Yasser Amini
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Yasser Amini has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
- Homayoun Emdad
Shiraz University
7 shared publications E. Izadpanah
Department of Mechanical Engineering, Persian Gulf University, Bushehr, 75169, Iran
3 shared publications- Ehsan Izadpanah
Faculty of Engineering, Persian Gulf University, P.O. Box 75169-13817, Bushehr, Iran
3 shared publications Elham Ebrahimi
3 shared publications- Gholamreza Imani
Mechanical Engineering Department, Persian Gulf University, Bushehr, Iran
3 shared publications Iman Zahed
3 shared publications
Latest Publications
- 1 January 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (1)
Improving the thermal performance of a spherical latent thermal energy storage using innovative fins and porous media
The performance of latent heat thermal energy storage (LHTES) systems can be significantly enhanced by improving the thermal properties of phase change materials (PCMs). Today, these systems serve as a sustainable energy resource and find applications in various sectors, including energy conservation in buildings, household hot water systems, air conditioning units, peak load reduction, waste heat recovery, and biomedical applications. This paper investigates the effects of fins and metal foam on the melting and solidification rates of PCM within a spherical latent heat thermal energy storage unit (LHTESU). To assess the impact of fin geometry on energy storage efficiency, three types of fins were tested: fins with a constant length, fins with a variable length, and curved-shaped fins. Additionally, three different porosity levels of metal foam were considered. A finless reservoir filled with PCM was used as a baseline and benchmark to evaluate the performance enhancements provided by the different fin and metal foam configurations. The results indicated that utilizing seven fixed-length fins with a thickness of 1 mm represents the most effective configuration for increasing melting and solidification rates among the constant volume fraction cases, leading to reductions in melting and solidification times by 58.76% and 72.66%, respectively. Furthermore, incorporating metal foam significantly improved the phase change rate of the PCM, achieving reductions in melting time by 89.11% and solidification time by 94.96% when 85% porosity was used. These results highlight the potential of advanced fin designs and porous media in significantly enhancing the thermal energy storage efficiency, offering promising insights for future sustainable energy technologies.
- 1 January 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (1)
Improving the thermal performance of a spherical latent thermal energy storage using innovative fins and porous media
The performance of latent heat thermal energy storage (LHTES) systems can be significantly enhanced by improving the thermal properties of phase change materials (PCMs). Today, these systems serve as a sustainable energy resource and find applications in various sectors, including energy conservation in buildings, household hot water systems, air conditioning units, peak load reduction, waste heat recovery, and biomedical applications. This paper investigates the effects of fins and metal foam on the melting and solidification rates of PCM within a spherical latent heat thermal energy storage unit (LHTESU). To assess the impact of fin geometry on energy storage efficiency, three types of fins were tested: fins with a constant length, fins with a variable length, and curved-shaped fins. Additionally, three different porosity levels of metal foam were considered. A finless reservoir filled with PCM was used as a baseline and benchmark to evaluate the performance enhancements provided by the different fin and metal foam configurations. The results indicated that utilizing seven fixed-length fins with a thickness of 1 mm represents the most effective configuration for increasing melting and solidification rates among the constant volume fraction cases, leading to reductions in melting and solidification times by 58.76% and 72.66%, respectively. Furthermore, incorporating metal foam significantly improved the phase change rate of the PCM, achieving reductions in melting time by 89.11% and solidification time by 94.96% when 85% porosity was used. These results highlight the potential of advanced fin designs and porous media in significantly enhancing the thermal energy storage efficiency, offering promising insights for future sustainable energy technologies.
