Christina Stamos-Pfeiffer

Research and testing within the Air Force Research Laboratory at Edwards Air Force Base in the southwestern Mojave Desert has been conducted since the 1950s. This testing requires large quantities of groundwater for cooling and operations involving hazardous constituents that have entered the groundwater. To better understand the potential movement of contaminants through the groundwater system, the U.S. Geological Survey entered into a cooperative agreement with the U.S. Air Force Civil Engineer Center with the purpose of (1) gaining a more detailed understanding of the hydraulic connection between the unconsolidated basin-fill sediment and the underlying weathered and crystalline bedrock and (2) investigating faults and their potential effect on groundwater flow. This study was specific to the Arroyos subarea and Northeast Air Force Research Laboratory subarea of the Air Force Research Laboratory. The refined hydrogeologic characterization was derived by evaluating surface geologic maps, a regional gravity model, new subsurface geophysical surveys, lithology data from boreholes, and groundwater-level data.Refinement of the hydrogeologic characterization of the study area involved developing a map of basin-fill sediment thickness, estimating the geometry and depth to bedrock, determining the presence of weathered bedrock material, and identifying the location of faults and subsurface structures. The thickness of basin-fill sediment was derived from a regional gravity model. Basin-fill sediment ranges from less than 20 feet (ft) thick to about 150 ft thick and increases substantially toward a deep structural basin in the northwestern part of the study area. The top of bedrock estimated from the new surface geophysical surveys is generally deeper than the top of bedrock from the regional gravity model. These differences in interpreted bedrock tops indicate that there may be a zone of weathered bedrock in the subsurface, overlying crystalline bedrock. Additional subsurface data evaluating the geometry and thickness of weathered bedrock are necessary for a comprehensive evaluation of weathered bedrock in the study area. Previously unmapped extensions of the Leuhman Fault, Spring Fault Zone, and Boron Gate Fault were identified in the new surface geophysical surveys.Evaluation of groundwater flow between bedrock and basin-fill sediment, and the effects of faults on groundwater flow, was done using groundwater-level data from 2020. The groundwater table was in crystalline bedrock throughout most of the Arroyos and Northeast Air Force Research Laboratory subareas, with a few exceptions where it was in basin-fill sediment and weathered bedrock. Basin-fill sediment, and likely weathered bedrock, was partially saturated in parts of the study area where basin-fill sediment was as thick as 150 ft. Weathered bedrock material may be present near the Spring Fault Zone, and if so, was likely saturated in 2020. The groundwater-level data near and within Spring Fault Zone indicate that the Spring Fault Zone acts as a vertical-along-strike conduit for, and as an across-strike impediment to, groundwater flow. In addition, steep groundwater-level gradients in the southeastern part of the study area indicate that a subsurface structure affecting groundwater flow could be related to the Leuhman Fault. Sufficient groundwater-level data were not available to conclusively determine if the Arroyos, Rich, and Boron Gate Faults, and their inferred extensions from the geophysical surveys, affect the movement or direction of groundwater flow.

