Ronald Wbeimar Pacheco Ortiz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Ronald Wbeimar Pacheco Ortiz has a total of 38 co-authors. Here are the top co-authors by number of shared publications:
- João Cajaiba
Universidade Federal do Rio de Janeiro Rua Hélio de Almeida, 40, Cidade Universitária
7 shared publications - Everton Fernando Zanoelo
Department of Chemical Engineering, Federal University of Paraná, Curitiba, Brazil
6 shared publications - Vinicius Kartnaller
Universidade Federal do Rio de Janeiro, Instituto de Química (IQ-UFRJ), Avenida Horácio Macedo, Rio de Janeiro 21941-598, RJ, Brazil
5 shared publications - Vinicius Ottonio Oliveira Gonçalves
NQTR-Núcleo de Desenvolvimento de Processos e Análises Químicas em Tempo Real, Instituto de Química, Universidade Federal do Rio de Janeiro, Rio de Janeiro, Brasil
5 shared publications Fabricio Venancio
Univ Fed Rio de Janeiro NQTR IQ UFRJ, Nucleo Desenvolvimento Proc & Anal Quim Tempo Real, Inst Quim, Rua Helio Almeida 40,Cidade Univ, BR-21940614 Rio De Janeiro, Brazil
3 shared publicationsLúcio Cardozo-Filho
Universidade Estadual de Maringá
3 shared publications
Latest Publications
- Open Access
- 4 August 2026
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 40 (32) , 17565-17578
Integrated Effects of Key Process Variables on CH4–CO2 Exchange in Gas Hydrates: Insights into Driving Forces and Mechanisms
Methane (CH4) hydrates are considered a promising low-carbon energy resource due to their vast global reserves; however, their exploitation poses environmental risks, particularly CH4 leakage. The CH4–CO2 exchange process, also referred to as CH4/CO2 replacement, has been proposed as a strategy to mitigate these risks, as it enables simultaneous CH4 recovery and CO2 sequestration while maintaining sediment integrity. Despite extensive investigation, fundamental questions regarding the driving forces and mechanisms governing this process remain unresolved, limiting large-scale implementation. This study evaluates the integrated effects of key process variables (pressure, temperature, reaction time, initial CH4 and CO2 molar amounts, N2 addition, and biosurfactant presence) on the CH4–CO2 exchange process. The proposed methodology enables systematic investigation in a controlled bulk-hydrate system while incorporating selected reservoir-relevant characteristics, such as the presence of excess free water. Furthermore, GC-BID analysis was employed to obtain quantitative gas-phase compositions during the exchange process. The results indicate that the primary driving force for CH4–CO2 exchange is the tendency toward equalization between gas-phase CO2 and hydrate-phase CH4. A phenomenological model was developed to quantify this effect, describing the observed dependence of exchange efficiency on the initial CO2/CH4 molar balance. Mechanistically, the observed behavior is more readily reconciled with a sequential pathway in which partial destabilization of CH4 hydrates facilitates subsequent CO2 incorporation than with direct guest displacement within an intact CH4 hydrate lattice. Elevated temperatures and reduced pressures favored hydrate destabilization and emerged as important enabling factors for exchange performance. Notably, CO2 addition in the absence of destabilization did not promote CH4 recovery, and N2 addition did not improve exchange performance. These findings provide new mechanistic and quantitative insights into CH4–CO2 exchange and contribute to the development of more efficient CH4 hydrate exploitation and CO2 sequestration strategies.
- 4 August 2026
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 40 (32) , 17565-17578
Open AccessIntegrated Effects of Key Process Variables on CH4–CO2 Exchange in Gas Hydrates: Insights into Driving Forces and Mechanisms
Methane (CH4) hydrates are considered a promising low-carbon energy resource due to their vast global reserves; however, their exploitation poses environmental risks, particularly CH4 leakage. The CH4–CO2 exchange process, also referred to as CH4/CO2 replacement, has been proposed as a strategy to mitigate these risks, as it enables simultaneous CH4 recovery and CO2 sequestration while maintaining sediment integrity. Despite extensive investigation, fundamental questions regarding the driving forces and mechanisms governing this process remain unresolved, limiting large-scale implementation. This study evaluates the integrated effects of key process variables (pressure, temperature, reaction time, initial CH4 and CO2 molar amounts, N2 addition, and biosurfactant presence) on the CH4–CO2 exchange process. The proposed methodology enables systematic investigation in a controlled bulk-hydrate system while incorporating selected reservoir-relevant characteristics, such as the presence of excess free water. Furthermore, GC-BID analysis was employed to obtain quantitative gas-phase compositions during the exchange process. The results indicate that the primary driving force for CH4–CO2 exchange is the tendency toward equalization between gas-phase CO2 and hydrate-phase CH4. A phenomenological model was developed to quantify this effect, describing the observed dependence of exchange efficiency on the initial CO2/CH4 molar balance. Mechanistically, the observed behavior is more readily reconciled with a sequential pathway in which partial destabilization of CH4 hydrates facilitates subsequent CO2 incorporation than with direct guest displacement within an intact CH4 hydrate lattice. Elevated temperatures and reduced pressures favored hydrate destabilization and emerged as important enabling factors for exchange performance. Notably, CO2 addition in the absence of destabilization did not promote CH4 recovery, and N2 addition did not improve exchange performance. These findings provide new mechanistic and quantitative insights into CH4–CO2 exchange and contribute to the development of more efficient CH4 hydrate exploitation and CO2 sequestration strategies.
