Marco Lorenzo Valerio Tagliaferri
Research Subjects
Marco Lorenzo Valerio Tagliaferri has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
- Marc Sanquer
UMR-E CEA / UJF-Grenoble 1 SPSMS INAC 17 rue des Martyrs 38054 Grenoble France
2 shared publications - Maud Vinet
Univ. Grenoble Alpes, CEA, LETI, Grenoble, France
2 shared publications - Romain Maurand
Univ. Grenoble Alpes
2 shared publications - Silvano De Franceschi
Univ. Grenoble Alpes
2 shared publications - Xavier Jehl
CEA-Grenoble, Université Grenoble Alpes and Grenoble-INP, PHELIQS laboratory, Grenoble, France
2 shared publications A. G. M. Jansen
Univ. Grenoble Alpes, CEA, IRIG/PHELIQS 2 , F-38000 Grenoble
1 shared publication
Latest Publications
- 12 December 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 38.4.1-38.4.4
Dispersive vs charge-sensing readout for linear quantum registers
We present recent progress in the implementation of scalable schemes for spin qubit readout in one dimensional quantum registers based on fully-depleted silicon-on-insulator (FDSOI) technology. We compare two schemes both based on rf gate reflectometry. The first one, denoted as dispersive readout, minimizes the device overhead thereby facilitating scale-up to large qubit registers. The second one, denoted as charge-sensing readout, requires additional readout components but is less sensitive to the strength of the interdot coupling facilitating operation in the few-electron regime. We demonstrate single-shot charge sensing with a fidelity of 97% in 5 μs. Finally, we propose a scalable device architecture for linear qubit registers relying on charge-sensing readout.
- 12 December 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 38.4.1-38.4.4
Dispersive vs charge-sensing readout for linear quantum registers
We present recent progress in the implementation of scalable schemes for spin qubit readout in one dimensional quantum registers based on fully-depleted silicon-on-insulator (FDSOI) technology. We compare two schemes both based on rf gate reflectometry. The first one, denoted as dispersive readout, minimizes the device overhead thereby facilitating scale-up to large qubit registers. The second one, denoted as charge-sensing readout, requires additional readout components but is less sensitive to the strength of the interdot coupling facilitating operation in the few-electron regime. We demonstrate single-shot charge sensing with a fidelity of 97% in 5 μs. Finally, we propose a scalable device architecture for linear qubit registers relying on charge-sensing readout.
- Open Access
- 1 December 2020
- Published by AIP Publishing in Applied Physics Reviews
- Vol. 7 (4) , 041407
Low-power transimpedance amplifier for cryogenic integration with quantum devices
The development of quantum electronic devices operating below a few Kelvin degrees is raising the demand for cryogenic complementary metal-oxide-semiconductor electronics (CMOS) to be used as in situ classical control/readout circuitry. Having a minimal spatial separation between quantum and classical hardware is necessary to limit the electrical wiring to room temperature and the associated heat load and parasitic capacitances. Here, we report prototypical demonstrations of hybrid circuits combining silicon quantum dot devices and a classical transimpedance amplifier, which is characterized and then used to measure the current through the quantum dots. The two devices are positioned next to each other at 4.2 K to assess the use of the cryogenic transimpedance amplifier with respect to a room-temperature transimpedance amplifier. A quantum device built on the same substrate as the transimpedance amplifier is characterized down to 10 mK. The transimpedance amplifier is based on commercial 28 nm fully depleted Silicon-on-insulator (FDSOI) CMOS. It consists of a two-stage Miller-compensated operational amplifier with a 10 MΩ polysilicon feedback resistor, yielding a gain of V/A. We show that the transimpedance amplifier operates at 10 mK with only 1 μW of power consumption, low enough to prevent heating. It exhibits linear response up to ±40 nA and a measurement bandwidth of 2.6 kHz, which could be extended to about 200 kHz by design optimization. The realization of custom-made electronics in FDSOI technology for cryogenic operation at any temperature will improve measurement speed and quality inside cryostats with higher bandwidth, lower noise, and higher signal-to-noise ratio.- 1 December 2020
- Published by AIP Publishing in Applied Physics Reviews
- Vol. 7 (4) , 041407
Open AccessLow-power transimpedance amplifier for cryogenic integration with quantum devices
