Enrico Sangiorgi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Enrico Sangiorgi has a total of 46 co-authors. Here are the top co-authors by number of shared publications:
- Andrea Natale Tallarico
Department of Electrical, Electronic, and Information Engineering, Advanced Research Center on Electronic System, University of Bologna, Cesena, Italy
7 shared publications - Stefaan Decoutere
IMEC, 3001 Leuven, Belgium
5 shared publications - Benoit Bakeroot
IMEC, Leuven, Belgium
4 shared publications C. Fiegna
Department of Electrical, Electronic and Information Engineering, Advanced Research Center on Electronic System, University of Bologna, Cesena, Italy
4 shared publications- Marco Tartagni
Advanced Research Center on Electronic Systems (ARCES), University of Bologna, Cesena Campus, Cesena, Italy
4 shared publications - Niels Posthuma
IMEC, Leuven, Belgium
4 shared publications
Latest Publications
- Open Access
- 8 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 45 (9) , 1630-1633
P-GaN Gate HEMTs: A Solution to Improve the High-Temperature Gate Lifetime
In this letter, we report an approach to improve the forward bias gate reliability of Schottky gate p-GaN HEMTs. In particular, a gate layout solution, namely Gate Within Active Area (GWA), aimed at improving the high-temperature time to failure (TTF), is proposed and validated. This solution allows to avoid the exposure of the gate finger (p-GaN/metal) to the nitrogen-implantation needed for termination and isolation purposes. GWA devices feature a significantly improved gate reliability at high temperature with respect to the reference ones, under both DC and pulsed stress tests. Finally, it is demonstrated that the Schottky gate p-GaN HEMTs show a positive temperature-dependent gate TTF in a range up to $150~^{\circ }$ C, confirming the crucial role of impact ionization on the gate failure.
- 8 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 45 (9) , 1630-1633
Open AccessP-GaN Gate HEMTs: A Solution to Improve the High-Temperature Gate Lifetime
In this letter, we report an approach to improve the forward bias gate reliability of Schottky gate p-GaN HEMTs. In particular, a gate layout solution, namely Gate Within Active Area (GWA), aimed at improving the high-temperature time to failure (TTF), is proposed and validated. This solution allows to avoid the exposure of the gate finger (p-GaN/metal) to the nitrogen-implantation needed for termination and isolation purposes. GWA devices feature a significantly improved gate reliability at high temperature with respect to the reference ones, under both DC and pulsed stress tests. Finally, it is demonstrated that the Schottky gate p-GaN HEMTs show a positive temperature-dependent gate TTF in a range up to $150~^{\circ }$ C, confirming the crucial role of impact ionization on the gate failure.
- Open Access
- 30 June 2024
- Published by MDPI AG in Micromachines
- Vol. 15 (7) , 872
Positive Bias Temperature Instability in SiC-Based Power MOSFETs
This paper investigates the threshold voltage shift (ΔVTH) induced by positive bias temperature instability (PBTI) in silicon carbide (SiC) power MOSFETs. By analyzing ΔVTH under various gate stress voltages (VGstress) at 150 °C, distinct mechanisms are revealed: (i) trapping in the interface and/or border pre-existing defects and (ii) the creation of oxide defects and/or trapping in spatially deeper oxide states with an activation energy of ~80 meV. Notably, the adoption of different characterization methods highlights the distinct roles of these mechanisms. Moreover, the study demonstrates consistent behavior in permanent ΔVTH degradation across VGstress levels using a power law model. Overall, these findings deepen the understanding of PBTI in SiC MOSFETs, providing insights for reliability optimization.
- 30 June 2024
- Published by MDPI AG in Micromachines
- Vol. 15 (7) , 872
Open AccessPositive Bias Temperature Instability in SiC-Based Power MOSFETs
This paper investigates the threshold voltage shift (ΔVTH) induced by positive bias temperature instability (PBTI) in silicon carbide (SiC) power MOSFETs. By analyzing ΔVTH under various gate stress voltages (VGstress) at 150 °C, distinct mechanisms are revealed: (i) trapping in the interface and/or border pre-existing defects and (ii) the creation of oxide defects and/or trapping in spatially deeper oxide states with an activation energy of ~80 meV. Notably, the adoption of different characterization methods highlights the distinct roles of these mechanisms. Moreover, the study demonstrates consistent behavior in permanent ΔVTH degradation across VGstress levels using a power law model. Overall, these findings deepen the understanding of PBTI in SiC MOSFETs, providing insights for reliability optimization.