- 1 July 2024
- Published by Bentham Science Publishers Ltd. in Current Organic Chemistry
- Vol. 28 (14) , 1102-1117
Carboxylic Acids in the Synthesis of Chemicals for Addressing Flow Assurance Challenges in Offshore Petroleum Production
Flow assurance encompasses the technical challenges of transporting hydrocarbon mixtures from the reservoir to the platform and refineries. Challenges in flow assurance include gas hydrate plugs, deposition of paraffin wax, asphaltenes, naphthenates, scale, and corrosion. Managing these deposits incurs high costs due to production interruptions and remediation operations like pigging, solvent injection, acid dissolutions, and thermal treatments. Therefore, prevention methods, such as the use of chemicals that inhibit deposit formation, are preferred. This review consolidates scientific works highlighting the role of carboxylic acids in the synthesis of chemicals for addressing flow assurance challenges as starting materials or final products for direct use. These organic compounds are already employed for the mild remediation of scale and naphthenate deposits and inhibiting gas hydrate, paraffin wax, asphaltene, scale deposits, and corrosion. Moreover, they play a crucial role in developing green flow assurance challenges inhibitors, given that some, like fatty acids, amino acids, and aromatic carboxylic acids, can be derived from natural sources. The presence of the carboxylic acid group in polymers and biopolymers is also essential for the effectiveness of these products as inhibitors. The literature further suggests that carboxylic acids will play a key role in the future development of simultaneous gas hydrate, corrosion, and scale inhibitors.
- 1 July 2024
- Published by Bentham Science Publishers Ltd. in Current Organic Chemistry
- Vol. 28 (14) , 1102-1117
Carboxylic Acids in the Synthesis of Chemicals for Addressing Flow Assurance Challenges in Offshore Petroleum Production
Flow assurance encompasses the technical challenges of transporting hydrocarbon mixtures from the reservoir to the platform and refineries. Challenges in flow assurance include gas hydrate plugs, deposition of paraffin wax, asphaltenes, naphthenates, scale, and corrosion. Managing these deposits incurs high costs due to production interruptions and remediation operations like pigging, solvent injection, acid dissolutions, and thermal treatments. Therefore, prevention methods, such as the use of chemicals that inhibit deposit formation, are preferred. This review consolidates scientific works highlighting the role of carboxylic acids in the synthesis of chemicals for addressing flow assurance challenges as starting materials or final products for direct use. These organic compounds are already employed for the mild remediation of scale and naphthenate deposits and inhibiting gas hydrate, paraffin wax, asphaltene, scale deposits, and corrosion. Moreover, they play a crucial role in developing green flow assurance challenges inhibitors, given that some, like fatty acids, amino acids, and aromatic carboxylic acids, can be derived from natural sources. The presence of the carboxylic acid group in polymers and biopolymers is also essential for the effectiveness of these products as inhibitors. The literature further suggests that carboxylic acids will play a key role in the future development of simultaneous gas hydrate, corrosion, and scale inhibitors.
