Jobin Varghese
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Jobin Varghese has a total of 42 co-authors. Here are the top co-authors by number of shared publications:
- Heli Jantunen
Microelectronics Research Unit, Faculty of Information Technology and Electrical Engineering, University of Oulu, Oulu, Finland
7 shared publications - Mailadil Thomas Sebastian
National Institute for Interdisciplinary Science and Technology
4 shared publications Merja Teirikangas
Microelectronics Research Unit, Faculty of Information Technology and Electrical Engineering , University of Oulu , P. O. Box 4500, Oulu FI-90014 , Finland
3 shared publications- Nina Joseph
University of Oulu
3 shared publications Timo Vahera
Microelectronics Research Unit, Faculty of Information Technology and Electrical Engineering , University of Oulu , FI-90014 Oulu , Finland
3 shared publicationsMaciej Sobocinski
Microelectronics Research Unit, Faculty of Information Technology and Electrical Engineering, University of Oulu, FI-90014 Oulu, Finland
2 shared publications
Latest Publications
- Open Access
Fabrication of modern lithium ion batteries by 3D inkjet printing: opportunities and challenges
- Open Access
- 8 October 2020
- Published by Springer Nature
- p. 165-213
Microwave Materials for Defense and Aerospace Applications
- 8 October 2020
- Published by Springer Nature
- p. 165-213
Open AccessMicrowave Materials for Defense and Aerospace Applications
- Open Access
- 22 January 2020
- Published by IntechOpen
Dielectric Losses of Microwave Ceramics Based on Crystal Structure
So far, many microwave dielectric materials have been investigated for a range of telecommunication applications. In dielectrics, the three main dielectric properties are quality factor (Q), dielectric constant and temperature coefficient of resonant frequency. Among these, the most essential dielectric property is Q. More specifically, Q is the inverse of the dielectric loss (tanδ); thus Q = 1/tanδ. There are two kinds of losses: those depending on crystal structure and losses due to external factors. The former is intrinsic losses such as ordering, symmetry, and phonon vibration. The latter is extrinsic losses due to factors such as grain size, defects, inclusions and distortion. In this chapter, the authors present the origin of dielectric losses based on the crystal structure. An ideal and well-proportional crystal structure constitutes a low loss material. Most dielectric materials are paraelectrics with inversion symmetry i and high symmetry. In general, it is believed that ordering gives rise to a high Q, on which many researchers are casting doubt. In the case of complex perovskites, the symmetry changes from cubic to trigonal. Ordering and symmetry should be compared with the structure. In this chapter, three essential conditions for the origin of high Q such as high symmetry, compositional ordering and compositional density are presented.
- 22 January 2020
- Published by IntechOpen
Open AccessDielectric Losses of Microwave Ceramics Based on Crystal Structure
So far, many microwave dielectric materials have been investigated for a range of telecommunication applications. In dielectrics, the three main dielectric properties are quality factor (Q), dielectric constant and temperature coefficient of resonant frequency. Among these, the most essential dielectric property is Q. More specifically, Q is the inverse of the dielectric loss (tanδ); thus Q = 1/tanδ. There are two kinds of losses: those depending on crystal structure and losses due to external factors. The former is intrinsic losses such as ordering, symmetry, and phonon vibration. The latter is extrinsic losses due to factors such as grain size, defects, inclusions and distortion. In this chapter, the authors present the origin of dielectric losses based on the crystal structure. An ideal and well-proportional crystal structure constitutes a low loss material. Most dielectric materials are paraelectrics with inversion symmetry i and high symmetry. In general, it is believed that ordering gives rise to a high Q, on which many researchers are casting doubt. In the case of complex perovskites, the symmetry changes from cubic to trigonal. Ordering and symmetry should be compared with the structure. In this chapter, three essential conditions for the origin of high Q such as high symmetry, compositional ordering and compositional density are presented.