- Open Access
- 20 February 2023
- Published by MDPI AG in Electronics
- Vol. 12 (4) , 1063
A Reconfigurable Setup for the On-Wafer Characterization of the Dynamic RON of 600 V GaN Switches at Variable Operating Regimes
Charge-trapping mechanisms observed in high-voltage GaN switches are responsible for the degradation of power converter efficiency due to modulation of the effective dynamic ON-resistance () with respect to its static value. Dynamic degradation is typically dependent on the blocking voltage and the commutation frequency and is particularly significant in new technologies under development. The possibility to characterize this phenomenon on GaN switch samples directly on-wafer, under controlled operating conditions that resemble real operations of the DUT in a switching mode power converter is extremely valuable in the development phase of new technologies or for quality verification of production wafers. In this paper, we describe a setup that allows this characterization: dynamic degradation of on-wafer 600 V GaN switches is characterized as a function of the blocking voltage, the driving voltage, and at different temperatures. The dependency on the switching frequency is identified by measuring the current recovery of the switch after the application of blocking voltages of different durations.- 20 February 2023
- Published by MDPI AG in Electronics
- Vol. 12 (4) , 1063
Open AccessA Reconfigurable Setup for the On-Wafer Characterization of the Dynamic RON of 600 V GaN Switches at Variable Operating Regimes
Charge-trapping mechanisms observed in high-voltage GaN switches are responsible for the degradation of power converter efficiency due to modulation of the effective dynamic ON-resistance () with respect to its static value. Dynamic degradation is typically dependent on the blocking voltage and the commutation frequency and is particularly significant in new technologies under development. The possibility to characterize this phenomenon on GaN switch samples directly on-wafer, under controlled operating conditions that resemble real operations of the DUT in a switching mode power converter is extremely valuable in the development phase of new technologies or for quality verification of production wafers. In this paper, we describe a setup that allows this characterization: dynamic degradation of on-wafer 600 V GaN switches is characterized as a function of the blocking voltage, the driving voltage, and at different temperatures. The dependency on the switching frequency is identified by measuring the current recovery of the switch after the application of blocking voltages of different durations. - Open Access
- 13 February 2023
- Published by MDPI AG in Electronics
- Vol. 12 (4) , 943
Characterization of the Dynamic RON of 600 V GaN Switches under Operating Conditions
High-voltage GaN switches can offer tremendous advantages over silicon counterparts for the development of high-efficiency switching-mode power converters at high commutation frequency. Nonetheless, GaN devices are prone to charge-trapping effects that can be particularly relevant in the early-stage development of new technologies. Charge-trapping mechanisms are responsible for the degradation of the dynamic ON-resistance () with respect to its static value: this degradation is typically dependent on the blocking voltage, the commutation frequency and temperature, and is responsible for the reduction of power converter efficiency. The characterization of this phenomenon is very valuable for the development of a new process to compare different technological solutions or for the final assessment of performance. This characterization cannot be made with traditional static or small signal measurements since degradation is triggered by application-like dynamic device excitations. In this paper, we propose a technique for the characterization of the dynamic of high-voltage GaN switches under real operating conditions: this technique is based on the design of a half bridge switching leg in which the DUT is operated under conditions that resemble its operation in a power converter. With this setup, the characterization of a 600 V GaN switch dynamic is performed as a function of variable blocking voltages and commutation frequency. Additionally, this technique allows the separation of thermal and trapping effects, enabling the characterization of the dynamic at different temperatures.- 13 February 2023
- Published by MDPI AG in Electronics
- Vol. 12 (4) , 943
Open AccessCharacterization of the Dynamic RON of 600 V GaN Switches under Operating Conditions
