ELE. G. Len

E. G. Len

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


E. G. Len has a total of 88 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    THE EFFECT OF DEFECTS OF VARIOUS GENESIS ON THE PROPERTIES OF CARBON NANOTUBES

    by Halyna Mykhailova, Mykola Shevchenko, Ihor Danylenko, Mykola Skoryk, Dmitry Vedel, Vitaliy Lebed, Volodymyr Koda, Evgen Len

    We investigate how growth-related and γ-radiation-induced defects jointly control the electrical, thermoelectric, and elastic response of bulk arrays of highly defective multiwalled carbon nanotubes (MWCNTs). The MWCNT arrays were irradiated by 1.2 MeV γ-quanta in the dose range (1.63–32.8)×10¹⁶ γ/cm². Defect evolution was tracked by Raman spectroscopy (λ = 532 nm), SEM, and EDX, while the electrical conductivity and thermo-EMF (Seebeck coefficient) were measured under moderate compression, i.e., in the regime where transport is governed by percolation through intertube junctions and their tunneling or contact barriers. The dose response is nonmonotonic: conductivity increases quasi-linearly at low doses and reaches a broad maximum near 17.08×10¹⁶ γ/cm², followed by a slight decrease at 32.8×10¹⁶ γ/cm². Raman data indicate that γ-irradiation does not merely accumulate disorder: the smallest dose produces a sharp increase of the effective size of ordered sp²-regiones, consistent with deoxygenation and partial reconstruction of growth defects, whereas the intermediate dose ∼4.51×1016 γ/cm²) corresponds to the maximum spatial heterogeneity (largest line widths and scatter of the parameters throughout the sample), and the highest doses promote morphological thinning and loosening (seen by SEM). At the microscopic level, topological rearrangements of graphene layers of different genesis (growth and radiation), together with vacancy-type disorder, alter MWCNT curvature and junction geometry and thereby reshape the percolation and contact-barrier landscape that governs both conductivity and thermo-EMF. Overall, transport is controlled by the coupled evolution of intertube contacts and intratube defects under competition between partial healing and radiation damage.

  • Open Access

    Effect of caesium adsorption on the emission properties of tungsten and molybdenum single-crystal surfaces (100) and (110) for application in nuclear and thermonuclear reactors

    by I. Ye Galstian, E.G. Len, S.V. Smolnik, M. Ya Shevchenko, T.D. Shatnii, Ye A. Tsapko, I.M. Makeieva, O. Yu Gerasymov

  • Open Access

    Effect of high energy laser processing on defect and structural phase state of titanium products made by additive technologies

    by Evgen Len, Iryna Galstian, Tobias Gustmann, Olexandr Gerasymov, Dmytro Savvakin, Vadim Bondarchuk, Denis Oryshych

    The microstructure, physical, and mechanical characteristics of 3D-printed metal products can be improved with high-energy heat treatment included in the manufacturing process. In the present study, Ti-6Al-4V titanium alloy products were 3D-printed with electron beam melting of wire of appropriate composition, while surface laser treatment of 3D-printed material was studied to determine the potential of microstructure modification and characteristics improvement. It was found that certain laser processing modes make it possible to eliminate micro defects (pores) in the samples that are harmful to structural materials. The obtained results also open the prospect of creating 3D-printed metal parts with specified profiles of physical and chemical properties, including gradients, as they model the change in material properties depending on the depth of the deposited layer during high-energy processing of each layer during its application. As demonstrated, both the condition of 3D printing as the velocity of deposition and thickness of each layer, the chemical composition and amount of impurities added to the matrix material during deposition, and the high-energy processing (heating or remelting) parameters are important to form the phase composition and mechanical properties of the final products. The high-energy processing also can be used to control the physicochemical properties of the product’s surface.

  • Open Access

    Effect of Caesium Adsorption on Emission Properties of (100) and (110) Surfaces of Tungsten and Molybdenum Single Crystals

    by Svyatoslav Smolnik, Iryna Galstian, Mykola Shevchenko, Tatiana Shatnii, Yevgen Tsapko, Olexandr Gerasymov, I. M. Makeeva, Sergij Mulenko, Evgen Len

    The paper examines the possibilities of using the electrode complex of the thermionic energy converter (TIC), which made from single crystals of the same type of refractory metals, but with different crystallographic orientations of the working surfaces of the cathode and anode. It solves the problem of evaporation of the cathode material at high operating temperatures and its deposition on the anode, and significantly extends the lifetime of the TIC. The dependences of the reflection coefficient of slow electrons and the electron work function on the concentration of caesium adsorbed on the (100) and (110) surfaces of molybdenum and tungsten single crystals have been studied by the methods of full-current spectroscopy and contact potential difference. As shown, the work function of both faces of the investigated single crystals of refractory metals changes nonmonotonically with an increase of the caesium concentration on the surfaces: at first, it decreases rapidly and reaches a minimum, and then, it smoothly increasing and reaches saturation. As found, due to the adjustment of the cathode and anode temperatures, which determine the concentration of caesium adsorbed on these electrodes, and due to the residual pressure of caesium vapor in the vacuum gap of the TIC, it is possible to satisfy the conditions for obtaining a significant power of the TIC, when the optimal difference in the values of the emitter and collector work function is realized (near 1–1.5 eV) with minimal reflection of electrons from the surface of the anode.