The relation between the groundwater and the amount of natural recharge to the Cahuilla Valley and Terwilliger Valley groundwater basins is not well understood. During the 20th century, the reliance on groundwater near Anza, California, used for agricultural, domestic, and municipal reasons has increased, and there is the potential for changes in groundwater availability related to climate change. Several types of existing data were evaluated, and new data were collected for this study, with the goal of characterizing the region’s hydrogeology. The study’s scope included constructing a geologic framework model to show where the groundwater-bearing units are present and their relation to each other, estimating the major components of the groundwater budget, and understanding local short-term and regional long-term groundwater flow and how that has changed since the early 1900s.Two electrical resistivity tomography surveys were done in the Durasno Valley about 2,150 feet apart to identify the thickness of the alluvium, its horizontal extent, and the depth-to-basement along two profiles perpendicular to Cahuilla Creek. The subsurface sediments were mostly horizontally layered and the transitional boundary between the alluvium and basement was thinner and shallower along the upgradient profile where the depth-to-basement was about 70 feet below land surface; the depth-to-basement at the downgradient profile was more than about 140 feet below land surface. The results from the surveys were used to place four monitoring wells at two sites along the survey profiles. Artesian flow from the deepest well at the downgradient site indicated that the decomposed and competent basement likely contributed some groundwater to the overlying alluvium, laterally, from below, or both.A digital three-dimensional geologic framework model was constructed using EarthVision software to represent the subsurface geometry of the alluvium, decomposed basement, and competent basement. Maps and cross sections of the modeled thicknesses of the alluvium and decomposed basement, and the modeled elevation of the top of the competent basement, were made to show the subsurface geometry of vertical faults, selected wells, and the groundwater-bearing units.Because natural recharge is related to the variable cycles of precipitation, estimates are difficult to quantify. Recharge and runoff have extreme interannual variability in the study area; recharge and runoff can be sporadic, and a substantive amount may not occur in some years. Estimates of recharge from a previous study and the regional-scale Basin Characterization Model for California for four different periods ranged from 3,800 acre-feet/year for 1897–1947 to 5,900 acre-feet/year for 1971–2000. Potential recharge from the disposal of domestic septic systems may have been as much as 500 acre-feet in 2020. It was estimated that between about 400 and 2,400 acre-feet/year of groundwater is lost through evapotranspiration by vegetation and evaporation from open water bodies, but the main source of discharge is through pumpage, mainly used for agriculture from the alluvium in the Cahuilla Valley and Terwilliger Valley groundwater basins. The estimated total pumpage for 1991–2021 ranged from about 1,140 acre-feet in 2019 to about 3,450 acre-feet in 1994. When summed, the cumulative amount of estimated pumpage between 1991 and 2021 was about 81,400 acre-feet.The general direction of groundwater flow is from the northeast along the San Jacinto fault zone at the headwaters of Cahuilla and Hamilton Creeks, to the surface-water outlets at the west and southeast parts of the study area. Groundwater-level data from the 1950s and earlier indicate that there was a natural groundwater divide between the Cahuilla Valley and Terwilliger Valley groundwater basins, but the changing magnitude and extent of the groundwater depressions caused by pumping since about 1950 indicate that the location of the natural groundwater boundary between the Cahuilla Valley and Terwilliger Valley groundwater basins has migrated over time.Flow from the upper to the lower parts of the Cahuilla Valley groundwater basin roughly follows the course of Cahuilla Creek through the narrow Durasno Valley where an estimated volume of flow in April 2019 was about 10–150 acre-feet/year. Short-term trends in groundwater levels, particularly in wells where groundwater is shallow and in the basement unit, show how some areas respond quickly to recharge and discharge. Wells located further to the east within the Cahuilla Valley groundwater basin in the alluvium show much less of a response to recharge events; areas of sustained pumpage from the alluvium, primarily for agriculture, show long-term declines in groundwater levels and generally do not show the effects of storm events or recent runoff. Groundwater levels in wells that are farthest from where most of the recharge occurs and where pumping has been the greatest, had some of the largest long-term groundwater-level declines at a rate of about 0.8 foot/year between 1971 and 2021.

