Jun Ogawa
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Jun Ogawa has a total of 102 co-authors. Here are the top co-authors by number of shared publications:
- Satoshi Fukui
Graduate School of Science and Technology, Niigata University, Niigata, Japan
24 shared publications Takao Sato
Graduate School of Science and Technology, Niigata University, Niigata, Japan
10 shared publicationsTetsuo Oka
Graduate School of Science and Technology, Niigata University, Niigata, Japan
9 shared publicationsMitsugi Yamaguchi
6 shared publicationsOsami Tsukamoto
Yokohama National University, Kanagawa, Japan
5 shared publications- Tetsuo Oka
Shibaura Institute of Technology, Tokyo, Japan
5 shared publications
Latest Publications
- 6 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-4
Numerical Investigation of AC Losses in Toroidal Full-Superconducting Resonator Using ReBCO Tapes
High-temperature superconducting (HTS) tapes exhibit a flat plate structure. Experiments have shown the characteristics of pancake-type superconducting capacitor using HTS tapes as electrodes. This pancake-type HTS capacitor also functions as an inductance because it creates a self-magnetic field, and the inductance and capacitance facilitate the creation of an all-superconducting resonant circuit by itself. As AC loss in the HTS circuit is converted into a resistive component, it exerts a significant impact on the Q-factor characteristic, which is the evaluation standard for resonant circuits. Thus, evaluating AC loss characteristics is very important for designing fully superconducting resonant circuits. In this study, the current distribution is not uniform towing to the charge transfer between electrodes in the toroidal full-superconducting resonator; thus, the AC loss was derived in each part using the finite element method (FEM). FEM was employed to derive the AC loss and Q-factor. Considering the resistance component that exists due to the AC losses being nonlinear with respect to the current, a simple equivalent circuit was used to derive the Q-factor.
- 6 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-4
Numerical Investigation of AC Losses in Toroidal Full-Superconducting Resonator Using ReBCO Tapes
High-temperature superconducting (HTS) tapes exhibit a flat plate structure. Experiments have shown the characteristics of pancake-type superconducting capacitor using HTS tapes as electrodes. This pancake-type HTS capacitor also functions as an inductance because it creates a self-magnetic field, and the inductance and capacitance facilitate the creation of an all-superconducting resonant circuit by itself. As AC loss in the HTS circuit is converted into a resistive component, it exerts a significant impact on the Q-factor characteristic, which is the evaluation standard for resonant circuits. Thus, evaluating AC loss characteristics is very important for designing fully superconducting resonant circuits. In this study, the current distribution is not uniform towing to the charge transfer between electrodes in the toroidal full-superconducting resonator; thus, the AC loss was derived in each part using the finite element method (FEM). FEM was employed to derive the AC loss and Q-factor. Considering the resistance component that exists due to the AC losses being nonlinear with respect to the current, a simple equivalent circuit was used to derive the Q-factor.
- 10 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-4
AC Loss Characteristics of High-Temperature Superconducting Tapes Under Over-Current Conditions
The transport current of high-temperature superconducting tapes depends on the critical current value. The upper limit of the transport current is determined by the ratio of the load to the critical current value. In general, direct current must not be regularly energized above the critical current. However, unforeseen events or accidents may result in instantaneous over-currents. This test could be conducted under sufficient cooling; however, the temperature increase causes the critical current value to decrease. Consequently, the loss increases rapidly, resulting in superconducting tape burning out. Conversely, burnout can be prevented under sufficient cooling. This study aimed to investigate the alternating current (AC) loss characteristics by experimentally applying AC above the critical current value of high-temperature superconducting tapes. ReBCO tapes with varying protective layer thicknesses and Bi2223/Ag tapes with different critical current values were subjected to immersion cooling in liquid nitrogen. The four-terminal method was employed to measure the flow of AC above the critical current value. Based on the findings, with adequate cooling, high-temperature superconducting tapes were stably energized even beyond the critical current value.