- 16 October 2024
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 208
Investigating the effects of near-wall active vortex generators on heat transfer inside a channel
- 16 October 2024
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 208
Investigating the effects of near-wall active vortex generators on heat transfer inside a channel
- 1 August 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (8)
Effects of mass ratio and rotation speed on flow induced vibration of a rotating cylinder with two degrees of freedom
Rotating cylinders submerged in the fluid have many practical applications such as offshore wind turbines and drilling pipes. These rotating cylinders are usually subjected to vortex-induced vibrations, and heat transfer has a great effect on their efficiency. Therefore, it is very important to investigate the heat transfer from the rotating cylinder undergoing vortex-induced vibrations. The present study investigates the flow-induced vibration (FIV) of a rotating circular cylinder, along with the related convective heat transfer, for various mass ratios (mr), rotating rates (α), and a range of reduced velocity (3.0 ≤ ur ≤ 15). The cylinder is modeled as a two-degree-of-freedom system, whereby it is free to oscillate both in the streamwise and transverse directions. The results indicate that the rotational motion of the cylinder significantly enhances the cylinder's displacements in both directions. Furthermore, the displacement amplitude in both directions decreases with an increase in mr. For higher reduced velocities, the displacement amplitude becomes constant. Also, it is observed that increasing mr leads to an improvement in heat transfer for high reduced velocities. Also, the maximum value of the Nusselt number is 15.25 for the non-rotating cylinder and 14 for the rotating cylinder with α=1. The FIV of a rotating circular cylinder exhibits several vortex patterns, including 2S, 2P, P + S, and 2T.
- 1 August 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (8)
Effects of mass ratio and rotation speed on flow induced vibration of a rotating cylinder with two degrees of freedom
Rotating cylinders submerged in the fluid have many practical applications such as offshore wind turbines and drilling pipes. These rotating cylinders are usually subjected to vortex-induced vibrations, and heat transfer has a great effect on their efficiency. Therefore, it is very important to investigate the heat transfer from the rotating cylinder undergoing vortex-induced vibrations. The present study investigates the flow-induced vibration (FIV) of a rotating circular cylinder, along with the related convective heat transfer, for various mass ratios (mr), rotating rates (α), and a range of reduced velocity (3.0 ≤ ur ≤ 15). The cylinder is modeled as a two-degree-of-freedom system, whereby it is free to oscillate both in the streamwise and transverse directions. The results indicate that the rotational motion of the cylinder significantly enhances the cylinder's displacements in both directions. Furthermore, the displacement amplitude in both directions decreases with an increase in mr. For higher reduced velocities, the displacement amplitude becomes constant. Also, it is observed that increasing mr leads to an improvement in heat transfer for high reduced velocities. Also, the maximum value of the Nusselt number is 15.25 for the non-rotating cylinder and 14 for the rotating cylinder with α=1. The FIV of a rotating circular cylinder exhibits several vortex patterns, including 2S, 2P, P + S, and 2T.
- 9 February 2024
- Published by Elsevier in Ocean Engineering
- Vol. 296
A comprehensive study on the power-law fluid flow around and through a porous cylinder with different aspect ratios
- 9 February 2024
- Published by Elsevier in Ocean Engineering
- Vol. 296
A comprehensive study on the power-law fluid flow around and through a porous cylinder with different aspect ratios
- 7 February 2024
- Published by Elsevier in Ocean Engineering
- Vol. 296
Effects of attached flexible splitter plates on flow-induced vibration of two tandem circular cylinders: Two-degree of freedoms study
- 7 February 2024
- Published by Elsevier in Ocean Engineering
- Vol. 296
Effects of attached flexible splitter plates on flow-induced vibration of two tandem circular cylinders: Two-degree of freedoms study
- 12 April 2023
- Published by Springer Nature in Iranian Journal of Science and Technology, Transactions of Mechanical Engineering
- Vol. 48 (1) , 103-118
Numerical Simulation of Pitching Airfoil in the Slip Flow Regime
- 12 April 2023
- Published by Springer Nature in Iranian Journal of Science and Technology, Transactions of Mechanical Engineering
- Vol. 48 (1) , 103-118
Numerical Simulation of Pitching Airfoil in the Slip Flow Regime
- Open Access
- 1 February 2023
- Published by SCI AND TECH UNIVERSAL INC in Scientia Iranica
- Vol. 30 (1) , 64-76
Heat transfer enhancement of a cylinder by flexible fins in turbulent flow
The heat transfer from circular cylinders in turbulent cross flows plays a significant role in industrial operations. The objective of this paper is to evaluate the heat transfer from a cylinder with circular cross section and four flexible fins in turbulent flows numerically. The governing equations of thermal fluid are discretized by finite element method (FEM) while the equations of motion of deformable structure of fins are discretized by finite element method (FEM). The k-ω SST model is used to simulate the flow. The results are validated by comparing the heat transfer rate from the circular cylinder with that of other investigators’ experimental and numerical studies. In addition, the fluid-structure interaction (FSI) results are validated against a benchmark example. The flexible fins are glued to the circular cylinder by two different angles (θ=0° and θ=45°). In both cases, the thermal enhancement, as well as the flow-induced vibrations of the fins, are investigated for various non-dimensional flexural rigidity. It is found that attached fins in both angles and the flexural rigidity are significantly affect Nusselt number. Moreover, it is found that the very flexible fins can increase the Nusselt number by 26%.
