Attila Szlancsik
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Attila Szlancsik has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
- Imre Norbert Orbulov
Department of Materials Science and Engineering, Faculty of Mechanical Engineering, Budapest University of Technology and Economics, Műegyetem rakpart 3., H-1111 Budapest, Hungary MTA-BME Lendület "Momentum" High-performance Composite Metal Foams Research Group, Műegyetem rakpart 3., H-1111 Budapest, Hungary
7 shared publications Dorottya Varga
Budapest University of Technology and Economics
5 shared publicationsBálint Katona
3 shared publications- Bálint Katona
Department of Materials Science and Engineering, Faculty of Mechanical Engineering, Budapest University of Technology and Economics, Műegyetem rakpart 3., 1111 Budapest, Hungary
3 shared publications - Alexandra Kemény
Department of Materials Science and Engineering, Faculty of Mechanical Engineering, Budapest University of Technology and Economics, Budapest, Hungary
2 shared publications - Dóra Károly
Budapest University of Technology and Economics, Faculty of Mechanical Engineering , Department of Materials Science and Engineering , Budapest , Hungary
2 shared publications
Latest Publications
- 8 May 2026
- Published by Elsevier in CIRP Annals
- Vol. 75 (1) , 473-477
Surrogate modelling in axles rolling processes
- 8 May 2026
- Published by Elsevier in CIRP Annals
- Vol. 75 (1) , 473-477
Surrogate modelling in axles rolling processes
- Open Access
- 1 April 2026
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 1348 (1)
Effect of induction heat treatment on residual stresses of a railway brake component
Induction hardening of 42CrMo4 railway brake components was investigated to evaluate residual stress distribution, microstructure, and surface hardness. During the investigations, X-ray diffraction, metallography, and hardness testing were combined with finite element simulations of coupled electromagnetic, thermal, mechanical, and phase transformation phenomena. These results enable targeted residual stress management to improve the fatigue and wear performance of this railway brake part.
- 1 April 2026
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 1348 (1)
Open AccessEffect of induction heat treatment on residual stresses of a railway brake component
Induction hardening of 42CrMo4 railway brake components was investigated to evaluate residual stress distribution, microstructure, and surface hardness. During the investigations, X-ray diffraction, metallography, and hardness testing were combined with finite element simulations of coupled electromagnetic, thermal, mechanical, and phase transformation phenomena. These results enable targeted residual stress management to improve the fatigue and wear performance of this railway brake part.
- Open Access
- 1 April 2026
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 1348 (1)
Development and validation of a micro-tensile tester for lead-free solder alloys
Accurate characterization of material properties is essential for industrial design and development, yet conventional standardized testing methods are not always applicable when only limited material volumes are available or when component dimensions are too small. In such cases, miniaturized specimen testing offers a promising alternative, although its reliable transfer into industrial practice remains a challenge. The present work aims to develop a testing system capable of evaluating miniaturized specimens, including in-situ measurements under a microscope. The design emphasizes precise uniaxial alignment and incorporates a high-resolution load measurement system with an error less than 0.09 N to ensure accuracy at small scales. Special attention is given to minimizing unwanted specimen displacement during in-situ observations, which is critical at high magnifications. In parallel, specimen geometry and fabrication methods are optimized to obtain reproducible results without requiring post-processing. As a first step, miniaturized tensile specimens were produced by casting. The measurement system is controlled by an Arduino Uno, which regulates motion and records force data, while displacement is calculated from stepper motor rotation. The resulting force–displacement curves demonstrate the feasibility of the approach and provide the basis for further refinement of miniaturized mechanical testing systems.
- 1 April 2026
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 1348 (1)
Open AccessDevelopment and validation of a micro-tensile tester for lead-free solder alloys
Accurate characterization of material properties is essential for industrial design and development, yet conventional standardized testing methods are not always applicable when only limited material volumes are available or when component dimensions are too small. In such cases, miniaturized specimen testing offers a promising alternative, although its reliable transfer into industrial practice remains a challenge. The present work aims to develop a testing system capable of evaluating miniaturized specimens, including in-situ measurements under a microscope. The design emphasizes precise uniaxial alignment and incorporates a high-resolution load measurement system with an error less than 0.09 N to ensure accuracy at small scales. Special attention is given to minimizing unwanted specimen displacement during in-situ observations, which is critical at high magnifications. In parallel, specimen geometry and fabrication methods are optimized to obtain reproducible results without requiring post-processing. As a first step, miniaturized tensile specimens were produced by casting. The measurement system is controlled by an Arduino Uno, which regulates motion and records force data, while displacement is calculated from stepper motor rotation. The resulting force–displacement curves demonstrate the feasibility of the approach and provide the basis for further refinement of miniaturized mechanical testing systems.