- 9 November 2023
- Published by Society of Petroleum Engineers (SPE) in SPE Journal
- Vol. 29 (03) , 1528-1539
Evaluating the Potential of Biodegradable Carbohydrates and the Aqueous Extract of Potato Pulp to Inhibit Calcium Carbonate Scale in Petroleum Production
Summary: Scale is a significant operational concern in petroleum production that is commonly addressed by using chemical inhibitors. However, commercial inhibitors can potentially be pollutants depending on their composition and method of disposal. Consequently, evaluating the potential of biodegradable molecules to inhibit scale has gained attention. This study evaluates the effect of a series of carbohydrates (i.e., glucose, fructose, sucrose, maltose, maltodextrin, and soluble starch) and the aqueous extract of potato pulp on calcium carbonate precipitation and scale formation. Precipitation tests were conducted by combining aqueous solutions of sodium bicarbonate (3000 mg L−1) and calcium chloride (4000 mg L−1) in the presence of each carbohydrate, the aqueous extract of potato pulp, or a commercial inhibitor (1000 mg L−1). The precipitation was monitored through RGB (red, green, and blue) image analysis and pH measurements. The induction time in the presence of glucose, fructose, maltose, and sucrose is two to three times longer than in the blank test (in the absence of an inhibitor). This effect is slightly more pronounced in the presence of maltodextrin and soluble starch (approximately four times longer). However, the drop in pH and the mass of solids recovered is similar for all the carbohydrates tested (~0.5 mg and 120 mg, respectively), suggesting that carbohydrates slightly influence the precipitation kinetics but do not affect the precipitation equilibrium. Scanning electron microscopy (SEM) and X-ray powder diffraction (XRD) analysis reveals that calcium carbonate precipitates as calcite and vaterite in the blank test. In the presence of glucose, fructose, maltose, and maltodextrin, calcium carbonate exclusively precipitates as calcite. However, in the presence of sucrose and soluble starch, calcium carbonate precipitates as both calcite and vaterite. Interestingly, a more prominent amount of vaterite was observed in the presence of soluble starch. All carbohydrates decrease the crystallite size of calcite, while sucrose and soluble starch increase the crystallite size of vaterite. The crystalline phases were also identified by Raman spectroscopy, ruling out the presence of any amorphous calcium carbonate phase. The inhibitory effect of soluble starch and the aqueous extract of potato pulp on calcium carbonate scale formation was evaluated in a dynamic scale loop (DSL) system. Soluble starch slightly delays scale formation even at high concentrations (1000 mg L−1). Conversely, the aqueous extract of potato pulp demonstrates enhanced performance by delaying scale formation by approximately 20 minutes for a 1-psi increase in the pressure of the tube and by more than 40 minutes for a 4-psi increase. As a result, it exhibited an impact on the kinetics of solid deposition. This agrees with the precipitation test in the presence of the potato extract (PE), which increases the induction time (from 2 minutes to 32 minutes), decreases the mass of solids (from 116 mg to 35 mg), and forms more distorted and smaller particles of calcite. These findings suggest a promising approach for the development of green scale inhibitors utilizing aqueous extracts of starchy foods or even starchy foods waste water.
- 9 November 2023
- Published by Society of Petroleum Engineers (SPE) in SPE Journal
- Vol. 29 (03) , 1528-1539
Evaluating the Potential of Biodegradable Carbohydrates and the Aqueous Extract of Potato Pulp to Inhibit Calcium Carbonate Scale in Petroleum Production
Summary: Scale is a significant operational concern in petroleum production that is commonly addressed by using chemical inhibitors. However, commercial inhibitors can potentially be pollutants depending on their composition and method of disposal. Consequently, evaluating the potential of biodegradable molecules to inhibit scale has gained attention. This study evaluates the effect of a series of carbohydrates (i.e., glucose, fructose, sucrose, maltose, maltodextrin, and soluble starch) and the aqueous extract of potato pulp on calcium carbonate precipitation and scale formation. Precipitation tests were conducted by combining aqueous solutions of sodium bicarbonate (3000 mg L−1) and calcium chloride (4000 mg L−1) in the presence of each carbohydrate, the aqueous extract of potato pulp, or a commercial inhibitor (1000 mg L−1). The precipitation was monitored through RGB (red, green, and blue) image analysis and pH measurements. The induction time in the presence of glucose, fructose, maltose, and sucrose is two to three times longer than in the blank test (in the absence of an inhibitor). This effect is slightly more pronounced in the presence of maltodextrin and soluble starch (approximately four times longer). However, the drop in pH and the mass of solids recovered is similar for all the carbohydrates tested (~0.5 mg and 120 mg, respectively), suggesting that carbohydrates slightly influence the precipitation kinetics but do not affect the precipitation equilibrium. Scanning electron microscopy (SEM) and X-ray powder diffraction (XRD) analysis reveals that calcium carbonate precipitates as calcite and vaterite in the blank test. In the presence of glucose, fructose, maltose, and maltodextrin, calcium carbonate exclusively precipitates as calcite. However, in the presence of sucrose and soluble starch, calcium carbonate precipitates as both calcite and vaterite. Interestingly, a more prominent amount of vaterite was observed in the presence of soluble starch. All carbohydrates decrease the crystallite size of calcite, while sucrose and soluble starch increase the crystallite size of vaterite. The crystalline phases were also identified by Raman spectroscopy, ruling out the presence of any amorphous calcium carbonate phase. The inhibitory effect of soluble starch and the aqueous extract of potato pulp on calcium carbonate scale formation was evaluated in a dynamic scale loop (DSL) system. Soluble starch slightly delays scale formation even at high concentrations (1000 mg L−1). Conversely, the aqueous extract of potato pulp demonstrates enhanced performance by delaying scale formation by approximately 20 minutes for a 1-psi increase in the pressure of the tube and by more than 40 minutes for a 4-psi increase. As a result, it exhibited an impact on the kinetics of solid deposition. This agrees with the precipitation test in the presence of the potato extract (PE), which increases the induction time (from 2 minutes to 32 minutes), decreases the mass of solids (from 116 mg to 35 mg), and forms more distorted and smaller particles of calcite. These findings suggest a promising approach for the development of green scale inhibitors utilizing aqueous extracts of starchy foods or even starchy foods waste water.