Hydrologic and geophysical data were collected to support updates to an existing groundwater-flow model of Hinkley Valley, California, in the Mojave Desert about 80 miles northeast of Los Angeles, California. These data provide information on predevelopment (pre-1930) water levels, groundwater recharge, and selected hydrologic properties of aquifer materials.A predevelopment groundwater-level map, drawn using water-level measurements from 48 wells collected as early as 1918, showed groundwater movement from recharge areas along the Mojave River to evaporative discharge areas near the margin of Harper (dry) Lake in Water Valley. During predevelopment conditions, depth to water ranged from near land surface along the Mojave River to above land surface near Harper (dry) Lake, consistent with flowing wells in Water Valley at that time. Depths to water in much of Hinkley Valley downgradient from the Lockhart fault were less than 20 feet below land surface. By 2017, water-level declines as a result of agricultural pumping, were as much as 60 feet near the Hinkley compressor station.Areal recharge from infiltration of precipitation on the valley floor is negligible. Average annual recharge as infiltration of runoff from upland drainages to Hinkley and Water Valleys averages 64.7 acre-feet per year. In most years recharge does not occur; in years when it occurs, recharge to Hinkley Valley is typically about 296 acre-feet. In contrast, average recharge as infiltration of streamflow from the Mojave River from 1931 to 2015 was between 13,400 and 17,100 acre-feet per year; in some years recharge from the Mojave River exceeded 100,000 acre-ft. Estimates of predevelopment groundwater movement through Hinkley Gap and groundwater discharge to Harper (dry) Lake ranged from 570 to 1,900 and 820 to 2,460 acre-feet per year, respectively; at the time of this study in 2017, groundwater movement through Hinkley Gap was estimated to be about 83 acre-feet per year.Hydraulic-conductivity values estimated from slug-test data for 95 monitoring wells ranged from less than 0.1 to 680 feet per day (ft/d); values generally decreased with depth. Median hydraulic-conductivity values calculated from nuclear magnetic resonance (NMR) data for Mojave River alluvium and near-shore lake deposits were 73 and 11 ft/d, respectively; median hydraulic-conductivity values for locally derived alluvium and weathered bedrock were 6 and 2 ft/d, respectively. Hydraulic-conductivity values, estimated from NMR data for formerly saturated deposits overlying the 2017 water table, were as high as 300 ft/d near the Hinkley compressor station. Downgradient from the Hinkley compressor station, formerly saturated deposits had hydraulic-conductivity values of about 150 ft/d, which were higher than values in saturated material. Coarse-textured, permeable material in formerly saturated deposits above the 2017 water table may have allowed groundwater, released from the Hinkley compressor station that may have contained Cr(VI), to move rapidly downgradient.The Lockhart fault is an impediment to groundwater flow within Hinkley Valley. Groundwater-flow directions from horizontal point-velocity probe data were deflected to the west on the upgradient side of the fault compared to the nominal direction of groundwater flow estimated from water-level data. Younger groundwater was present on the upgradient and downgradient sides of the fault, and older groundwater with unadjusted carbon-14 ages as old as 5,650 years before present was in water from wells within splays of the Lockhart fault, consistent with limited groundwater movement across the fault. As a result, groundwater and Cr(VI) released from the Hinkley compressor station moved to the northwest along the downgradient side of the fault.Coupled well-bore flow and depth-dependent water-quality data show water from wells C-01 and IW-03 within the Q4 2015 (October–December 2015) regulatory Cr(VI) plume was yielded from thin layers within the aquifer that are composed of well-sorted lake-margin (beach) deposits that likely have high lateral and longitudinal connectivity. Collectively, data show highly permeable deposits above the regional water table and thin permeable deposits within saturated portions of the upper aquifer that may have conducted groundwater and Cr(VI) downgradient when releases from the Hinkley compressor station first occurred.