- 10 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 35 (5) , 1-4
AC Loss Characteristics of High-Temperature Superconducting Tapes Under Over-Current Conditions
The transport current of high-temperature superconducting tapes depends on the critical current value. The upper limit of the transport current is determined by the ratio of the load to the critical current value. In general, direct current must not be regularly energized above the critical current. However, unforeseen events or accidents may result in instantaneous over-currents. This test could be conducted under sufficient cooling; however, the temperature increase causes the critical current value to decrease. Consequently, the loss increases rapidly, resulting in superconducting tape burning out. Conversely, burnout can be prevented under sufficient cooling. This study aimed to investigate the alternating current (AC) loss characteristics by experimentally applying AC above the critical current value of high-temperature superconducting tapes. ReBCO tapes with varying protective layer thicknesses and Bi2223/Ag tapes with different critical current values were subjected to immersion cooling in liquid nitrogen. The four-terminal method was employed to measure the flow of AC above the critical current value. Based on the findings, with adequate cooling, high-temperature superconducting tapes were stably energized even beyond the critical current value.
- 10 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 33 (5) , 1-4
Noncontact Evaluation of HTS Cylinder for Compact Cryogen-Free NMR
Herein, a compact cryogen-free nuclear magnetic resonance (NMR) system is developed using a stacked high-temperature superconducting (HTS) bulk system. To compensate for magnetic field uniformity, an HTS cylinder is installed inside the measurement space. The cylinder is wound with REBCO tapes placed on the surface of a copper cylinder. The uniformity of its critical current density is important for NMR signal detection. Such an operation requires an examination of the quality of the critical-current-density distribution of the cylinder. A noncontact measurement method is required for such an examination. When a magnetic field is applied, the superconductor exhibits a demagnetization effect. Moreover, if any defect exists in any part of the superconducting tape, that particular part would contain no demagnetization, thus disturbing the relevant magnetic field distribution. In this study, this phenomenon is investigated using DC and AC magnetic fields. The magnets and sensor are placed inside the HTS cylinder, and magnetic fields are applied to the HTS cylinder surface. The results confirm that the proposed method is effective and applicable for evaluating the critical-current distribution.
- 10 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 33 (5) , 1-4
Noncontact Evaluation of HTS Cylinder for Compact Cryogen-Free NMR
Herein, a compact cryogen-free nuclear magnetic resonance (NMR) system is developed using a stacked high-temperature superconducting (HTS) bulk system. To compensate for magnetic field uniformity, an HTS cylinder is installed inside the measurement space. The cylinder is wound with REBCO tapes placed on the surface of a copper cylinder. The uniformity of its critical current density is important for NMR signal detection. Such an operation requires an examination of the quality of the critical-current-density distribution of the cylinder. A noncontact measurement method is required for such an examination. When a magnetic field is applied, the superconductor exhibits a demagnetization effect. Moreover, if any defect exists in any part of the superconducting tape, that particular part would contain no demagnetization, thus disturbing the relevant magnetic field distribution. In this study, this phenomenon is investigated using DC and AC magnetic fields. The magnets and sensor are placed inside the HTS cylinder, and magnetic fields are applied to the HTS cylinder surface. The results confirm that the proposed method is effective and applicable for evaluating the critical-current distribution.
- 9 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 33 (5) , 1-4
AC Loss Estimation Model for High-Temperature Superconducting Cables Derived From Experiments Simulating Electromagnetic Environments
In a previous study, the AC loss characteristics of each layer of a high-temperature superconducting (HTS) AC cable were experimentally investigated (Ogawa et al., 2020; Ogawa et al., 2017; Ogawa et al., 2019). Based on these data, we modeled the AC loss in a superconducting cable by considering the maxi-mum and minimum values of the loss. A comparison between this model and the experimental data showed good agreement. Hence, it is possible to estimate AC loss under electromagnetic conditions in a high-temperature superconducting cable. This model makes it possible to determine the losses of each layer in the superconducting cable and to design the minimum AC loss load of the superconducting cable. This model estimates the AC losses of a three-layer twisted HTS cable.