- 21 March 2023
- Published by Wiley in Journal of Food Process Engineering
- Vol. 46 (11)
Novel apparatus for monitoring simultaneously color and °Brix of selected fruit juices through RGB image analysis
This work introduces a novel apparatus for monitoring both color and °Brix of selected fruit juices. These parameters are essential for quality and processing control at concentration and dilution operations. The proposed apparatus performs the red, green, and blue (RGB) image analysis of the fruit juice as it flows through a transparent cell equipped with a webcam and a light source. The viewing cell is inside a box for controlling temperature and for ensuring homogeneous lighting. This apparatus not only measures the RGB color space of the fruit juice online but also allows relating it to the °Brix. The relationship between RGB and °Brix was obtained by measuring the RGB color space of various fruit juice samples, of which the °Brix were previously determined using a digital refractometer. RGB image analysis showed an excellent relationship with °Brix (R2 > 0.99, using an exponential fit), allowing for monitoring reliably this parameter during continuous fruit juice concentration and dilution experiments. These results show the potential of this novel apparatus to substitute conventional instruments such as colorimeters and refractometers for online process monitoring. Furthermore, it has the advantage of not requiring sampling, which reduces measurement errors and saves time.Practical applications: This work introduces a novel apparatus based on RGB image analysis for monitoring simultaneously the color and the °Brix of fruit juices. These parameters are important to control the production and quality of fruit juices, especially at concentration and dilution operations. The apparatus proposed here is a viewing cell where the RGB color space is quantified using the software RGBview® as the fruit juice flows through it. The °Brix are determined from the RGB color space using a suitable fit obtained from a previous calibration with juice samples with known °Brix. This is an alternative to conventional analytical instruments such as colorimeters and refractometers but with the advantage of performing an online measurement. This configuration allows for the reduction of analytical errors associated with sampling and saves time. Moreover, this apparatus has the potential to monitor other physicochemical properties related to the color of fruit juices.
- 21 March 2023
- Published by Wiley in Journal of Food Process Engineering
- Vol. 46 (11)
Novel apparatus for monitoring simultaneously color and °Brix of selected fruit juices through RGB image analysis
This work introduces a novel apparatus for monitoring both color and °Brix of selected fruit juices. These parameters are essential for quality and processing control at concentration and dilution operations. The proposed apparatus performs the red, green, and blue (RGB) image analysis of the fruit juice as it flows through a transparent cell equipped with a webcam and a light source. The viewing cell is inside a box for controlling temperature and for ensuring homogeneous lighting. This apparatus not only measures the RGB color space of the fruit juice online but also allows relating it to the °Brix. The relationship between RGB and °Brix was obtained by measuring the RGB color space of various fruit juice samples, of which the °Brix were previously determined using a digital refractometer. RGB image analysis showed an excellent relationship with °Brix (R2 > 0.99, using an exponential fit), allowing for monitoring reliably this parameter during continuous fruit juice concentration and dilution experiments. These results show the potential of this novel apparatus to substitute conventional instruments such as colorimeters and refractometers for online process monitoring. Furthermore, it has the advantage of not requiring sampling, which reduces measurement errors and saves time.Practical applications: This work introduces a novel apparatus based on RGB image analysis for monitoring simultaneously the color and the °Brix of fruit juices. These parameters are important to control the production and quality of fruit juices, especially at concentration and dilution operations. The apparatus proposed here is a viewing cell where the RGB color space is quantified using the software RGBview® as the fruit juice flows through it. The °Brix are determined from the RGB color space using a suitable fit obtained from a previous calibration with juice samples with known °Brix. This is an alternative to conventional analytical instruments such as colorimeters and refractometers but with the advantage of performing an online measurement. This configuration allows for the reduction of analytical errors associated with sampling and saves time. Moreover, this apparatus has the potential to monitor other physicochemical properties related to the color of fruit juices.