The Lucerne Valley is in the southwestern part of the Mojave Desert and is about 75 miles northeast of Los Angeles, California. The Lucerne Valley groundwater basin encompasses about 230 square miles and is separated from the Upper Mojave Valley groundwater basin by splays of the Helendale Fault. Since its settlement, groundwater has been the primary source of water for agricultural, industrial, municipal, and domestic uses. Groundwater withdrawal from pumping has exceeded the amount of water recharged to the basin, causing groundwater declines of more than 100 feet between 1917 and 2016 in the center of the basin. The continued withdrawal has resulted in an increase in pumping costs, reduced well efficiency, and land subsidence near Lucerne Lake. Although the volume of pumping has declined in recent years, there is concern that new agricultural growth and limits on imported water will continue to strain the sustainability of the groundwater system.To address these concerns, the U.S. Geological Survey entered into a cooperative agreement with the Mojave Water Agency to develop a better understanding of the Lucerne Valley hydrogeologic system and provide tools to help evaluate and manage the effects of future development in the Lucerne Valley. The objectives of this study were to (1) improve the understanding of the aquifer system, (2) improve the understanding of subsidence in the basin, and (3) incorporate the understanding into a groundwater-flow model that can be used to help manage the groundwater resources in the Lucerne Valley. The model developed for this study covers the period of 1942–2016 and can help evaluate various proposed water-management scenarios during different climatic and hydrologic conditions.The aquifer system consists of a shallow aquifer, a confining unit, and middle and lower aquifers. These layered water-bearing units were identified based on geologic units of the mostly unconsolidated sediments and hydrologic properties. These alluvial deposits consist of clay, silt, sand, and gravel; some places also contain clay and silty clay lacustrine deposits. Several faults act, at least in part, as barriers to groundwater flow on the eastern, southern, and western edges of the basin. Present-day natural recharge is primarily from the infiltration of runoff from the San Bernardino Mountains to the south; however, stable and radioactive isotopes show that groundwater from the middle of the Lucerne Valley was older than about 10,000 years and probably was recharged as infiltration from streams draining the mountains in the Mojave Desert to the north, which probably does not occur under present-day climatic conditions. The annual average natural recharge for 1942–2016, estimated by a Basin Characterization Model, was about 635 acre-feet per year; the average amount of treated wastewater effluent transferred to the Lucerne Valley for artificial recharge annually ranged from about 1,500 to 4,000 acre-feet per year during 1980–2016. Pumpage estimates for 1942–2016 ranged from about 3,000 acre-feet in 1942 to about 18,300 acre-feet in 1984. The total cumulative amount of groundwater removed from the basin by pumping between 1942 and 2016 was estimated to be about 700,000 acre-feet, which was about 10 times greater than the cumulative amount of recharge to the entire Lucerne Valley groundwater basin. Before groundwater development, the direction of groundwater flow was from the southern part of the basin northward to discharge areas near Lucerne Lake, where it discharged through springs along the Helendale Fault and by evapotranspiration. Since the early 1900s, groundwater-level declines have mostly eliminated the areas where natural discharge occurred and exceeded 100 feet in the middle of the basin between the early 1950s and mid-1990s, and as much as 25 feet near the margins from about the mid-1950s to 2000s. A decrease in the rate of pumping after the mid-1990s lessened the hydraulic stress on the middle and lower aquifers and enabled hydraulic heads in the middle of the basin to recover slightly as groundwater near the margins of the basin moved toward the pumping depression. Although trends in groundwater levels in the center of the basin have reversed since the mid-1990s, levels at the basin margins continue to decline as the movement of groundwater from the margins fills the pumping depression and gradually flattens the groundwater table throughout the basin.The long-term extraction of groundwater and associated dewatering of the fine-grained sediments present within the aquifer system has resulted in aquifer compaction and consequently land subsidence, primarily near Lucerne Lake. Analysis of interferometric synthetic aperture radar data shows that almost 11 inches of land subsidence has occurred south of Lucerne Lake between April 1992 and November 2009; less subsidence occurred elsewhere in the basin during this period. This differential land subsidence has caused fissures and cracks in the ground surface, which have buckled the pavement and undercut roads in several locations.The Lucerne Valley Hydrologic Model was developed using the finite-difference groundwater modeling software One Water Hydrologic Model to represent the hydrologic conditions and stresses during 1942–2016. The model has a uniform grid of approximately 92 acres per cell (2,000 feet by 2,000 feet) and has four layers representing the water-bearing units. The results from the calibrated model simulations indicated that groundwater pumpage exceeded recharge, resulting in an estimated net cumulative depletion of groundwater storage (discharge minus recharge) of about 465,000 acre-feet from 1942 to 2016. The model simulated as much as 7.5 feet (90 inches; 2,286 millimeters) of aquifer compaction, which indicates the extensive fine-grained deposits and measured subsidence near Lucerne Lake.