- 1 February 2023
- Published by SCI AND TECH UNIVERSAL INC in Scientia Iranica
- Vol. 30 (1) , 64-76
Open AccessHeat transfer enhancement of a cylinder by flexible fins in turbulent flow
The heat transfer from circular cylinders in turbulent cross flows plays a significant role in industrial operations. The objective of this paper is to evaluate the heat transfer from a cylinder with circular cross section and four flexible fins in turbulent flows numerically. The governing equations of thermal fluid are discretized by finite element method (FEM) while the equations of motion of deformable structure of fins are discretized by finite element method (FEM). The k-ω SST model is used to simulate the flow. The results are validated by comparing the heat transfer rate from the circular cylinder with that of other investigators’ experimental and numerical studies. In addition, the fluid-structure interaction (FSI) results are validated against a benchmark example. The flexible fins are glued to the circular cylinder by two different angles (θ=0° and θ=45°). In both cases, the thermal enhancement, as well as the flow-induced vibrations of the fins, are investigated for various non-dimensional flexural rigidity. It is found that attached fins in both angles and the flexural rigidity are significantly affect Nusselt number. Moreover, it is found that the very flexible fins can increase the Nusselt number by 26%.
- 9 May 2022
- Published by SAGE Publications in Journal of Vibration and Control
- Vol. 29 (13-14) , 3064-3077
Hydrodynamic characteristics of flow past a circular cylinder with four attached flexible plates in a high Reynolds number turbulent flow
In this study, the [ ] model is employed to evaluate the effects of flexible plates on the hydrodynamic forces acting on a circular cylinder in turbulent flows. In this regard, four flexible plates are attached to the circular cylinder. Besides, the finite volume method and finite element method have been utilized to discretize the governing equations of the fluid flow and the flexible plates, respectively. The Reynolds number based on the cylinder diameter is kept constant at [ ]. The effects of fin angle [ ] and the flexural rigidity [ ] on the wake structure, displacement amplitude, Strouhal number as well as lift and drag coefficients are investigated. The results showed that the flexural rigidity of plates had a significant influence on the hydrodynamic coefficients. Indeed, an increase in the non-dimensional flexural rigidity enhanced the drag coefficient, and then it approximately remained constant. For [ ] the averaged drag coefficient is approximately constant and equal to 6.1. As the [ ] increases, the drag coefficient increases rapidly and reaches the value of 14.37 for [ ] In the second configuration [ ], values of the drag coefficient for low [ ] and high [ ] values of flexural rigidity are equal to 7.81 and 8.79, respectively.
- 9 May 2022
- Published by SAGE Publications in Journal of Vibration and Control
- Vol. 29 (13-14) , 3064-3077
Hydrodynamic characteristics of flow past a circular cylinder with four attached flexible plates in a high Reynolds number turbulent flow
In this study, the [ ] model is employed to evaluate the effects of flexible plates on the hydrodynamic forces acting on a circular cylinder in turbulent flows. In this regard, four flexible plates are attached to the circular cylinder. Besides, the finite volume method and finite element method have been utilized to discretize the governing equations of the fluid flow and the flexible plates, respectively. The Reynolds number based on the cylinder diameter is kept constant at [ ]. The effects of fin angle [ ] and the flexural rigidity [ ] on the wake structure, displacement amplitude, Strouhal number as well as lift and drag coefficients are investigated. The results showed that the flexural rigidity of plates had a significant influence on the hydrodynamic coefficients. Indeed, an increase in the non-dimensional flexural rigidity enhanced the drag coefficient, and then it approximately remained constant. For [ ] the averaged drag coefficient is approximately constant and equal to 6.1. As the [ ] increases, the drag coefficient increases rapidly and reaches the value of 14.37 for [ ] In the second configuration [ ], values of the drag coefficient for low [ ] and high [ ] values of flexural rigidity are equal to 7.81 and 8.79, respectively.