Van-The Tran
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Van-The Tran has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
Minh-Thuan Hoang
Hung Yen University of Technology and Education
3 shared publications- Vu Duc Phuc
Hung Yen University of Technology and Education
3 shared publications Banh Tien-Long
Hung Yen University of Technology and Education
2 shared publications- Chung-Biau Tsay
Department of Mechanical Engineering, National Chiao Tung University, Hsinchu 30010, Taiwan, ROC
2 shared publications Nguyen Thanh Tung
Hung Yen University of Technology and Education
2 shared publications- Ruei-Hung Hsu
Feng Chia University
2 shared publications
Latest Publications
- Open Access
- 30 September 2026
- Published by OU Scientific Route in EUREKA: Physics and Engineering
- No. 5,p. 136-147
Development of a method for optimizing the rotor profile to improve roots pump performance based on sequential unconstrained minimization technique
Roots pumps are widely used in life and industrial applications, and their rotors are a key factor in improving pump performance. The rotor profile of a Roots pump is critical to its performance because it transfers gas into the housing. The rotor profile of a Roots pump is usually composed of various curves, and its design parameters are numerous and difficult to optimize. Therefore, a method for optimizing the rotor profile of a Roots pump is needed to improve pump performance. This paper proposes a novel method for optimizing the rotor profile of a Roots pump based on the sequential unconstrained minimization technique. Firstly, a mathematical model of the rotor profile, combined with a circle arc, an involute curve and a circle arc, is proposed. The rotor profile of the roots pump is designed with geometric constraints to ensure the curves connect smoothly. Then, the geometric indices of the rotor profile, including area utilization efficiency and dimensionless sealing line length, are defined and optimized to improve pump performance using a sequential unconstrained minimization technique. Numerical examples verify the effectiveness of the proposed method in optimizing the rotor profile and enhancing Roots pump performance. The numerical results show that the Roots pump performance is enhanced through a reduced sealing line length of 0.86% and an increase in area utilization efficiency of 0.61%. The proposed method for optimizing the rotor profile based on the sequential unconstrained minimization technique applies not only to Roots pumps but also to other pump types.
- 30 September 2026
- Published by OU Scientific Route in EUREKA: Physics and Engineering
- No. 5,p. 136-147
Open AccessDevelopment of a method for optimizing the rotor profile to improve roots pump performance based on sequential unconstrained minimization technique
Roots pumps are widely used in life and industrial applications, and their rotors are a key factor in improving pump performance. The rotor profile of a Roots pump is critical to its performance because it transfers gas into the housing. The rotor profile of a Roots pump is usually composed of various curves, and its design parameters are numerous and difficult to optimize. Therefore, a method for optimizing the rotor profile of a Roots pump is needed to improve pump performance. This paper proposes a novel method for optimizing the rotor profile of a Roots pump based on the sequential unconstrained minimization technique. Firstly, a mathematical model of the rotor profile, combined with a circle arc, an involute curve and a circle arc, is proposed. The rotor profile of the roots pump is designed with geometric constraints to ensure the curves connect smoothly. Then, the geometric indices of the rotor profile, including area utilization efficiency and dimensionless sealing line length, are defined and optimized to improve pump performance using a sequential unconstrained minimization technique. Numerical examples verify the effectiveness of the proposed method in optimizing the rotor profile and enhancing Roots pump performance. The numerical results show that the Roots pump performance is enhanced through a reduced sealing line length of 0.86% and an increase in area utilization efficiency of 0.61%. The proposed method for optimizing the rotor profile based on the sequential unconstrained minimization technique applies not only to Roots pumps but also to other pump types.
- 17 February 2025
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 240 (3) , 3328-3337
A novel profile considered geometry optimization for unequal rotor pair of claw-type vacuum pump
In the claw-type vacuum pumps, the rotor pair is a vital component, the rotor profiles are mainly affected by the performance of the claw-type vacuum pumps. Therefore, this study proposes a novel profile for unequal rotor pair considered geometry optimization to improve the performance of claw-type vacuum pumps. The proposed unequal rotor pair's geometric models and profile equations are established since geometry parameters of unequal rotor profile evaluated and optimized to improve the performance of claw-type vacuum pump. Moreover, the influence of geometry parameters on the working area ratio and sealing line length are presented. The numerical results indicate that the performance of claw-type vacuum pumps with novel unequal rotor profiles has improved significantly compared to the traditional rotor profile. The working area ratio of the proposed pump is higher 7.2% than that of the traditional pump. The working sealing line length of the proposed pump is shorter 31.89% than that of the traditional pump.