First posted February 10, 2022 Director, California Water Science Center U.S. Geological Survey 6000 J Street, Placer Hall Sacramento, California 95819 Water management in the Santa Ana River watershed in San Bernardino and Riverside Counties in southern California (fig. A1) is complex with various water purveyors navigating geographic, geologic, hydrologic, and political challenges to provide a reliable water supply to stakeholders. As the population has increased throughout southern California, so has the demand for water. The Yucaipa groundwater subbasin (hereafter referred to as “Yucaipa subbasin”), one of nine groundwater subbasins in what the California Department of Water Resources (DWR) refers to as the Upper Santa Ana Valley groundwater basin (California Department of Water Resources, 2016; fig. A1; the DWR naming convention is used within this report), is no exception; steady population growth since the 1940s and changes in water use have forced local water purveyors to regularly adapt their water infrastructure. Water demands within the Yucaipa subbasin have historically been supplied by groundwater, but water imported via the California State Water Project has augmented the total water supply through direct use and through anthropogenic recharge at the Wilson Creek and Oak Glen Creek spreading basins since 2002. Overall demand for groundwater continues to rise, and local water managers are concerned that despite the influx of imported water, groundwater levels may decline to a point where producing water will be uneconomical, severely limiting the ability of local agencies to meet water-supply demand. To better understand the hydrogeology and water resources in the Yucaipa subbasin, the U.S. Geological Survey (USGS) initiated a study in cooperation with the San Bernardino Valley Municipal Water District (SBVMWD) to characterize and model the hydrologic system of the Yucaipa subbasin and the surrounding Yucaipa Valley watershed (YVW; fig. A2). To gain this comprehensive understanding, a three-dimensional (3D) hydrogeologic framework model (HFM; Cromwell and Matti, 2022) was constructed to quantify the structure and extent of hydrogeologic units in the YVW; the hydrologic system was conceptualized and quantified (described in chapter A); and the Yucaipa Integrated Hydrological Model (YIHM; described in chapter B) was developed to simulate the integrated surface-water and aquifer systems, including natural and anthropogenic recharge and discharge throughout the study area during 1947–2014.

The San Antonio Creek Valley watershed (SACVW) is located in western Santa Barbara County, about 15 miles south of Santa Maria and 55 miles north of Santa Barbara, California. The SACVW is about 135 square miles and encompasses the San Antonio Creek Valley groundwater basin; the SACVW is separated from adjacent groundwater basins by the Casmalia and Solomon Hills to the north, and the Purisima Hills to the south. At the western, downstream part of the valley, uplifted, consolidated rocks cause groundwater to discharge at land surface at Barka Slough. Since the late 1800s, groundwater has been the primary source of water for agricultural, military, municipal, and domestic uses. Groundwater withdrawal by pumping exceeded the amount of water replenishing the aquifer system during water years 1948–2018, causing groundwater-level declines of more than 150 feet in parts of the valley and reducing base flow at Barka Slough. Reliance on groundwater for agricultural water use (primarily for the irrigation and frost protection of vineyards, and fruit and berry crops) continues to strain the sustainability of the groundwater system.Through a cooperative agreement, the Santa Barbara County Water Agency and Vandenberg Space Force Base invited the U.S. Geological Survey to address declines in groundwater levels, develop a better understanding of the hydrogeologic system, and provide tools to help evaluate and manage the effects of future development of the San Antonio Creek Valley groundwater basin within the encompassing San Antonio Creek Valley watershed (SACVW). The objectives of this study were to (1) refine the hydrogeologic framework of the San Antonio Creek Valley watershed, (2) quantify the hydrologic budget of the valley, and (3) develop hydrologic modeling tools to evaluate and aid in managing the groundwater resource. This report focuses on the first and second objectives to construct a hydrogeologic framework and characterize the historical and present-day hydrologic conditions of the SACVW during water years 1948–2018. As part of the second objective, work included quantifying the hydrologic budget and evaluating the hydrogeologic system using a combination of existing data and geologic and hydrologic data collected for this study.The groundwater-flow system in the SACVW consists of five hydrogeologic units. These separate water-bearing units were identified based on hydrogeologic properties, such as sediment grain size, vertical-head differences in multiple-depth, monitoring-well sites, long-term groundwater level responses to pumping and climate, and the chemical character of groundwater and groundwater