- 13 December 2019
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 12 (1) , 1046-1053
A Temperature-Responsive Copper Molybdate Polymorph Mixture near to Water Boiling Point by a Simple Cryogenic Quenching Route
Smart temperature responsive inorganic materials in accessible temperature ranges open up new positions in the technology. Herein, we present for the first time a CuMoO4 polymorph mixture prepared by a simple cryogenic quenching approach, which offers a fast temperature response close to water boiling temperature for use as a permanent temperature recorder. The new cryogenic quenching technique initiates the formation of a unique polymorph mixture of a deep brown color with a non-uniform combination of γ and α-CuMoO4, with the γ phase confined to the outer region of α-CuMoO4, which has been prepared by conventional solid-state synthesis. In situ structural analysis and refinement results confirm the presence of CuMoO4 α and γ polymorphs, in which the amount of γ polymorph decreases and that of the α phase increases with temperature, accounting for the irreversible thermochromic behavior. The thermal analysis reveals that the polymorph mixture exhibits a fast response with the color changing from deep brown to to bright green with intermediate colors of light brown, yellowish green and light green depending on the exposure temperature as observed from reflectance measurements.
- 13 December 2019
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 12 (1) , 1046-1053
A Temperature-Responsive Copper Molybdate Polymorph Mixture near to Water Boiling Point by a Simple Cryogenic Quenching Route
Smart temperature responsive inorganic materials in accessible temperature ranges open up new positions in the technology. Herein, we present for the first time a CuMoO4 polymorph mixture prepared by a simple cryogenic quenching approach, which offers a fast temperature response close to water boiling temperature for use as a permanent temperature recorder. The new cryogenic quenching technique initiates the formation of a unique polymorph mixture of a deep brown color with a non-uniform combination of γ and α-CuMoO4, with the γ phase confined to the outer region of α-CuMoO4, which has been prepared by conventional solid-state synthesis. In situ structural analysis and refinement results confirm the presence of CuMoO4 α and γ polymorphs, in which the amount of γ polymorph decreases and that of the α phase increases with temperature, accounting for the irreversible thermochromic behavior. The thermal analysis reveals that the polymorph mixture exhibits a fast response with the color changing from deep brown to to bright green with intermediate colors of light brown, yellowish green and light green depending on the exposure temperature as observed from reflectance measurements.
- 11 September 2019
- Published by Springer Nature
- p. 1-48
Microwave Materials for Defense and Aerospace Applications
- 11 September 2019
- Published by Springer Nature
- p. 1-48
Microwave Materials for Defense and Aerospace Applications
- 19 August 2019
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 49 (3) , 1638-1645
PVDF-SIC Composite Thick Films an Effective ESD Composition for Growing Anti-static Applications
- 19 August 2019
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 49 (3) , 1638-1645
PVDF-SIC Composite Thick Films an Effective ESD Composition for Growing Anti-static Applications
- Open Access
- 11 June 2019
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 11 (26) , 23798-23807
Ultra-Low-Temperature Cofired Ceramic Substrates with Low Residual Carbon for Next-Generation Microwave Applications
High temperature cofired ceramics (HTCCs) and low temperature cofired ceramics (LTCCs) are important technologies in the fabrication of multilayer ceramic substrates for discrete devices, electronics packages and telecommunications. However, there is a place and need for materials with lower fabrication temperatures to decrease the associated energy consumption. The present paper studies the feasibility of two ultra-low sintering temperature cofired ceramic (ULTCC) materials, copper molybdate and copper molybdate-Ag2O, sinterable at 650 and 500 °C respectively, for multilayer substrates using tape casting. The slurry composition developed uses environmentally friendly organics and non-toxic binder and solvent. Additionally, the green cast tapes exhibit very low residual carbon (less than 5%) after sintering on analysis by X-ray photoelectron spectroscopy. The multilayer substrates show permittivity values of about 8 with a low dielectric loss in the range of 10-5 to 10-4 in the frequency range of 2-10 GHz along with a low coefficient of thermal expansion in the range of 4-5 ppm/°C and good compatibility with an Al electrode. Thus, these proposed substrates have much promise, with good thermal, mechanical and dielectric properties comparable to commercial substrates while also providing an energy and environment-friendly solution.