- 9 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 33 (5) , 1-4
AC Loss Estimation Model for High-Temperature Superconducting Cables Derived From Experiments Simulating Electromagnetic Environments
In a previous study, the AC loss characteristics of each layer of a high-temperature superconducting (HTS) AC cable were experimentally investigated (Ogawa et al., 2020; Ogawa et al., 2017; Ogawa et al., 2019). Based on these data, we modeled the AC loss in a superconducting cable by considering the maxi-mum and minimum values of the loss. A comparison between this model and the experimental data showed good agreement. Hence, it is possible to estimate AC loss under electromagnetic conditions in a high-temperature superconducting cable. This model makes it possible to determine the losses of each layer in the superconducting cable and to design the minimum AC loss load of the superconducting cable. This model estimates the AC losses of a three-layer twisted HTS cable.
- 1 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 33 (5) , 1-5
Development of 400 kW Class Aluminum Billet Heater Using HTS Magnet
In this paper, design, fabrication, and test results of the demonstration device for 400 kW-class aluminum billet heating using the HTS magnet were reported. Based on our user's request, the target of the demonstration device was to heat the aluminum billet of 155 mm in diameter and 500 mm in length from room temperature to 500 ℃ within 60 seconds. In the heating test using the demonstration device, it was demonstrated that the input heating power to the aluminum billet of 155 mm in diameter and 500 mm long was more than 400 kW. Based on the measured data of the heating tests, the heating efficiency was estimated to be 74.5%. It was shown that at least 30% reduction of energy consumption could be possible compared to conventional induction heating devices.
- 1 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 33 (5) , 1-5
Development of 400 kW Class Aluminum Billet Heater Using HTS Magnet
In this paper, design, fabrication, and test results of the demonstration device for 400 kW-class aluminum billet heating using the HTS magnet were reported. Based on our user's request, the target of the demonstration device was to heat the aluminum billet of 155 mm in diameter and 500 mm in length from room temperature to 500 ℃ within 60 seconds. In the heating test using the demonstration device, it was demonstrated that the input heating power to the aluminum billet of 155 mm in diameter and 500 mm long was more than 400 kW. Based on the measured data of the heating tests, the heating efficiency was estimated to be 74.5%. It was shown that at least 30% reduction of energy consumption could be possible compared to conventional induction heating devices.
- Open Access
- 20 January 2023
- Published by Cryogenic Association of Japan in Teion Kogaku (Journal of Cryogenics and Superconductivity Society of Japan)
- Vol. 58 (1) , 27-33
Influence of the Current Distribution in Superconducting Resonators for Wireless Power Transmission on the AC Loss Characteristics
This paper investigates the AC loss characteristics in the resonator of the superconducting wireless power transmission system proposed by Prof. Sekiya. This superconducting resonator is characterized by the fact that the current distribution is not constant in the tape length, the REBCO tapes are double layered, and the operating frequency is 10 MHz. Since the influence of eddy current loss cannot be ignored due to the high operating frequency, we investigated the effect of the REBCO tape configuration using the finite element method.
- 20 January 2023
- Published by Cryogenic Association of Japan in Teion Kogaku (Journal of Cryogenics and Superconductivity Society of Japan)
- Vol. 58 (1) , 27-33
Open AccessInfluence of the Current Distribution in Superconducting Resonators for Wireless Power Transmission on the AC Loss Characteristics
This paper investigates the AC loss characteristics in the resonator of the superconducting wireless power transmission system proposed by Prof. Sekiya. This superconducting resonator is characterized by the fact that the current distribution is not constant in the tape length, the REBCO tapes are double layered, and the operating frequency is 10 MHz. Since the influence of eddy current loss cannot be ignored due to the high operating frequency, we investigated the effect of the REBCO tape configuration using the finite element method.