- Open Access
- 10 September 2025
- Published by Elsevier in Engineering Failure Analysis
- Vol. 182
3D X-ray microscopy and mechanical analysis of thermal cycling-induced degradation in solder joints
- 10 September 2025
- Published by Elsevier in Engineering Failure Analysis
- Vol. 182
Open Access3D X-ray microscopy and mechanical analysis of thermal cycling-induced degradation in solder joints
- 6 January 2025
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 39 (1) , 173-180
Investigating the influence of grain and specimen size on the mechanical properties of coarse grain tensile specimens
- 6 January 2025
- Published by Springer Nature in Journal of Mechanical Science and Technology
- Vol. 39 (1) , 173-180
Investigating the influence of grain and specimen size on the mechanical properties of coarse grain tensile specimens
- Open Access
- 31 August 2024
- Published by Elsevier in Materials Science in Semiconductor Processing
- Vol. 185
A review of the electric measurements and their failure criteria for solder joint degradation
- 31 August 2024
- Published by Elsevier in Materials Science in Semiconductor Processing
- Vol. 185
Open AccessA review of the electric measurements and their failure criteria for solder joint degradation
- Open Access
- 31 July 2023
- Published by Periodica Polytechnica Budapest University of Technology and Economics in Periodica Polytechnica Mechanical Engineering
- Vol. 67 (3) , 252-258
Investigation of the Effect of Heat Treatment Time in Case of Recrystallization of Al99.5
In this study the effect of heat treatment time was investigated in case of recrystallization of Al99.5 material samples. Two different type were manufactured based on the previously applied cold forming. 12% and 24% cold forming was applied to the samples before the heat treatment procedure, which was always at 570 °C and cooled in water. Six different heat treatment time were investigated, namely 5, 10, 30, 60, 120 and 240 minutes. After the recrystallization procedure the microstructure and the mechanical properties were determined. It was found that in the case of the 12% cold formed samples after 30-minute-long heat treatment there were still signs of the original microstructure, however it does not affect the mechanical properties. The yield strength and the ultimate tensile strength were independent of the heat treatment time; they were only dependent on the grain size which was expected. A strong dependency can be discovered between the elongation at break and the heat treatment time. A tangent hyperbolic function was fitted on the measured data, which showed that the asymptote was ~29% for both type of samples. This is a 25% increase compared to the 5-minute-long heat treatment time samples, and this value was reached after ~120 minutes. Another result was that the elongation at break dependency on the grain size is decreasing with increasing heat treatment time.
- 31 July 2023
- Published by Periodica Polytechnica Budapest University of Technology and Economics in Periodica Polytechnica Mechanical Engineering
- Vol. 67 (3) , 252-258
Open AccessInvestigation of the Effect of Heat Treatment Time in Case of Recrystallization of Al99.5
In this study the effect of heat treatment time was investigated in case of recrystallization of Al99.5 material samples. Two different type were manufactured based on the previously applied cold forming. 12% and 24% cold forming was applied to the samples before the heat treatment procedure, which was always at 570 °C and cooled in water. Six different heat treatment time were investigated, namely 5, 10, 30, 60, 120 and 240 minutes. After the recrystallization procedure the microstructure and the mechanical properties were determined. It was found that in the case of the 12% cold formed samples after 30-minute-long heat treatment there were still signs of the original microstructure, however it does not affect the mechanical properties. The yield strength and the ultimate tensile strength were independent of the heat treatment time; they were only dependent on the grain size which was expected. A strong dependency can be discovered between the elongation at break and the heat treatment time. A tangent hyperbolic function was fitted on the measured data, which showed that the asymptote was ~29% for both type of samples. This is a 25% increase compared to the 5-minute-long heat treatment time samples, and this value was reached after ~120 minutes. Another result was that the elongation at break dependency on the grain size is decreasing with increasing heat treatment time.
- Open Access
Verification of the Simulated Carburizing Process in Different Bore Sizes
Carburizing is one of the leading surface treatments in the industry. For this study, 20MnCr5 steel was gas carburized and quenched in real circumstances and simulated with Simufact software. The research investigated the dimensions and types of bores. A through and blind bore was used in this study to analyze how the geometry affects the created layer and, additionally, it takes into account the placement in the heat treatment furnace. An optical microscope and Vickers hardness tester were used to detect the changes in microstructure and measure the layer thickness. After the experiments, a simulation calculated the same variables to compare and validate the results to each other. It can be stated that the placement in the chamber did not influence the form of the high carbon content layer. The simulation and the measured results were in good agreement. The maximum hardness difference was 17%, but the calculated layer thicknesses were always between the measured data. For example, in the case of a small blind bore, the calculated layer thickness was 1.68 ± 0.18 mm, while the measured value was 1.54 ± 0.37 mm. Additionally, the hardness change in depth was similar in both cases. After this validation process, the residual stresses and plastic strains were determined. The maximum residual stresses were similar for every case, namely around 1900 MPa, while the maximum plastic strain was measured in a small blind bore with a value of 0.18. The minimum plastic strain was 0.04 in the through bore.
