Rongchuang Chen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Rongchuang Chen has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
- Fei Feng
State Key Laboratory of Material Processing and Die & Mould Technology, Huazhong University of Science and Technology, Wuhan 430074, China
9 shared publications - Jianjun Li
State Key Laboratory of Materials Processing and Die & Mould Technology, College of Materials Science and Engineering, Huazhong University of Science and Technology, Wuhan 430074, China
6 shared publications - Zhizhen Zheng
State Key Laboratory of Materials Processing and Die & Mould Technology, School of Materials Science and Engineering, Huazhong University of Science and Technology, Wuhan 430074, China
4 shared publications - Hongliang Su
State Key Laboratory of Materials Processing and Die & Mould Technology, School of Materials Science and Engineering, Huazhong University of Science and Technology, Wuhan, China
3 shared publications - Min Wang
School of Materials Science and Engineering, Hubei University of Automotive Technology, Shiyan 442002, China
3 shared publications Changbin Wu
Hubei Guang Ao Damper Manufacturing Co. Ltd, Shiyan, China
2 shared publications
Latest Publications
- 28 July 2025
- Published by Springer Nature in Journal of Vibration Engineering & Technologies
- Vol. 13 (6) , 1-20
An Iterative Approach to Solve the Viscous Damper Temperature and the Torsional Vibration Amplitude of a Diesel Engine
- 28 July 2025
- Published by Springer Nature in Journal of Vibration Engineering & Technologies
- Vol. 13 (6) , 1-20
An Iterative Approach to Solve the Viscous Damper Temperature and the Torsional Vibration Amplitude of a Diesel Engine
- 5 November 2024
- Published by IOP Publishing in Physica Scripta
- Vol. 99 (12) , 125214
Torsional damper design for diesel engine: theory and application
Torsional vibration is the primary cause of engine crankshaft failure. Consequently, the reduction of engine vibration is of paramount importance for the enhancement of automotive safety and comfort. However, the lack of comprehensive insight into the damping mechanism of the torsional damper has impeded the effective control of engine torsional vibration. In order to gain insight into the vibration characteristics of the shaft system in an inline six-cylinder diesel engine, an analysis of the system’s behaviour during both free and forced vibration was conducted. A mathematical relationship was deduced between the dimensions, material, operational temperature and damping properties of the silicone oil damper. The objective was to determine the optimal damping and moment of inertia of the damper, with the aim of minimizing the torsional amplitude of the sixth harmonic. The results demonstrate a reduction in the six-harmonic torsional amplitude from 0.32° to 0.14° following the installation of the damper. The mean and relative deviations between the calculated and experimental results are 0.0018° and 0.83%, respectively. To facilitate the design of the silicone oil damper, a software program, Vibsim, was developed based on Visual Studio for the design and torsional vibration analysis of the silicone oil damper. This software is reliable in calculating results and is user-friendly.
- 5 November 2024
- Published by IOP Publishing in Physica Scripta
- Vol. 99 (12) , 125214
Torsional damper design for diesel engine: theory and application
Torsional vibration is the primary cause of engine crankshaft failure. Consequently, the reduction of engine vibration is of paramount importance for the enhancement of automotive safety and comfort. However, the lack of comprehensive insight into the damping mechanism of the torsional damper has impeded the effective control of engine torsional vibration. In order to gain insight into the vibration characteristics of the shaft system in an inline six-cylinder diesel engine, an analysis of the system’s behaviour during both free and forced vibration was conducted. A mathematical relationship was deduced between the dimensions, material, operational temperature and damping properties of the silicone oil damper. The objective was to determine the optimal damping and moment of inertia of the damper, with the aim of minimizing the torsional amplitude of the sixth harmonic. The results demonstrate a reduction in the six-harmonic torsional amplitude from 0.32° to 0.14° following the installation of the damper. The mean and relative deviations between the calculated and experimental results are 0.0018° and 0.83%, respectively. To facilitate the design of the silicone oil damper, a software program, Vibsim, was developed based on Visual Studio for the design and torsional vibration analysis of the silicone oil damper. This software is reliable in calculating results and is user-friendly.