- 20 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 19 (23) , 10991-10998
Real-Time Measurement of pH in Atmospheric and Pressurized Systems Using a Low-Cost Image Analysis Method
The pH is an important parameter to control in many industrial processes carried out at high pressures. However, the measurement of pH in pressurized systems is challenging due to the difficulty in the development of pH sensors resistant to these conditions. This work presents a low-cost technique using image analysis and the hsv (hue, saturation, and value) color system to measure the pH in atmospheric and pressurized systems. First, a calibration curve was prepared with buffer solutions in a pH range from 2 to 10 using a mixture of pH indicators whose color varies at each pH unit. The hsv color system was determined at pressures up to 6.0 MPa and correlated to the pH of each buffer solution. Second, to evaluate the reliability of the relation between pH and hue, an acid–base titration curve with HCl and NaOH was performed. During the titration, the pH was monitored with a pH meter and the results were in good agreement with those obtained from the pH–hue correlation. Finally, to corroborate the applicability of the method in a pressurized system, the CO2–H2O system was studied, determining the pH of pure water pressurized between 0.1 and 5.0 MPa with CO2 at 298 K. The results were similar to theoretical pH values calculated from the solubility of CO2 in water at the experimental conditions. Hence, we have provided a new low-cost method using real-time image analysis and the hsv color system to quantify pH values in atmospheric and pressurized systems, in which the detection sensing achieves accurate measurements.
- 20 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 19 (23) , 10991-10998
Real-Time Measurement of pH in Atmospheric and Pressurized Systems Using a Low-Cost Image Analysis Method
The pH is an important parameter to control in many industrial processes carried out at high pressures. However, the measurement of pH in pressurized systems is challenging due to the difficulty in the development of pH sensors resistant to these conditions. This work presents a low-cost technique using image analysis and the hsv (hue, saturation, and value) color system to measure the pH in atmospheric and pressurized systems. First, a calibration curve was prepared with buffer solutions in a pH range from 2 to 10 using a mixture of pH indicators whose color varies at each pH unit. The hsv color system was determined at pressures up to 6.0 MPa and correlated to the pH of each buffer solution. Second, to evaluate the reliability of the relation between pH and hue, an acid–base titration curve with HCl and NaOH was performed. During the titration, the pH was monitored with a pH meter and the results were in good agreement with those obtained from the pH–hue correlation. Finally, to corroborate the applicability of the method in a pressurized system, the CO2–H2O system was studied, determining the pH of pure water pressurized between 0.1 and 5.0 MPa with CO2 at 298 K. The results were similar to theoretical pH values calculated from the solubility of CO2 in water at the experimental conditions. Hence, we have provided a new low-cost method using real-time image analysis and the hsv color system to quantify pH values in atmospheric and pressurized systems, in which the detection sensing achieves accurate measurements.
- 13 May 2019
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 58 (22) , 9257-9265
Synthesis of Malic Acid on Montmorillonite K10: A Langmuir–Hinshelwood Kinetic Study
- 13 May 2019
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 58 (22) , 9257-9265
Synthesis of Malic Acid on Montmorillonite K10: A Langmuir–Hinshelwood Kinetic Study
- 19 September 2018
- Published by Springer Nature in Reaction Kinetics, Mechanisms and Catalysis
- Vol. 125 (2) , 521-534
Isomerization and hydration of fumaric acid under catalytic and noncatalytic conditions
- 19 September 2018
- Published by Springer Nature in Reaction Kinetics, Mechanisms and Catalysis
- Vol. 125 (2) , 521-534
Isomerization and hydration of fumaric acid under catalytic and noncatalytic conditions
- 12 October 2017
- Published by Springer Nature in Reaction Kinetics, Mechanisms and Catalysis
- Vol. 122 (2) , 793-802
Microwave-assisted synthesis of malic acid involving hydrochloric acid as catalyst
- 12 October 2017
- Published by Springer Nature in Reaction Kinetics, Mechanisms and Catalysis
- Vol. 122 (2) , 793-802
Microwave-assisted synthesis of malic acid involving hydrochloric acid as catalyst