Open AccessVerification of the Simulated Carburizing Process in Different Bore Sizes
Carburizing is one of the leading surface treatments in the industry. For this study, 20MnCr5 steel was gas carburized and quenched in real circumstances and simulated with Simufact software. The research investigated the dimensions and types of bores. A through and blind bore was used in this study to analyze how the geometry affects the created layer and, additionally, it takes into account the placement in the heat treatment furnace. An optical microscope and Vickers hardness tester were used to detect the changes in microstructure and measure the layer thickness. After the experiments, a simulation calculated the same variables to compare and validate the results to each other. It can be stated that the placement in the chamber did not influence the form of the high carbon content layer. The simulation and the measured results were in good agreement. The maximum hardness difference was 17%, but the calculated layer thicknesses were always between the measured data. For example, in the case of a small blind bore, the calculated layer thickness was 1.68 ± 0.18 mm, while the measured value was 1.54 ± 0.37 mm. Additionally, the hardness change in depth was similar in both cases. After this validation process, the residual stresses and plastic strains were determined. The maximum residual stresses were similar for every case, namely around 1900 MPa, while the maximum plastic strain was measured in a small blind bore with a value of 0.18. The minimum plastic strain was 0.04 in the through bore.
- Open Access
- 23 April 2023
- Published by Elsevier in Materials Today Communications
- Vol. 35
On the compressive properties of aluminum and magnesium syntactic foams: Experiment and simulation
- 23 April 2023
- Published by Elsevier in Materials Today Communications
- Vol. 35
Open AccessOn the compressive properties of aluminum and magnesium syntactic foams: Experiment and simulation
- Open Access
- 23 February 2022
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 31 (9) , 6954-6961
Low-Cost Light-Weight Composite Metal Foams for Transportation Applications
This paper is dealing with the production and investigation (structural and mechanical) of composite metal foams (CMFs) with AlSi9MgMn matrix and ~60 vol% of different nominal diameter light expanded clay particles (LECPs) filler. The main aim was to produce a cheap CMF grade for automotive industry. The samples were produced by liquid state low pressure infiltration. Cubic samples were manufactured from the produced CMF blocks for structural (optical microscopy, scanning electron microscopy and energy-dispersive x-ray spectrometry (EDS)) and for mechanical (compression) investigations and tests. The CMFs were investigated in as-cast and in T6 heat-treated conditions. The macrostructural investigations showed homogenous structure and sufficient quality infiltration. On the microscopic scale, the EDS investigations revealed a complex interface layer affected by chemical reactions between the matrix material and the filler particles. The compressive test proved the classic foam-like mechanical behavior of the CMFs (with long plateau region). A relationship (valid for both the as-cast and T6 heat-treated conditions) was found between the characteristic properties and the nominal diameter of the filler. Based on these results, the LECPs filled CMFs are ideal candidates for automotive applications with tailorable properties.
- 23 February 2022
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 31 (9) , 6954-6961
Open AccessLow-Cost Light-Weight Composite Metal Foams for Transportation Applications
This paper is dealing with the production and investigation (structural and mechanical) of composite metal foams (CMFs) with AlSi9MgMn matrix and ~60 vol% of different nominal diameter light expanded clay particles (LECPs) filler. The main aim was to produce a cheap CMF grade for automotive industry. The samples were produced by liquid state low pressure infiltration. Cubic samples were manufactured from the produced CMF blocks for structural (optical microscopy, scanning electron microscopy and energy-dispersive x-ray spectrometry (EDS)) and for mechanical (compression) investigations and tests. The CMFs were investigated in as-cast and in T6 heat-treated conditions. The macrostructural investigations showed homogenous structure and sufficient quality infiltration. On the microscopic scale, the EDS investigations revealed a complex interface layer affected by chemical reactions between the matrix material and the filler particles. The compressive test proved the classic foam-like mechanical behavior of the CMFs (with long plateau region). A relationship (valid for both the as-cast and T6 heat-treated conditions) was found between the characteristic properties and the nominal diameter of the filler. Based on these results, the LECPs filled CMFs are ideal candidates for automotive applications with tailorable properties.