Nina Joseph
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Nina Joseph has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Heli Jantunen
Microelectronics Research Unit, Faculty of Information Technology and Electrical Engineering, University of Oulu, Oulu, Finland
3 shared publications - Jobin Varghese
University of Oulu
3 shared publications Merja Teirikangas
Microelectronics Research Unit, Faculty of Information Technology and Electrical Engineering , University of Oulu , P. O. Box 4500, Oulu FI-90014 , Finland
3 shared publicationsHeli Jantunen
Microelectronics Research Unit, Faculty of Information Technology and Electrical Engineering , University of Oulu , P. O. Box 4500, Oulu FI-90014 , Finland
1 shared publication- Hyo Tae Kim
Korea Institute of Ceramic Engineering and Technology
1 shared publication Jobin Varghese
Microelectronics Research Unit, Faculty of Information Technology and Electrical Engineering, University of Oulu, P.O. Box 4500, FI-90014 Oulu, Finland
1 shared publication
Latest Publications
- Open Access
- 8 October 2020
- Published by Springer Nature
- p. 165-213
Microwave Materials for Defense and Aerospace Applications
- 8 October 2020
- Published by Springer Nature
- p. 165-213
Open AccessMicrowave Materials for Defense and Aerospace Applications
- 13 December 2019
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 12 (1) , 1046-1053
A Temperature-Responsive Copper Molybdate Polymorph Mixture near to Water Boiling Point by a Simple Cryogenic Quenching Route
Smart temperature responsive inorganic materials in accessible temperature ranges open up new positions in the technology. Herein, we present for the first time a CuMoO4 polymorph mixture prepared by a simple cryogenic quenching approach, which offers a fast temperature response close to water boiling temperature for use as a permanent temperature recorder. The new cryogenic quenching technique initiates the formation of a unique polymorph mixture of a deep brown color with a non-uniform combination of γ and α-CuMoO4, with the γ phase confined to the outer region of α-CuMoO4, which has been prepared by conventional solid-state synthesis. In situ structural analysis and refinement results confirm the presence of CuMoO4 α and γ polymorphs, in which the amount of γ polymorph decreases and that of the α phase increases with temperature, accounting for the irreversible thermochromic behavior. The thermal analysis reveals that the polymorph mixture exhibits a fast response with the color changing from deep brown to to bright green with intermediate colors of light brown, yellowish green and light green depending on the exposure temperature as observed from reflectance measurements.
- 13 December 2019
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 12 (1) , 1046-1053
A Temperature-Responsive Copper Molybdate Polymorph Mixture near to Water Boiling Point by a Simple Cryogenic Quenching Route
Smart temperature responsive inorganic materials in accessible temperature ranges open up new positions in the technology. Herein, we present for the first time a CuMoO4 polymorph mixture prepared by a simple cryogenic quenching approach, which offers a fast temperature response close to water boiling temperature for use as a permanent temperature recorder. The new cryogenic quenching technique initiates the formation of a unique polymorph mixture of a deep brown color with a non-uniform combination of γ and α-CuMoO4, with the γ phase confined to the outer region of α-CuMoO4, which has been prepared by conventional solid-state synthesis. In situ structural analysis and refinement results confirm the presence of CuMoO4 α and γ polymorphs, in which the amount of γ polymorph decreases and that of the α phase increases with temperature, accounting for the irreversible thermochromic behavior. The thermal analysis reveals that the polymorph mixture exhibits a fast response with the color changing from deep brown to to bright green with intermediate colors of light brown, yellowish green and light green depending on the exposure temperature as observed from reflectance measurements.
- Open Access
- 11 June 2019
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 11 (26) , 23798-23807
Ultra-Low-Temperature Cofired Ceramic Substrates with Low Residual Carbon for Next-Generation Microwave Applications
High temperature cofired ceramics (HTCCs) and low temperature cofired ceramics (LTCCs) are important technologies in the fabrication of multilayer ceramic substrates for discrete devices, electronics packages and telecommunications. However, there is a place and need for materials with lower fabrication temperatures to decrease the associated energy consumption. The present paper studies the feasibility of two ultra-low sintering temperature cofired ceramic (ULTCC) materials, copper molybdate and copper molybdate-Ag2O, sinterable at 650 and 500 °C respectively, for multilayer substrates using tape casting. The slurry composition developed uses environmentally friendly organics and non-toxic binder and solvent. Additionally, the green cast tapes exhibit very low residual carbon (less than 5%) after sintering on analysis by X-ray photoelectron spectroscopy. The multilayer substrates show permittivity values of about 8 with a low dielectric loss in the range of 10-5 to 10-4 in the frequency range of 2-10 GHz along with a low coefficient of thermal expansion in the range of 4-5 ppm/°C and good compatibility with an Al electrode. Thus, these proposed substrates have much promise, with good thermal, mechanical and dielectric properties comparable to commercial substrates while also providing an energy and environment-friendly solution.
- 11 June 2019
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 11 (26) , 23798-23807
Open AccessUltra-Low-Temperature Cofired Ceramic Substrates with Low Residual Carbon for Next-Generation Microwave Applications
High temperature cofired ceramics (HTCCs) and low temperature cofired ceramics (LTCCs) are important technologies in the fabrication of multilayer ceramic substrates for discrete devices, electronics packages and telecommunications. However, there is a place and need for materials with lower fabrication temperatures to decrease the associated energy consumption. The present paper studies the feasibility of two ultra-low sintering temperature cofired ceramic (ULTCC) materials, copper molybdate and copper molybdate-Ag2O, sinterable at 650 and 500 °C respectively, for multilayer substrates using tape casting. The slurry composition developed uses environmentally friendly organics and non-toxic binder and solvent. Additionally, the green cast tapes exhibit very low residual carbon (less than 5%) after sintering on analysis by X-ray photoelectron spectroscopy. The multilayer substrates show permittivity values of about 8 with a low dielectric loss in the range of 10-5 to 10-4 in the frequency range of 2-10 GHz along with a low coefficient of thermal expansion in the range of 4-5 ppm/°C and good compatibility with an Al electrode. Thus, these proposed substrates have much promise, with good thermal, mechanical and dielectric properties comparable to commercial substrates while also providing an energy and environment-friendly solution.
- 13 September 2016
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 4 (10) , 5632-5639
Glass-Free CuMoO4 Ceramic with Excellent Dielectric and Thermal Properties for Ultralow Temperature Cofired Ceramic Applications
- 13 September 2016
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 4 (10) , 5632-5639
Glass-Free CuMoO4 Ceramic with Excellent Dielectric and Thermal Properties for Ultralow Temperature Cofired Ceramic Applications