age in the mostly semi-consolidated to unconsolidated basin-fill sediments. The hydrogeologic units that comprise the different aquifers vary in their lithologic composition. The upper and lower aquifers (upper Paso Robles Formation, and lower Paso Robles Formation and Careaga Sandstone, respectively) are relatively coarse grained and are comprised of sand, gravel, and clay; the middle confining unit (the middle Paso Robles Formation) is relatively fine grained and is comprised of primarily clay, silt, and sand. The Pezzoni-Casmalia and Los Alamos faults, which are inferred to transect the SACVW between the western and eastern areas of the valley floor, do not appear to substantially affect the groundwater system.Present-day recharge to the study area occurs primarily as infiltration from precipitation and streams in the upland areas of the Casmalia Hills and Solomon Hills, and along the main channel of San Antonio Creek. Reported estimates of annual natural recharge during water years 1948–2018 generally ranged from about 5,000 acre-feet to more than about 30,000 acre-feet. Stable and radioactive isotopes show that groundwater from the lower aquifer is old and probably was recharged as infiltration from precipitation and streams in the eastern upland areas of the Solomon Hills; however, the infiltration and recharge from these sources probably does not occur under present-day climatic conditions. Anthropogenic recharge, from sources such as return flow from agricultural irrigation, municipal water systems, and wastewater effluent, was estimated to range from about 600 acre-feet in 1948 to about 6,600 acre-feet in 2018. The average annual amount of groundwater removed from the SACVW by pumping during 1948–2018 was estimated to be about 17,200 acre-feet per year, increasing from about 3,000 acre-feet in 1948 to about 32,600 acre-feet in 2018. Estimates of annual pumpage generally exceeded estimates of annual recharge beginning in the mid-1970s and continuing through 2018. The predominant direction of groundwater flow under historical and present-day conditions was from the eastern uplands in the Solomon Hills to the west along San Antonio Creek to the discharge area in Barka Slough, and from the northern uplands in the Casmalia Hills south to San Antonio Creek.Pumpage since the early 1900s and the subsequent groundwater-level declines have substantially reduced the amount of natural groundwater discharge at Barka Slough. Estimates of base flow to San Antonio Creek at the western, downstream extent of the SACVW have varied over time in response to changes in groundwater pumpage and climate; however, there was an overall decline in base flow during water years 1956–2018, decreasing from an average of about 1,700 acre-feet per year during 1956–69, to about 300 acre-feet per year during 2016–18. The long-term extraction of groundwater correlates with a decrease in groundwater levels by more than about 150 feet since the early 1940s in the eastern part of the basin near Los Alamos, and as much as about 50 feet in the upland areas and in the western part of the basin. At Barka Slough, groundwater levels have declined below land surface in some places, altering native riparian vegetation in and around the slough.Surface-water quality in the SACVW...

First posted July 19, 2017 California Water Science Center U.S. Geological Survey 6000 J Street, Placer Hall Sacramento, California 95819 The increasing demands on groundwater for water supply in desert areas in California and the western United States have resulted in the need to better understand groundwater sources, availability, and sustainability. This is true for a 650-square-mile area that encompasses the Antelope Valley, El Mirage Valley, and Upper Mojave River Valley groundwater basins, about 50 miles northeast of Los Angeles, California, in the western part of the Mojave Desert. These basins have been adjudicated to ensure that groundwater rights are allocated according to legal judgments. In an effort to assess if the boundary between the Antelope Valley and El Mirage Valley groundwater basins could be better defined, the U.S. Geological Survey began a cooperative study in 2014 with the Mojave Water Agency to better understand the hydrogeology in the area and investigate potential controls on groundwater flow and availability, including basement topography. Recharge is sporadic and primarily from small ephemeral washes and streams that originate in the San Gabriel Mountains to the south; estimates range from about 400 to 1,940 acre-feet per year. Lateral underflow from adjacent basins has been considered minor in previous studies; underflow from the Antelope Valley to the El Mirage Valley groundwater basin has been estimated to be between 100 and 1,900 acre-feet per year. Groundwater discharge is primarily from pumping, mostly by municipal supply wells. Between October 2013 and September 2014, the municipal pumpage in the Antelope Valley and El Mirage Valley groundwater basins was reported to be about 800 and 2,080 acre-feet, respectively. This study was motivated by the results from a previously completed regional gravity study, which suggested