Lawrence T. Clark
Research Subjects
Research Interests
Lawrence T. Clark has a total of 82 co-authors. Here are the top co-authors by number of shared publications:
- Keith E. Holbert
School of Electrical, Computer and Energy Engineering, Arizona State University, Tempe, AZ, USA
7 shared publications - Vinay Vashishtha
School of Electrical, Computer and Energy Engineering, Arizona State University, Tempe, AZ, USA
5 shared publications - Hugh J. Barnaby
School of Electrical, Computer, and Energy Engineering, Arizona State University, Tempe, AZ, USA
4 shared publications John Brunhaver
School of Electrical, Computer and Energy Engineering, Arizona State University, Tempe, AZ, USA
4 shared publications- Matthew J. Marinella
Arizona State University, Tempe, AZ, USA
4 shared publications Aditya Gujja
School of Electrical, Computer and Energy Engineering, Arizona State University, Tempe, AZ, USA
3 shared publications
Latest Publications
- 10 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 70 (8) , 2034-2041
Total Ionizing Dose Response of a 22-nm Compiled Fully Depleted Silicon-on-Insulator Static Random Access Memory
The results of total ionizing dose (TID) experiments on fully-depleted silicon-on-insulator (FDSOI) static random access memory (SRAM) are presented. Using 60 Co gamma irradiation, tests were conducted at multiple voltages and with and without read and write assists. The results demonstrate cell stability past 200 krad(Si) TID in standard operational modes. The impact of read and write assists and read timing via margin mode tests are examined. We also report input-output (IO) level translation circuit failures, as well as anomalous circuit failures attributable to IO at relatively low TID dose. Finally, we show post-TID anneal and low voltage SRAM results.
- 10 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 70 (8) , 2034-2041
Total Ionizing Dose Response of a 22-nm Compiled Fully Depleted Silicon-on-Insulator Static Random Access Memory
The results of total ionizing dose (TID) experiments on fully-depleted silicon-on-insulator (FDSOI) static random access memory (SRAM) are presented. Using 60 Co gamma irradiation, tests were conducted at multiple voltages and with and without read and write assists. The results demonstrate cell stability past 200 krad(Si) TID in standard operational modes. The impact of read and write assists and read timing via margin mode tests are examined. We also report input-output (IO) level translation circuit failures, as well as anomalous circuit failures attributable to IO at relatively low TID dose. Finally, we show post-TID anneal and low voltage SRAM results.
- 10 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 23 (1) , 162-171
Extracting Total Ionizing Dose Threshold Voltage Shifts From Ring Oscillator Circuit Response
Total ionizing dose (TID) has a significant effect on silicon on insulator circuits, manifest primarily as a front gate threshold voltage (Vt) shift. This paper presents a simple ring oscillator (RO) test structure that is amenable to packaging and gamma irradiation. RO current and frequency changes due to TID are experimentally measured in-situ. The RO responses are then used to extract the transistor level Vt shifts using an optimization approach. Since the optimization uses the actual circuits, the resulting Vt shifts may be directly applied to post TID modeling of circuit behavior. The approach simplifies the effort for design and testing to determine TID degradation. The test chip fabricated and measured for this work is implemented on a 22 nm fully depleted silicon on insulator (FDSOI) with thin oxides. The approach is, however, applicable to any fabrication process. Finally, we show the extracted Vt changes due to TID vary with the transistor Vt (doping and well type).
- 10 February 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Device and Materials Reliability
- Vol. 23 (1) , 162-171
Extracting Total Ionizing Dose Threshold Voltage Shifts From Ring Oscillator Circuit Response
Total ionizing dose (TID) has a significant effect on silicon on insulator circuits, manifest primarily as a front gate threshold voltage (Vt) shift. This paper presents a simple ring oscillator (RO) test structure that is amenable to packaging and gamma irradiation. RO current and frequency changes due to TID are experimentally measured in-situ. The RO responses are then used to extract the transistor level Vt shifts using an optimization approach. Since the optimization uses the actual circuits, the resulting Vt shifts may be directly applied to post TID modeling of circuit behavior. The approach simplifies the effort for design and testing to determine TID degradation. The test chip fabricated and measured for this work is implemented on a 22 nm fully depleted silicon on insulator (FDSOI) with thin oxides. The approach is, however, applicable to any fabrication process. Finally, we show the extracted Vt changes due to TID vary with the transistor Vt (doping and well type).
- 16 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 69 (12) , 2305-2313
Total Ionizing Dose Impact on 22-nm FD-SOI Ring Oscillator Current and Frequency
Total ionizing dose (TID) has a significant effect on silicon on insulator (SOI) circuits, manifest primarily as a front gate threshold voltage (V t ) shift. This paper presents data on ring oscillator (RO) responses of 22 nm fully depleted (FD-SOI) thin oxide (core logic) devices to gamma-ray doses above 1 Mrad(Si). We show large current and frequency TID response differences between ROs comprised of different logic gates. Moreover, the extensive experimental results presented here show that these responses vary significantly with V t and well type. The measurements show that depending on the expected dose and transistor V t used, TID induced standby current (I SB ) increases may have substantial impact on overall power in space borne integrated circuits (ICs) using this fabrication process. The TID impact on digital circuit timing margins is also discussed.
- 16 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 69 (12) , 2305-2313
Total Ionizing Dose Impact on 22-nm FD-SOI Ring Oscillator Current and Frequency
Total ionizing dose (TID) has a significant effect on silicon on insulator (SOI) circuits, manifest primarily as a front gate threshold voltage (V t ) shift. This paper presents data on ring oscillator (RO) responses of 22 nm fully depleted (FD-SOI) thin oxide (core logic) devices to gamma-ray doses above 1 Mrad(Si). We show large current and frequency TID response differences between ROs comprised of different logic gates. Moreover, the extensive experimental results presented here show that these responses vary significantly with V t and well type. The measurements show that depending on the expected dose and transistor V t used, TID induced standby current (I SB ) increases may have substantial impact on overall power in space borne integrated circuits (ICs) using this fabrication process. The TID impact on digital circuit timing margins is also discussed.