- 17 February 2025
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 240 (3) , 3328-3337
A novel profile considered geometry optimization for unequal rotor pair of claw-type vacuum pump
In the claw-type vacuum pumps, the rotor pair is a vital component, the rotor profiles are mainly affected by the performance of the claw-type vacuum pumps. Therefore, this study proposes a novel profile for unequal rotor pair considered geometry optimization to improve the performance of claw-type vacuum pumps. The proposed unequal rotor pair's geometric models and profile equations are established since geometry parameters of unequal rotor profile evaluated and optimized to improve the performance of claw-type vacuum pump. Moreover, the influence of geometry parameters on the working area ratio and sealing line length are presented. The numerical results indicate that the performance of claw-type vacuum pumps with novel unequal rotor profiles has improved significantly compared to the traditional rotor profile. The working area ratio of the proposed pump is higher 7.2% than that of the traditional pump. The working sealing line length of the proposed pump is shorter 31.89% than that of the traditional pump.
- 14 February 2025
- Published by Springer Nature
- p. 629-637
A Design Review for Generating Involute Tooth Profile of Non-circular Gear Pair
- 14 February 2025
- Published by Springer Nature
- p. 629-637
A Design Review for Generating Involute Tooth Profile of Non-circular Gear Pair
- 7 January 2024
- Published by Springer Nature in International Journal on Interactive Design and Manufacturing (IJIDeM)
- Vol. 18 (7) , 4463-4476
The Side-Cutter Position Adjustment Method for Enhancing Milled Rotor Profile Accuracy using ANN and NSGA-II
- 7 January 2024
- Published by Springer Nature in International Journal on Interactive Design and Manufacturing (IJIDeM)
- Vol. 18 (7) , 4463-4476
The Side-Cutter Position Adjustment Method for Enhancing Milled Rotor Profile Accuracy using ANN and NSGA-II
- 17 November 2022
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
- Vol. 237 (10) , 1582-1595
Methodology for generating a general profile of asymmetrical rotors of twin-screw vacuum pumps with point meshing feature by a pre-defined sealing line
The sealing line is one of the key influences on twin-screw rotor vacuum pump performance. The design of a rotor profile based on a sealing line for an asymmetrical rotor of a vacuum pump can be studied further to generate varied rotor profiles and improve pump performance. Therefore, this study proposes a mathematical model for a pre-defined sealing line to design and optimize varied rotor profiles of vacuum pumps. The general sealing line, pre-defined by explicit equations of straight lines and elliptic curves, is proposed to generate various rotor profiles with different numbers of lobes. The functions for parameter variables of the pre-defined sealing line are constructed and directly variated along the rotor length to form the screw rotor with a variable pitch and a variable cross-section. The proposed pre-defined sealing line is also applied in the optimal design of a rotor profile to enhance pump performance. Numerical examples are performed to verify the flexibility and practicability of the proposed method.
- 17 November 2022
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
- Vol. 237 (10) , 1582-1595
Methodology for generating a general profile of asymmetrical rotors of twin-screw vacuum pumps with point meshing feature by a pre-defined sealing line
The sealing line is one of the key influences on twin-screw rotor vacuum pump performance. The design of a rotor profile based on a sealing line for an asymmetrical rotor of a vacuum pump can be studied further to generate varied rotor profiles and improve pump performance. Therefore, this study proposes a mathematical model for a pre-defined sealing line to design and optimize varied rotor profiles of vacuum pumps. The general sealing line, pre-defined by explicit equations of straight lines and elliptic curves, is proposed to generate various rotor profiles with different numbers of lobes. The functions for parameter variables of the pre-defined sealing line are constructed and directly variated along the rotor length to form the screw rotor with a variable pitch and a variable cross-section. The proposed pre-defined sealing line is also applied in the optimal design of a rotor profile to enhance pump performance. Numerical examples are performed to verify the flexibility and practicability of the proposed method.
- 4 May 2022
- Published by Springer Nature
- p. 3-9
Research on Generating CIC Tooth Profile of Rotor in Vacuum Pumps
- 4 May 2022
- Published by Springer Nature
- p. 3-9
Research on Generating CIC Tooth Profile of Rotor in Vacuum Pumps
- 21 December 2021
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part K: Journal of Multi-Body Dynamics
- Vol. 236 (1) , 41-50
Optimization design for multiple dynamic vibration absorbers on damped structures using equivalent linearization method
The dynamic vibration absorber and tuned mass damper are widely used to suppress harmful vibration of the damped structures under external excitation. The multiple dynamic vibration absorbers have more benefit than the single dynamic vibration absorber. The multiple dynamic vibration absorbers are portability and easy to install because its size is significantly reduced compared to an individual damper. This paper proposes a design method to obtain optimal parameters of multiple dynamic vibration absorbers attached on damped primary structures by using the least squares estimation of equivalent linearization method. An explicit expression of damping ratio and tuning parameters of multiple dynamic vibration absorbers are determined for minimizing the maximum displacement of the primary structures based on the fixed-point theory. The new contribution is provided a reliable theoretical basis for optimizing parameters of the multiple dynamic vibration absorbers that are attached on the damped primary structures. The numerical results reveal the effectiveness of the proposed optimal parameters of multiple dynamic vibration absorbers in reduce vibration of damped primary structures. In the practical applications, this research results allow to divide a large dynamic vibration absorber into many equivalent small dynamic vibration absorbers, which are convenient for manufacturing and installing on the damped primary structures such as high buildings and cable-stayed bridges.