a northeast-trending subsurface basement ridge and saddle approximately 3.5 miles west of the boundary between the Antelope Valley and El Mirage Valley groundwater basins that might influence groundwater flow. To better define potential basement structures that could affect groundwater flow between the groundwater basins in the study area, gravity data were collected using more closely spaced measurements in September 2014. Groundwater-level data was gathered and collected from March 2014 through March 2015 to determine depth to water and direction of groundwater flow. The gravity and groundwater-level data showed that the saturated thickness of the alluvium was about 2,000 feet thick to the east and about 130 feet thick above the northward-trending basement ridge near Llano, California. Although it was uncertain whether the basement ridge affects the groundwater system, a potential barrier to groundwater flow could be created if the water table fell below the altitude of the basement ridge, effectively causing the area to the west of the basement ridge to become hydraulically isolated from the area to the east. In addition, the direction of regional-groundwater flow likely will be influenced by future changes in the number and distribution of pumping wells and the thickness of the saturated alluvium from which water is withdrawn. Three-dimensional animations were created to help visualize the relation between the basins’ basement topography and the groundwater system in the area. Further studies that could help to more accurately define the basins and evaluate the groundwater-flow system include exploratory drilling of multi-depth monitoring wells; collection of depth-dependent water-quality samples; and linking together existing, but separate, groundwater-flow models from the Antelope Valley and El Mirage Valley groundwater basins into a single, calibrated groundwater-flow model.

The Borrego Valley is a small valley (110 square miles) in the northeastern part of San Diego County, California. Although the valley is about 60 miles northeast of city of San Diego, it is separated from the Pacific Ocean coast by the mountains to the west and is mostly within the boundaries of Anza-Borrego Desert State Park. From the time the basin was first settled, groundwater has been the only source of water to the valley. Groundwater is used for agricultural, recreational, and municipal purposes. Over time, groundwater withdrawal through pumping has exceeded the amount of water that has been replenished, causing groundwater-level declines of more than 100 feet in some parts of the basin. Continued pumping has resulted in an increase in pumping lifts, reduced well efficiency, dry wells, changes in water quality, and loss of natural groundwater discharge. As a result, the U.S. Geological Survey began a cooperative study of the Borrego Valley with the Borrego Water District (BWD) in 2009. The purpose of the study was to develop a greater understanding of the hydrogeology of the Borrego Valley Groundwater Basin (BVGB) and to provide tools to help evaluate the potential hydrologic effects of future development. The objectives of the study were to (1) improve the understanding of groundwater conditions and land subsidence, (2) incorporate this improved understanding into a model that would assist in the management of the groundwater resources in the Borrego Valley, and (3) use this model to test several management scenarios. This model provides the capability for the BWD and regional stakeholders to quantify the relative benefits of various options for increasing groundwater storage. The study focuses on the period 1945–2010, with scenarios 50 years into the future. This report documents and presents (1) an analysis of the conceptual model, (2) a description of the hydrologic features, (3) a compilation and analysis of water-quality data, (4) the measurement and analysis of land subsidence by using geophysical and remote sensing techniques, (5) the development and calibration of a two-dimensional borehole-groundwater-flow model to estimate aquifer hydraulic conductivities, (6) the development and calibration of a three-dimensional (3-D) integrated hydrologic flow model, (7) a water-availability analysis with respect to current climate variability and land use, and (8) potential future management scenarios. The integrated hydrologic model, referred to here as the “Borrego Valley Hydrologic Model” (BVHM), is a tool that can provide results with the accuracy needed for making water-management decisions, although potential future refinements and enhancements could further improve the level of spatial and temporal resolution and model accuracy. Because the model incorporates time-varying inflows and outflows, this tool can be used to evaluate the effects of temporal changes in recharge and pumping and to compare the relative effects of different water-management scenarios on the aquifer system. Overall, the development of the hydrogeologic and hydrologic models, data networks, and hydrologic analysis provides a basis for assessing surface and groundwater availability and potential water-resource management guidelines.