High-voltage GaN switches can offer tremendous advantages over silicon counterparts for the development of high-efficiency switching-mode power converters at high commutation frequency. Nonetheless, GaN devices are prone to charge-trapping effects that can be particularly relevant in the early-stage development of new technologies. Charge-trapping mechanisms are responsible for the degradation of the dynamic ON-resistance () with respect to its static value: this degradation is typically dependent on the blocking voltage, the commutation frequency and temperature, and is responsible for the reduction of power converter efficiency. The characterization of this phenomenon is very valuable for the development of a new process to compare different technological solutions or for the final assessment of performance. This characterization cannot be made with traditional static or small signal measurements since degradation is triggered by application-like dynamic device excitations. In this paper, we propose a technique for the characterization of the dynamic of high-voltage GaN switches under real operating conditions: this technique is based on the design of a half bridge switching leg in which the DUT is operated under conditions that resemble its operation in a power converter. With this setup, the characterization of a 600 V GaN switch dynamic is performed as a function of variable blocking voltages and commutation frequency. Additionally, this technique allows the separation of thermal and trapping effects, enabling the characterization of the dynamic at different temperatures. - 14 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 43 (11) , 1846-1849
The Role of Frequency and Duty Cycle on the Gate Reliability of p-GaN HEMTs
In this letter, we present an extensive analysis on the role of both switching frequency (ranging from 100 kHz to 1 MHz) and duty cycle (from 10% to 90%) on the time-dependent gate breakdown of high electron mobility transistors (HEMTs) with Schottky metal to p-GaN gate. More specifically, results show how the gate lifetime of GaN HEMTs increases by reducing the frequency and the duty cycle of the stressing gate signal (V G ). Such behavior is ascribed to the OFF-time, which is responsible to alter the electrostatic potential in the p-GaN layer during the rising phases of V G (from OFF- to ON-state). Findings of this analysis are useful both for further technology improvement and for GaN-based power circuit designers.
- 14 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 43 (11) , 1846-1849
The Role of Frequency and Duty Cycle on the Gate Reliability of p-GaN HEMTs
In this letter, we present an extensive analysis on the role of both switching frequency (ranging from 100 kHz to 1 MHz) and duty cycle (from 10% to 90%) on the time-dependent gate breakdown of high electron mobility transistors (HEMTs) with Schottky metal to p-GaN gate. More specifically, results show how the gate lifetime of GaN HEMTs increases by reducing the frequency and the duty cycle of the stressing gate signal (V G ). Such behavior is ascribed to the OFF-time, which is responsible to alter the electrostatic potential in the p-GaN layer during the rising phases of V G (from OFF- to ON-state). Findings of this analysis are useful both for further technology improvement and for GaN-based power circuit designers.
- Open Access
- 16 February 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 10, 1-2
Editorial
I Would like to express my sincere gratitude – and the gratitude of the Electron Device Society (EDS) community at large – to Colin McAndrew , A. G. Unil Perera , and Krishna Shenai , for their commitment, dedication, and hard work during their nine plus years of service on the Journal of the Electron Devices editorial board. They were part of the initial team that launched J-EDS and made it the internationally renowned, open access, vibrant publication of these days. I will miss their knowledge, wisdom, and responsiveness! Our very best wishes to them in their future endeavors.
- 16 February 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 10, 1-2
Open AccessEditorial
I Would like to express my sincere gratitude – and the gratitude of the Electron Device Society (EDS) community at large – to Colin McAndrew , A. G. Unil Perera , and Krishna Shenai , for their commitment, dedication, and hard work during their nine plus years of service on the Journal of the Electron Devices editorial board. They were part of the initial team that launched J-EDS and made it the internationally renowned, open access, vibrant publication of these days. I will miss their knowledge, wisdom, and responsiveness! Our very best wishes to them in their future endeavors.