  • Open Access

    The Effect of Hydrogen Content on Electrophysical Properties of Hydrogenated Titanium – Thermally Expanded Graphite Composites

    by Iryna Galstian, H. Yu. Mykhailova, E. G. Len, M. M. Yakymchuk, V. A. Dekhtyarenko, J. Werner, T. D. Shatnii

    The nanocomposites based on metals with carbon nanostructures can be used as cathode materials for low temperature thermionic converters. Such materials often have different electrophysical properties from their original components. The peculiarities of the changes in electrical conductivity of powder composites containing thermally expanded graphite (TEG) and hydrogenated titanium before and after hydrogen desorption are investigated, and the influence of hydrogen on their properties is determined. The effect of conductivity growth is found at low TEG concentration in composites with both hydrogenated and dehydrogenated titanium. It can be explained by charge transfer from the metal to the TEG components of the composites. The effect of significant increase of composite conductivity after dehydrogenation can be explained by reduction of titanium oxide shell during hydrogen desorption from metal particle and by peculiarities of Fermi level shift in it during changes of electron concentration due to charge transfer to TEG.

  • Open Access

    Influence of multi-walled carbon nanotubes in polytetrafluoroethylene on the parameters of electronic structure and absorption of ultra-high-frequency radiation

    by I. Ye. Galstian, Ye. A. Tsapko, O. V. Makarenko, A. L. Yampolskiy, Ye. V. Tarusin, E. G. Len

    Using the methods of angular correlation of annihilation radiation (ACAR), attenuation of electromagnetic radiation in 1.5–2.2 GHz frequency range, and optical ellipsometry, it was shown that in composites of polytetrafluoroethylene (PTFE) + multi-walled carbon nanotubes (MWCNTs), a 2% decrease in the probability of annihilation of positrons in free volumes in PTFE leads to changes in other parameters of electronic structure of composites by 8–29%. Polytetrafluoroethylene is transparent to electromagnetic radiation, but after the addition of 10 wt.% or more of MWCNTs, the composites demonstrate 200–410-fold decrease in the electromagnetic radiation intensity when the radiation passes through a specimen with a thickness of ≈2 mm. It was found that the average radius of the free volumes and the probability of annihilation of positrons are determined by the defect and electronic structures of the polymer matrix only. The Fermi angle and the probability of positrons annihilation with free electrons are determined by the analogous structures of MWCNTs only. Since the electronic characteristics of the atoms and defects in the polymer matrix (at least outside the interphase) do not change, the changes in the other ACAR parameters are mainly due to changes in the imperfect MWCNTs’ atomic and electronic structures. The average radius of free volumes reaches its maximum value in the composite with 10 wt.% MWCNTs. It was found that in a specimen with 10 wt.% MWCNTs, the highest density of free electrons is observed due to charge transfer from free volumes to MWCNTs, and the highest electron density is observed on defects. A disorder of MWCNTs and their branched conductive network can form the ‘tails’ of electronic density of states in a band gap. Thus, composite with 10 wt.% MWCNTs has the highest absorption coefficient for electromagnetic radiation.


  • Open Access

    Emission Properties of Cathode Materials Based on LaNi$_5$–CNT Composites

    by I. M. Sydorchenko, N. A. Shevchenko, Ye. A. Tsapko, I. Ye. Galstan, H. Yu. Mykhaylova, E. G. Len


  • Generalized statistical dynamical theory of x-ray diffraction by imperfect multilayer crystal structures with defects

    by S. I. Olikhovskii, V. B. Molodkin, E. G. Len, E. S. Skakunova, S. V. Lizunova

    The generalized statistical dynamical theory of x-ray scattering by imperfect single crystals with randomly distributed Coulomb-type defects has been extended to characterize structure imperfections in the real multilayers of arbitrary thickness in Bragg diffraction geometry. The recurrence relations for the coherent amplitude reflection and transmission coefficients of such multilayers, which consist of any number of layers with constant strain and randomly distributed defects in each one, have been derived within the concept of the dynamical wave field, i.e., the so-called Ewald-Bethe-Laue approach, with rigorous accounting for boundary conditions at layer interfaces. The analytical expression for the differential dynamical diffuse component of the reflection coefficient of an imperfect multilayer system has been obtained as well. This expression establishes direct connection between the distribution of the diffuse scattering intensity in a momentum space and statistical characteristics of defects in each layer. In addition, the integrals from differential diffuse scattering intensity over the Ewald sphere and over vertical divergence have been found, which correspond to diffuse components in measurements of rocking curves and reciprocal space maps, respectively. The developed theory provides the dynamical description for the one- and two-dimensional angular distributions of the mutually consistent coherent and diffuse components of x-ray scattering intensities, which are measured by the high-resolution double- and triple-crystal diffractometers, respectively, from imperfect films, multilayer structures, superlattices, etc. Examples of simulated rocking curves for the imperfect superlattice with defects of several types and reciprocal space map for the ion-implanted sample of yttrium iron garnet film with defects are given and discussed.