- 21 December 2021
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part K: Journal of Multi-Body Dynamics
- Vol. 236 (1) , 41-50
Optimization design for multiple dynamic vibration absorbers on damped structures using equivalent linearization method
The dynamic vibration absorber and tuned mass damper are widely used to suppress harmful vibration of the damped structures under external excitation. The multiple dynamic vibration absorbers have more benefit than the single dynamic vibration absorber. The multiple dynamic vibration absorbers are portability and easy to install because its size is significantly reduced compared to an individual damper. This paper proposes a design method to obtain optimal parameters of multiple dynamic vibration absorbers attached on damped primary structures by using the least squares estimation of equivalent linearization method. An explicit expression of damping ratio and tuning parameters of multiple dynamic vibration absorbers are determined for minimizing the maximum displacement of the primary structures based on the fixed-point theory. The new contribution is provided a reliable theoretical basis for optimizing parameters of the multiple dynamic vibration absorbers that are attached on the damped primary structures. The numerical results reveal the effectiveness of the proposed optimal parameters of multiple dynamic vibration absorbers in reduce vibration of damped primary structures. In the practical applications, this research results allow to divide a large dynamic vibration absorber into many equivalent small dynamic vibration absorbers, which are convenient for manufacturing and installing on the damped primary structures such as high buildings and cable-stayed bridges.
- 27 March 2021
- Published by Springer Nature
- p. 943-951
Analyzing Dynamic Characteristics of Working Rotor Pair in Vacuum Pumps
- 27 March 2021
- Published by Springer Nature
- p. 943-951
Analyzing Dynamic Characteristics of Working Rotor Pair in Vacuum Pumps
- Open Access
- 26 August 2019
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 11 (8)
A study on a deep-drawing process with two shaping states for a fuel-filter cup using combined simulation and experiment
In this article, a deep-drawing process using a double-action hydraulic press is examined for its ability to machine the shaping deformation of a fuel-filter cup made from SPCC steel. Many researchers have studied the geometric, physical, and technological parameters of the deep-drawing process. However, most of those studies ignored the optimization parameters of the two shaping deformation states to ensure uniformity of thickness and the disappearance of wrinkling and tearing during machining. In this study, geometric and technological parameters (e.g. blank-holder force, die-shoulder radius, and radial clearance between punch and die) are optimized in both states. The deep-drawing process for a fuel-filter cup is simulated using ABAQUS software, and optimal parameters are determined by applying the Taguchi orthogonal array computation and combining it with an analysis of variance method. The numerical results are then verified with corresponding experiments. The obtained numerical and experimental results show that the die-shoulder radius is one of the most influential parameters affecting the shaping of the cup during the deep-drawing process. Moreover, the influences of technological parameters on the formability of sheet metal are finally analyzed and selected for designing and improving deep-drawing molds.
- 26 August 2019
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 11 (8)
Open AccessA study on a deep-drawing process with two shaping states for a fuel-filter cup using combined simulation and experiment
In this article, a deep-drawing process using a double-action hydraulic press is examined for its ability to machine the shaping deformation of a fuel-filter cup made from SPCC steel. Many researchers have studied the geometric, physical, and technological parameters of the deep-drawing process. However, most of those studies ignored the optimization parameters of the two shaping deformation states to ensure uniformity of thickness and the disappearance of wrinkling and tearing during machining. In this study, geometric and technological parameters (e.g. blank-holder force, die-shoulder radius, and radial clearance between punch and die) are optimized in both states. The deep-drawing process for a fuel-filter cup is simulated using ABAQUS software, and optimal parameters are determined by applying the Taguchi orthogonal array computation and combining it with an analysis of variance method. The numerical results are then verified with corresponding experiments. The obtained numerical and experimental results show that the die-shoulder radius is one of the most influential parameters affecting the shaping of the cup during the deep-drawing process. Moreover, the influences of technological parameters on the formability of sheet metal are finally analyzed and selected for designing and improving deep-drawing molds.