The development of quantum electronic devices operating below a few Kelvin degrees is raising the demand for cryogenic complementary metal-oxide-semiconductor electronics (CMOS) to be used as in situ classical control/readout circuitry. Having a minimal spatial separation between quantum and classical hardware is necessary to limit the electrical wiring to room temperature and the associated heat load and parasitic capacitances. Here, we report prototypical demonstrations of hybrid circuits combining silicon quantum dot devices and a classical transimpedance amplifier, which is characterized and then used to measure the current through the quantum dots. The two devices are positioned next to each other at 4.2 K to assess the use of the cryogenic transimpedance amplifier with respect to a room-temperature transimpedance amplifier. A quantum device built on the same substrate as the transimpedance amplifier is characterized down to 10 mK. The transimpedance amplifier is based on commercial 28 nm fully depleted Silicon-on-insulator (FDSOI) CMOS. It consists of a two-stage Miller-compensated operational amplifier with a 10 MΩ polysilicon feedback resistor, yielding a gain of V/A. We show that the transimpedance amplifier operates at 10 mK with only 1 μW of power consumption, low enough to prevent heating. It exhibits linear response up to ±40 nA and a measurement bandwidth of 2.6 kHz, which could be extended to about 200 kHz by design optimization. The realization of custom-made electronics in FDSOI technology for cryogenic operation at any temperature will improve measurement speed and quality inside cryostats with higher bandwidth, lower noise, and higher signal-to-noise ratio. - 6 May 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 65 (8) , 1827-1835
Modular Printed Circuit Boards for Broadband Characterization of Nanoelectronic Quantum Devices
We report on the development of a modular system of high-frequency printed circuit boards (PCBs) for electrical low-noise characterization of multigate quantum devices. The whole measurement setup comprises PCBs operating from room temperature to a few kelvins, and custom software to control the broadband electronics held at cryogenic and room temperature. The PCBs coupling scheme and the custom tailoring of the user panel make our platform particularly flexible. At the cryogenic stage, one board hosts the electronics for readout. It consists in a custom complementary metal-oxide-semiconductor circuit for the current sensing. It is composed by a multiplexer for a digital selection of the device under test among up to four samples, connected to a cryogenic transimpedance amplifier with two possible gains, the maximum bandwidth of 250 kHz and the minimum equivalent input noise of 10 fA/√Hz. Such board is coupled to the PCB sample holder, where 14 low-frequency input lines bias the devices and control the gates. Four additional high-frequency input paths with a bandwidth of 1 GHz and an isolation lower than -40 dB at 3 GHz have been implemented to apply a few millivolt pulses with a minimum duration of 1 ns. The PCBs assemblage and the cryogenic electronics are electrically characterized at 4.2 K and later used to perform quantum transport spectroscopy and single-charge dynamics readout at a few microsecond scales in two silicon nanoscaled field-effect transistors.
- 6 May 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 65 (8) , 1827-1835
Modular Printed Circuit Boards for Broadband Characterization of Nanoelectronic Quantum Devices
We report on the development of a modular system of high-frequency printed circuit boards (PCBs) for electrical low-noise characterization of multigate quantum devices. The whole measurement setup comprises PCBs operating from room temperature to a few kelvins, and custom software to control the broadband electronics held at cryogenic and room temperature. The PCBs coupling scheme and the custom tailoring of the user panel make our platform particularly flexible. At the cryogenic stage, one board hosts the electronics for readout. It consists in a custom complementary metal-oxide-semiconductor circuit for the current sensing. It is composed by a multiplexer for a digital selection of the device under test among up to four samples, connected to a cryogenic transimpedance amplifier with two possible gains, the maximum bandwidth of 250 kHz and the minimum equivalent input noise of 10 fA/√Hz. Such board is coupled to the PCB sample holder, where 14 low-frequency input lines bias the devices and control the gates. Four additional high-frequency input paths with a bandwidth of 1 GHz and an isolation lower than -40 dB at 3 GHz have been implemented to apply a few millivolt pulses with a minimum duration of 1 ns. The PCBs assemblage and the cryogenic electronics are electrically characterized at 4.2 K and later used to perform quantum transport spectroscopy and single-charge dynamics readout at a few microsecond scales in two silicon nanoscaled field-effect transistors.