- 20 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 32 (4) , 1-5
Fabrication and Test of HTS Magnet for Induction Heating Device in Aluminum Extrusion Processing
This paper reported the fabrication and the test results of the high temperature superconducting (HTS) magnet developed for the aluminum billet heater for aluminum extrusion processing. In this magnet, the HTS coils were combined with iron cores, because the required magnetic field in the working region was about 1T. Two HTS coils wound directly on the convex shape iron cores were fabricated. The HTS coils were made by the no-insulation winding of REBCO tape with the YOROI-coil technique. Each of them was separately installed in an individual cryostat. Two HTS coils with iron cores were disposed oppositely to each other and were magnetically connected by a C-shape yoke placed in room temperature. The HTS coil was cooled down to about 15 K by the GM cryocooler in the initial cooling. The magnetic field of 1.06 T at the center of the heating region was stably generated with the rated current of 200 A. It was also demonstrated that the HTS magnet could be charged up to 300 A without quench. According to the observation of the electromagnetic force direction from the outside of the cryostat, it was confirmed the validity of the force balance design of the magnet.
- 20 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 32 (4) , 1-5
Fabrication and Test of HTS Magnet for Induction Heating Device in Aluminum Extrusion Processing
This paper reported the fabrication and the test results of the high temperature superconducting (HTS) magnet developed for the aluminum billet heater for aluminum extrusion processing. In this magnet, the HTS coils were combined with iron cores, because the required magnetic field in the working region was about 1T. Two HTS coils wound directly on the convex shape iron cores were fabricated. The HTS coils were made by the no-insulation winding of REBCO tape with the YOROI-coil technique. Each of them was separately installed in an individual cryostat. Two HTS coils with iron cores were disposed oppositely to each other and were magnetically connected by a C-shape yoke placed in room temperature. The HTS coil was cooled down to about 15 K by the GM cryocooler in the initial cooling. The magnetic field of 1.06 T at the center of the heating region was stably generated with the rated current of 200 A. It was also demonstrated that the HTS magnet could be charged up to 300 A without quench. According to the observation of the electromagnetic force direction from the outside of the cryostat, it was confirmed the validity of the force balance design of the magnet.
- 20 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 30 (4) , 1-4
Magnetizing Technique for Permanent Magnets in IPM Motor Rotors Using HTS Bulk Magnet
A unique activation technique for permanent Nd-Fe-B magnets which were embedded in the rotors of interior permanent magnet (IPM) motors has been developed as a magnetizing tool with use of high temperature superconducting (HTS) bulk magnet. The experimental and numerical simulation studies were conducted to evaluate the magnetic field-trapping performances of the rotor of air-conditioner compressor in the hybrid-type automobiles. The sample rotor containing six demagnetized permanent magnet plates were exposed in the intense static magnetic fields above the magnetic pole which contained the bulk magnet generating over 4 T. As a result, the sample magnets were perfectly magnetized in the static magnetic field. The precise simulation on the flux distribution in the rotor clarified that it is important to make the flux direction in the rotor core and the easy magnetization axis of PM identical. We convinced this activation technique should enable us to promote the degrees of freedom of motor designing and its processing.
- 20 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 30 (4) , 1-4
Magnetizing Technique for Permanent Magnets in IPM Motor Rotors Using HTS Bulk Magnet
A unique activation technique for permanent Nd-Fe-B magnets which were embedded in the rotors of interior permanent magnet (IPM) motors has been developed as a magnetizing tool with use of high temperature superconducting (HTS) bulk magnet. The experimental and numerical simulation studies were conducted to evaluate the magnetic field-trapping performances of the rotor of air-conditioner compressor in the hybrid-type automobiles. The sample rotor containing six demagnetized permanent magnet plates were exposed in the intense static magnetic fields above the magnetic pole which contained the bulk magnet generating over 4 T. As a result, the sample magnets were perfectly magnetized in the static magnetic field. The precise simulation on the flux distribution in the rotor clarified that it is important to make the flux direction in the rotor core and the easy magnetization axis of PM identical. We convinced this activation technique should enable us to promote the degrees of freedom of motor designing and its processing.
- 13 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 30 (4) , 1-5
Experimental Investigation of AC Loss Characteristics under HTS Cable Electromagnetic Conditions
- 13 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 30 (4) , 1-5
Experimental Investigation of AC Loss Characteristics under HTS Cable Electromagnetic Conditions
- 31 December 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 30 (4) , 1
Rotational test of an integrated magnetic bearing using multiple HTS cubic bulk units
- 31 December 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. 30 (4) , 1
Rotational test of an integrated magnetic bearing using multiple HTS cubic bulk units