- Open Access
Unified Modelling of Flow Stress and Microstructural Evolution of 300M Steel under Isothermal Tension
Constitutive models that reflect the microstructure evolution is of great significance to accurately predict the forming process of forging. Through thermal tension of 300M steel under various temperatures (950~1150 °C) and strain rates (0.01~10 s−1), the material flow and microstructure evolutions were investigated. In order to describe both the exponential hardening phenomenon at a higher temperature, and the softening phenomenon due to recrystallization at a lower temperature, a constitutive model considering microstructure evolution was proposed based on the Kocks–Mecking model. It was found that considering the stress-strain curve to be exponential in the work-hardening stage could improve the constitutive model prediction precision. The average error was 2.43% (3.59 MPa), showing that the proposed model was more precise than the modified Arrhenius model and the Kocks–Mecking model. The models to describe recrystallization kinetics and average grain size were also constructed. This work enabled the Kocks–Mecking model to predict stress-strain curves with a higher accuracy, and broadened the applicable range of the Kocks–Mecking model.
Open AccessUnified Modelling of Flow Stress and Microstructural Evolution of 300M Steel under Isothermal Tension
Constitutive models that reflect the microstructure evolution is of great significance to accurately predict the forming process of forging. Through thermal tension of 300M steel under various temperatures (950~1150 °C) and strain rates (0.01~10 s−1), the material flow and microstructure evolutions were investigated. In order to describe both the exponential hardening phenomenon at a higher temperature, and the softening phenomenon due to recrystallization at a lower temperature, a constitutive model considering microstructure evolution was proposed based on the Kocks–Mecking model. It was found that considering the stress-strain curve to be exponential in the work-hardening stage could improve the constitutive model prediction precision. The average error was 2.43% (3.59 MPa), showing that the proposed model was more precise than the modified Arrhenius model and the Kocks–Mecking model. The models to describe recrystallization kinetics and average grain size were also constructed. This work enabled the Kocks–Mecking model to predict stress-strain curves with a higher accuracy, and broadened the applicable range of the Kocks–Mecking model.
- 1 February 2021
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 62, 458-470
Multi-point die electromagnetic incremental forming for large-sized sheet metals
- 1 February 2021
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 62, 458-470
Multi-point die electromagnetic incremental forming for large-sized sheet metals
- Open Access
A Flow Stress Model of 300M Steel for Isothermal Tension
To investigate the effect of hot working parameters on the flow behavior of 300M steel under tension, hot uniaxial tensile tests were implemented under different temperatures (950 °C, 1000 °C, 1050 °C, 1100 °C, 1150 °C) and strain rates (0.01 s−1, 0.1 s−1, 1 s−1, 10 s−1). Compared with uniaxial compression, the tensile flow stress was 29.1% higher because dynamic recrystallization softening was less sufficient in the tensile stress state. The ultimate elongation of 300M steel increased with the decrease of temperature and the increase of strain rate. To eliminate the influence of sample necking on stress-strain relationship, both the stress and the strain were calibrated using the cross-sectional area of the neck zone. A constitutive model for tensile deformation was established based on the modified Arrhenius model, in which the model parameters (n, α, Q, ln(A)) were described as a function of strain. The average deviation was 6.81 MPa (6.23%), showing good accuracy of the constitutive model.
Open AccessA Flow Stress Model of 300M Steel for Isothermal Tension
To investigate the effect of hot working parameters on the flow behavior of 300M steel under tension, hot uniaxial tensile tests were implemented under different temperatures (950 °C, 1000 °C, 1050 °C, 1100 °C, 1150 °C) and strain rates (0.01 s−1, 0.1 s−1, 1 s−1, 10 s−1). Compared with uniaxial compression, the tensile flow stress was 29.1% higher because dynamic recrystallization softening was less sufficient in the tensile stress state. The ultimate elongation of 300M steel increased with the decrease of temperature and the increase of strain rate. To eliminate the influence of sample necking on stress-strain relationship, both the stress and the strain were calibrated using the cross-sectional area of the neck zone. A constitutive model for tensile deformation was established based on the modified Arrhenius model, in which the model parameters (n, α, Q, ln(A)) were described as a function of strain. The average deviation was 6.81 MPa (6.23%), showing good accuracy of the constitutive model.