- 11 June 2019
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 11 (26) , 23798-23807
Open AccessUltra-Low-Temperature Cofired Ceramic Substrates with Low Residual Carbon for Next-Generation Microwave Applications
High temperature cofired ceramics (HTCCs) and low temperature cofired ceramics (LTCCs) are important technologies in the fabrication of multilayer ceramic substrates for discrete devices, electronics packages and telecommunications. However, there is a place and need for materials with lower fabrication temperatures to decrease the associated energy consumption. The present paper studies the feasibility of two ultra-low sintering temperature cofired ceramic (ULTCC) materials, copper molybdate and copper molybdate-Ag2O, sinterable at 650 and 500 °C respectively, for multilayer substrates using tape casting. The slurry composition developed uses environmentally friendly organics and non-toxic binder and solvent. Additionally, the green cast tapes exhibit very low residual carbon (less than 5%) after sintering on analysis by X-ray photoelectron spectroscopy. The multilayer substrates show permittivity values of about 8 with a low dielectric loss in the range of 10-5 to 10-4 in the frequency range of 2-10 GHz along with a low coefficient of thermal expansion in the range of 4-5 ppm/°C and good compatibility with an Al electrode. Thus, these proposed substrates have much promise, with good thermal, mechanical and dielectric properties comparable to commercial substrates while also providing an energy and environment-friendly solution.
- Open Access
- 7 January 2019
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 7 (4) , 4274-4283
ULTCC Glass Composites Based on Rutile and Anatase with Cofiring at 400 °C for High Frequency Applications
The article presents the very first materials to the Ultra-Low Temperature Co-fired Ceramic (ULTCC) technology with the sintering temperature of 400 °C. The dielectric composites are based on a rutile and anatase with commercial GO17 sealing glass. In addition to the bulk samples, also the tape casting procedure is introduce to showing its feasibility to co-firing with commercial Ag electrodes at 400 °C. The structural, microstructural, thermal and microwave dielectric properties in the green and sintered samples were investigated. The optimum amount of glass to fabricate substrates was found to be 30 vol.%. The ULTCC substrates with the anatase TiO2A-30GO17 and rutile TiO2R-30GO17 were sintered at 400 °C showed a relative permittivity of 9.9 and 15 and a dielectric loss of 0.006 and 0.003, respectively, at the measurement frequency of 9.9 GHz. The temperature dependences of the relative permittivity were +70 and -400 ppm/°C, respectively. Moreover, the coefficients of thermal expansion of the substrates were 7.4 and 8.3 ppm/°C in the measured temperature range of 50-300 °C. A preliminary test to study the feasibility of the anatase TiO2A-30GO17 for a dual band antenna was performed due its relative stable temperature behavior.
- 7 January 2019
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 7 (4) , 4274-4283
Open AccessULTCC Glass Composites Based on Rutile and Anatase with Cofiring at 400 °C for High Frequency Applications
The article presents the very first materials to the Ultra-Low Temperature Co-fired Ceramic (ULTCC) technology with the sintering temperature of 400 °C. The dielectric composites are based on a rutile and anatase with commercial GO17 sealing glass. In addition to the bulk samples, also the tape casting procedure is introduce to showing its feasibility to co-firing with commercial Ag electrodes at 400 °C. The structural, microstructural, thermal and microwave dielectric properties in the green and sintered samples were investigated. The optimum amount of glass to fabricate substrates was found to be 30 vol.%. The ULTCC substrates with the anatase TiO2A-30GO17 and rutile TiO2R-30GO17 were sintered at 400 °C showed a relative permittivity of 9.9 and 15 and a dielectric loss of 0.006 and 0.003, respectively, at the measurement frequency of 9.9 GHz. The temperature dependences of the relative permittivity were +70 and -400 ppm/°C, respectively. Moreover, the coefficients of thermal expansion of the substrates were 7.4 and 8.3 ppm/°C in the measured temperature range of 50-300 °C. A preliminary test to study the feasibility of the anatase TiO2A-30GO17 for a dual band antenna was performed due its relative stable temperature behavior.