effect. In contrast, the ovaling deformation of the lining and the joint apertures decrease with the reduction of embedment. In the sections of the tunnel that are fully embedded, both the acceleration and deformation response of the lining are governed by soil–structure interaction (SSI). A pronounced whiplash effect is observed in the sections of the tunnel that are not fully embedded, due to the absence of soil confinement. The presented experimental results offer valuable insights into the seismic response of GPSTs, which can be of crucial importance for their seismic design.
- 9 December 2024
- Published by Wiley in Earthquake Engineering & Structural Dynamics
- Vol. 54 (3) , 867-884
Open AccessSeismic Response of Ground Penetrating Shield Tunnels Under Lateral Harmonic Excitations: Insights From Shaking Table Test
The ground penetrating shield tunnel (GPST) method offers a streamlined approach to tunnel construction in soft ground with limited open‐cut excavation. To explore the seismic response of GPST linings, a series of large‐scale shaking table tests have been conducted, including a variety of seismic excitations. This paper focuses on lateral harmonic excitation. The model tunnel spans a total length of 7.7 m, with the embedment depth ranging from −0.5 to 0.5 times its diameter. The design and fabrication of the model tunnel are presented, including the segmental lining, along with circumferential and longitudinal joints. The soil was modeled with artificial synthetic soil, aiming to simulate the static and dynamic characteristics of the prototype soil. Its composition was adjusted and verified through element tests. The experimental results provide insights into the seismic response of the soil–tunnel system, the ovaling deformation of the segmental lining, as well as the response of the joints between lining segments. The results reveal a strong influence of embedment on tunnel seismic response. The reduction of tunnel embedment leads to a significant increase in lining accelerations and a phase difference, resulting in a “whiplash” effect. In contrast, the ovaling deformation of the lining and the joint apertures decrease with the reduction of embedment. In the sections of the tunnel that are fully embedded, both the acceleration and deformation response of the lining are governed by soil–structure interaction (SSI). A pronounced whiplash effect is observed in the sections of the tunnel that are not fully embedded, due to the absence of soil confinement. The presented experimental results offer valuable insights into the seismic response of GPSTs, which can be of crucial importance for their seismic design.
- 1 August 2024
- Published by Emerald Publishing in Géotechnique
- Vol. 74 (9) , 840-861
On the mechanisms governing the response of pile groups under combined VHM loading
In this paper, an experimental, numerical and analytical study is conducted on a 2 × 1 bored pile group on saturated sand under combined loading. Initially, a single-degree-of-freedom system founded on the pile group is tested at the ETH Zurich drum centrifuge under vertical, lateral and pushover loading, gaining insights and deriving benchmark results for validation of finite-element (FE) models. The latter account for non-linear soil–pile interaction, using hypoplasticity for sand and appropriate modelling of interfaces and pile response. Combining centrifuge and FE modelling, the governing resistance mechanisms are identified and quantified. The transition from model to prototype scale is achieved after careful consideration of scale effects. The concrete damaged plasticity model is employed to model the non-linear response of the reinforced concrete (RC) piles, accounting for axial load dependency of bending moment capacity. The prototype problem is studied parametrically, deriving failure envelopes for different levels of vertical loading. Distinguishable failure modes are identified, and the contribution of different resistance mechanisms is quantified. Finally, analytical failure envelopes are derived based on limit equilibrium, expanding Broms’ theory to pile groups under combined loading. Accounting for the axial load dependency of RC bending moment capacity, the proposed closed-form solutions provide a useful design tool for engineering practice.
- 1 August 2024
- Published by Emerald Publishing in Géotechnique
- Vol. 74 (9) , 840-861
On the mechanisms governing the response of pile groups under combined VHM loading
In this paper, an experimental, numerical and analytical study is conducted on a 2 × 1 bored pile group on saturated sand under combined loading. Initially, a single-degree-of-freedom system founded on the pile group is tested at the ETH Zurich drum centrifuge under vertical, lateral and pushover loading, gaining insights and deriving benchmark results for validation of finite-element (FE) models. The latter account for non-linear soil–pile interaction, using hypoplasticity for sand and appropriate modelling of interfaces and pile response. Combining centrifuge and FE modelling, the governing resistance mechanisms are identified and quantified. The transition from model to prototype scale is achieved after careful consideration of scale effects. The concrete damaged plasticity model is employed to model the non-linear response of the reinforced concrete (RC) piles, accounting for axial load dependency of bending moment capacity. The prototype problem is studied parametrically, deriving failure envelopes for different levels of vertical loading. Distinguishable failure modes are identified, and the contribution of different resistance mechanisms is quantified. Finally, analytical failure envelopes are derived based on limit equilibrium, expanding Broms’ theory to pile groups under combined loading. Accounting for the axial load dependency of RC bending moment capacity, the proposed closed-form solutions provide a useful design tool for engineering practice.
- Open Access
- 10 April 2024
- Published by Elsevier in Soil Dynamics and Earthquake Engineering
- Vol. 181
Analytical 3D failure envelopes for RC pile groups under combined loading: A generalised design approach
- 10 April 2024
- Published by Elsevier in Soil Dynamics and Earthquake Engineering
- Vol. 181
Open AccessAnalytical 3D failure envelopes for RC pile groups under combined loading: A generalised design approach
- Open Access
- 21 December 2023
- Published by Elsevier in Ocean Engineering
- Vol. 292
Offshore foundations in low-plasticity cohesive soils: Cyclic degradation experimental evidence and simplified numerical analysis
- 21 December 2023
- Published by Elsevier in Ocean Engineering
- Vol. 292
Open AccessOffshore foundations in low-plasticity cohesive soils: Cyclic degradation experimental evidence and simplified numerical analysis
- Open Access
- 5 September 2023
- Published by Taylor & Francis in Journal of Earthquake Engineering
- Vol. 28 (6) , 1709-1743
Application of the Εxtended KDamper to the Seismic Protection of Bridges: Design Optimization, Nonlinear Response, SSI and Pounding Effects
- 5 September 2023
- Published by Taylor & Francis in Journal of Earthquake Engineering
- Vol. 28 (6) , 1709-1743
Open AccessApplication of the Εxtended KDamper to the Seismic Protection of Bridges: Design Optimization, Nonlinear Response, SSI and Pounding Effects