- Open Access
Microstructure Evolution of 5052 Aluminum Sheet in Electromagnetic High-Speed Impact
Electromagnetic forming (EMF) is a high-speed forming technology, which can not only improve the formability of hard-to-form materials but also reduce springback. Electromagnetic high-speed impact can further improve the formability compared with electromagnetic free forming. The microscopic deformation mechanism of electromagnetic high-speed impact of aluminum alloy is discussed in this paper. The microstructures of electromagnetic high-speed impact of an aluminum alloy sheet were characterized. The microscopic deformation mechanisms of electromagnetic forming and electromagnetic high-speed impact were shown, respectively. The research results showed that electromagnetic high-speed impact could significantly improve the microhardness of the workpiece. The grains broke up and then became small subgrains during electromagnetic high-speed impact. The deformation mechanism was dominated by dislocation cross slip under electromagnetic high-speed impact.
Open AccessMicrostructure Evolution of 5052 Aluminum Sheet in Electromagnetic High-Speed Impact
Electromagnetic forming (EMF) is a high-speed forming technology, which can not only improve the formability of hard-to-form materials but also reduce springback. Electromagnetic high-speed impact can further improve the formability compared with electromagnetic free forming. The microscopic deformation mechanism of electromagnetic high-speed impact of aluminum alloy is discussed in this paper. The microstructures of electromagnetic high-speed impact of an aluminum alloy sheet were characterized. The microscopic deformation mechanisms of electromagnetic forming and electromagnetic high-speed impact were shown, respectively. The research results showed that electromagnetic high-speed impact could significantly improve the microhardness of the workpiece. The grains broke up and then became small subgrains during electromagnetic high-speed impact. The deformation mechanism was dominated by dislocation cross slip under electromagnetic high-speed impact.
- Open Access
Flow-Stress Model of 300M Steel for Multi-Pass Compression
In this work, multi-pass compressions were performed at various strain rates (0.01 s−1, 0.1 s−1, 1 s−1, 10 s−1), temperatures (950 °C, 1050 °C, 1150 °C), inter-pass holding time (1 s, 10 s, 30 s, 120 s, 600 s), interrupt strains (0.3, 0.4, 0.5, 0.6), and total pass numbers (1, 2, 3, 4). The intriguing finding was that the recrystallized fraction, average dislocation density, and plastic cumulative strain were partly eliminated during inter-pass holding, resulting in the early occurrence of recrystallization in subsequent compression. Therefore, a parameter (Θ) to evaluate the overall softening fraction due to recrystallization was proposed, and it was then used to iteratively rectify the average dislocation density and plastic cumulative strain in flow-stress modeling. The flow-stress model parameters of 300M steel for multi-pass compression were identified using an optimization technique based on non-derivative method integrated in MATLAB software. The average deviation of calculated and experimental flow-stress was 0.88 MPa (1.35%), showing good accuracy of the flow-stress model. The microstructure evolution of 300M steel was analyzed by the change of softening fraction during multi-pass compression, which provided a useful reference for the research of stress–microstructure relationships of high-strength steels.
Open AccessFlow-Stress Model of 300M Steel for Multi-Pass Compression
In this work, multi-pass compressions were performed at various strain rates (0.01 s−1, 0.1 s−1, 1 s−1, 10 s−1), temperatures (950 °C, 1050 °C, 1150 °C), inter-pass holding time (1 s, 10 s, 30 s, 120 s, 600 s), interrupt strains (0.3, 0.4, 0.5, 0.6), and total pass numbers (1, 2, 3, 4). The intriguing finding was that the recrystallized fraction, average dislocation density, and plastic cumulative strain were partly eliminated during inter-pass holding, resulting in the early occurrence of recrystallization in subsequent compression. Therefore, a parameter (Θ) to evaluate the overall softening fraction due to recrystallization was proposed, and it was then used to iteratively rectify the average dislocation density and plastic cumulative strain in flow-stress modeling. The flow-stress model parameters of 300M steel for multi-pass compression were identified using an optimization technique based on non-derivative method integrated in MATLAB software. The average deviation of calculated and experimental flow-stress was 0.88 MPa (1.35%), showing good accuracy of the flow-stress model. The microstructure evolution of 300M steel was analyzed by the change of softening fraction during multi-pass compression, which provided a useful reference for the research of stress–microstructure relationships of high-strength steels.