- 23 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 69 (2) , 507-513
TCAD Modeling of the Dynamic V TH Hysteresis Under Fast Sweeping Characterization in p-GaN Gate HEMTs
TCAD modeling of the dynamic threshold voltage shift (hysteresis) occurring under fast sweeping characterization in Schottky-type p-GaN gate high-electron-mobility transistors (HEMTs) is reported, to the best of our knowledge, for the first time. Dynamic ${V}_{\text{TH}}$ hysteresis has been first experimentally characterized under different sweeping times, temperatures, and AlGaN barrier configurations. Then, TCAD simulations have been carried out, reproducing the experimental evidences and understanding the microscopic mechanisms responsible for such effect. In particular, nonlocal tunneling models implemented in Sentaurus TCAD, defined at the gate Schottky contact and assisted by traps in the AlGaN barrier layer, have been adopted and properly tuned against experiments. Results show that the dynamic ${V}_{\text{TH}}$ hysteresis is mainly caused by the time-dependent hole charging/discharging processes in the floating p-GaN layer, which are governed by the Schottky and AlGaN barrier leakage current components.
- 23 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 69 (2) , 507-513
TCAD Modeling of the Dynamic V TH Hysteresis Under Fast Sweeping Characterization in p-GaN Gate HEMTs
TCAD modeling of the dynamic threshold voltage shift (hysteresis) occurring under fast sweeping characterization in Schottky-type p-GaN gate high-electron-mobility transistors (HEMTs) is reported, to the best of our knowledge, for the first time. Dynamic ${V}_{\text{TH}}$ hysteresis has been first experimentally characterized under different sweeping times, temperatures, and AlGaN barrier configurations. Then, TCAD simulations have been carried out, reproducing the experimental evidences and understanding the microscopic mechanisms responsible for such effect. In particular, nonlocal tunneling models implemented in Sentaurus TCAD, defined at the gate Schottky contact and assisted by traps in the AlGaN barrier layer, have been adopted and properly tuned against experiments. Results show that the dynamic ${V}_{\text{TH}}$ hysteresis is mainly caused by the time-dependent hole charging/discharging processes in the floating p-GaN layer, which are governed by the Schottky and AlGaN barrier leakage current components.
- Open Access
- 10 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 9, 1297
Editorial
The Journal of Electron Devices Society (J-EDS), founded in 2013, has continued along its track of consolidated scientific reputation during 2021.
- 10 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 9, 1297
Open AccessEditorial
The Journal of Electron Devices Society (J-EDS), founded in 2013, has continued along its track of consolidated scientific reputation during 2021.
- Open Access
- 22 April 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 9, 429-430
Quality in Simulation-Only Manuscripts Submitted to J-EDS
In recent years the Journal of the Electron Device Society (J-EDS) has experienced an increasing number of submissions of “simulation only” manuscripts. One reason for this is the improved accuracy and maturity of physicsbased simulation tools, either Technology Computer Aided Design (TCAD) or circuit analysis programs, that allow researchers to explore, devise and optimize the best breakthroughs going beyond the state-of-the-art technology without the need for experimental validation.
- 22 April 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 9, 429-430
Open AccessQuality in Simulation-Only Manuscripts Submitted to J-EDS
In recent years the Journal of the Electron Device Society (J-EDS) has experienced an increasing number of submissions of “simulation only” manuscripts. One reason for this is the improved accuracy and maturity of physicsbased simulation tools, either Technology Computer Aided Design (TCAD) or circuit analysis programs, that allow researchers to explore, devise and optimize the best breakthroughs going beyond the state-of-the-art technology without the need for experimental validation.
- Open Access
- 22 February 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 9, 1
Editorial
I would like to express my sincere gratitude—and the gratitude of the Electron Device Society (EDS) community at large—to David Abe and Tian-Ling Ren, for their commitment, dedication and hard work during their six years of service on the Journal of Electron Devices editorial board. Our very best wishes to them in their future endeavors.
- 22 February 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 9, 1
Open AccessEditorial
I would like to express my sincere gratitude—and the gratitude of the Electron Device Society (EDS) community at large—to David Abe and Tian-Ling Ren, for their commitment, dedication and hard work during their six years of service on the Journal of Electron Devices editorial board. Our very best wishes to them in their future endeavors.