- Open Access
Hot Workability of 300M Steel Investigated by In Situ and Ex Situ Compression Tests
In this work, hot compression experiments of 300M steel were performed at 900–1150 °C and 0.01–10 s−1. The relation of flow stress and microstructure evolution was analyzed. The intriguing finding was that at a lower strain rate (0.01 s−1), the flow stress curves were single-peaked, while at a higher strain rate (10 s−1), no peak occurred. Metallographic observation results revealed the phenomenon was because dynamic recrystallization was more complete at a lower strain rate. In situ compression tests were carried out to compare with the results by ex situ compression tests. Hot working maps representing the influences of strains, strain rates, and temperatures were established. It was found that the power dissipation coefficient was not only related to the recrystallized grain size but was also related to the volume fraction of recrystallized grains. The optimal hot working parameters were suggested. This work provides comprehensive understanding of the hot workability of 300M steel in thermal compression.
Open AccessHot Workability of 300M Steel Investigated by In Situ and Ex Situ Compression Tests
In this work, hot compression experiments of 300M steel were performed at 900–1150 °C and 0.01–10 s−1. The relation of flow stress and microstructure evolution was analyzed. The intriguing finding was that at a lower strain rate (0.01 s−1), the flow stress curves were single-peaked, while at a higher strain rate (10 s−1), no peak occurred. Metallographic observation results revealed the phenomenon was because dynamic recrystallization was more complete at a lower strain rate. In situ compression tests were carried out to compare with the results by ex situ compression tests. Hot working maps representing the influences of strains, strain rates, and temperatures were established. It was found that the power dissipation coefficient was not only related to the recrystallized grain size but was also related to the volume fraction of recrystallized grains. The optimal hot working parameters were suggested. This work provides comprehensive understanding of the hot workability of 300M steel in thermal compression.
- Open Access
Flow Behavior and Hot Processing Map of GH4698 for Isothermal Compression Process
An in-depth understanding of the flow behaviors of materials deformed at high temperatures is of paramount significance. However, insufficient research on the nickel-based GH4698 alloy has resulted in inaccurate material flow prediction or even cracking in the practical billet opening of GH4698 large forgings. In this study, hot compressions were performed at 950–1150 °C and 0.001–3 s−1. Single-peaked strain-stress curves were obtained under various conditions, owing to dislocation motions in dynamic recrystallizations. The Arrhenius model was formulated to accurately describe the flow stress evolutions and the mean prediction error of the flow stress was 5.90%. Processing maps were constructed at various hot working conditions. It was found that the hot working ability of GH4698 markedly decreased under lower temperatures (950–1080 °C) and higher strain rates (0.1–3 s−1). Optimal thermal processing parameters were suggested. In sum, this study systematically investigated the flow behaviors and hot working ability of GH4698 in isothermal compressions.
Open AccessFlow Behavior and Hot Processing Map of GH4698 for Isothermal Compression Process
An in-depth understanding of the flow behaviors of materials deformed at high temperatures is of paramount significance. However, insufficient research on the nickel-based GH4698 alloy has resulted in inaccurate material flow prediction or even cracking in the practical billet opening of GH4698 large forgings. In this study, hot compressions were performed at 950–1150 °C and 0.001–3 s−1. Single-peaked strain-stress curves were obtained under various conditions, owing to dislocation motions in dynamic recrystallizations. The Arrhenius model was formulated to accurately describe the flow stress evolutions and the mean prediction error of the flow stress was 5.90%. Processing maps were constructed at various hot working conditions. It was found that the hot working ability of GH4698 markedly decreased under lower temperatures (950–1080 °C) and higher strain rates (0.1–3 s−1). Optimal thermal processing parameters were suggested. In sum, this study systematically investigated the flow behaviors and hot working ability of GH4698 in isothermal compressions.
- 1 October 2018
- Published by Elsevier in Materials Characterization
- Vol. 144, 400-410
In-situ investigation of phase transformation behaviors of 300M steel in continuous cooling process
- 1 October 2018
- Published by Elsevier in Materials Characterization
- Vol. 144, 400-410
In-situ investigation of phase transformation behaviors of 300M steel in continuous cooling process