- Open Access
- 7 June 2022
- Published by Elsevier in Microelectronics Journal
- Vol. 126
ASAP5: A predictive PDK for the 5 nm node
- 7 June 2022
- Published by Elsevier in Microelectronics Journal
- Vol. 126
Open AccessASAP5: A predictive PDK for the 5 nm node
- 25 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 69 (7) , 1602-1609
A Soft-Error Hardened by Design Microprocessor Implemented on Bulk 12-nm FinFET CMOS
We describe the porting of a soft-error (SE) hardened microprocessor to a modern 12-nm bulk CMOS finFET fabrication process and radiation testing results. The microprocessor includes latch-based cache and main register file (RF) arrays, with compact dual-patterned layouts. It is protected by dual modular redundancy (DMR) in the speculative pipeline, RF, and caches. Self-correcting triple modular redundant (TMR) flip-flops provide fine-grain protection in the TMR circuits that hold key architectural state. The DMR circuits are protected by checking circuits at the caches, RF, and crossovers to the TMR state. In the event of a DMR mismatch, an SE exception is taken, and the machine state is repaired via software. This approach also allows the detailed machine state reporting to elucidate the SE root cause circuits and cross sections. Broad beam radiation testing shows that it responds correctly to detected SEs. The by-circuit cross sections of the various circuits are reported for both heavy ions and protons.
- 25 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 69 (7) , 1602-1609
A Soft-Error Hardened by Design Microprocessor Implemented on Bulk 12-nm FinFET CMOS
We describe the porting of a soft-error (SE) hardened microprocessor to a modern 12-nm bulk CMOS finFET fabrication process and radiation testing results. The microprocessor includes latch-based cache and main register file (RF) arrays, with compact dual-patterned layouts. It is protected by dual modular redundancy (DMR) in the speculative pipeline, RF, and caches. Self-correcting triple modular redundant (TMR) flip-flops provide fine-grain protection in the TMR circuits that hold key architectural state. The DMR circuits are protected by checking circuits at the caches, RF, and crossovers to the TMR state. In the event of a DMR mismatch, an SE exception is taken, and the machine state is repaired via software. This approach also allows the detailed machine state reporting to elucidate the SE root cause circuits and cross sections. Broad beam radiation testing shows that it responds correctly to detected SEs. The by-circuit cross sections of the various circuits are reported for both heavy ions and protons.
- Open Access
- 28 January 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 69 (3) , 414-421
Measuring and Modeling Single Event Transients in 12-nm Inverters
In this article, we present a unique method of measuring single-event transient (SET) sensitivity in 12-nm FinFET technology. A test structure is presented that approximately measures the length of SETs using flip-flop shift registers with clock inputs driven by an inverter chain. The test structure was irradiated with ions at linear energy transfers (LETs) of 4.0, 5.6, 10.4, and 17.9 MeV-cm 2 /mg, and the cross sections of SET pulses measured down to 12.7 ps are presented. The experimental results are interpreted using a modeling methodology that combines TCAD and radiation effect simulations to capture the SET physics, and SPICE simulations to model the SETs in a circuit. The modeling shows that only ion strikes on the fin structure of the transistor would result in enough charge collected to produce SETs, while strikes in the subfin and substrate do not result in enough charge collected to produce measurable transients. Comparisons of the cumulative cross sections obtained from the experiment and from the simulations validate the modeling methodology presented.
- 28 January 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 69 (3) , 414-421
Open AccessMeasuring and Modeling Single Event Transients in 12-nm Inverters
In this article, we present a unique method of measuring single-event transient (SET) sensitivity in 12-nm FinFET technology. A test structure is presented that approximately measures the length of SETs using flip-flop shift registers with clock inputs driven by an inverter chain. The test structure was irradiated with ions at linear energy transfers (LETs) of 4.0, 5.6, 10.4, and 17.9 MeV-cm 2 /mg, and the cross sections of SET pulses measured down to 12.7 ps are presented. The experimental results are interpreted using a modeling methodology that combines TCAD and radiation effect simulations to capture the SET physics, and SPICE simulations to model the SETs in a circuit. The modeling shows that only ion strikes on the fin structure of the transistor would result in enough charge collected to produce SETs, while strikes in the subfin and substrate do not result in enough charge collected to produce measurable transients. Comparisons of the cumulative cross sections obtained from the experiment and from the simulations validate the modeling methodology presented.
- Open Access
- 1 November 2021
- Published by Office of Scientific and Technical Information (OSTI)
A Soft-Error Hardened by Design MicroprocessorImplemented in Bulk 12-nm FINFET CMOS.
This paper describes objective technical results and analysis. Any subjective views or opinions that might be expressed in the paper do not necessarily represent the views of the U.S. Department of Energy or the United States Government.
- 1 November 2021
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessA Soft-Error Hardened by Design MicroprocessorImplemented in Bulk 12-nm FINFET CMOS.
This paper describes objective technical results and analysis. Any subjective views or opinions that might be expressed in the paper do not necessarily represent the views of the U.S. Department of Energy or the United States Government.
- 5 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 68 (5) , 980-990
Multiscale System Modeling of Single-Event-Induced Faults in Advanced Node Processors
Integration-technology feature shrink increases computing-system susceptibility to single-event effects (SEE). While modeling SEE faults will be critical, an integrated processor's scope makes physically correct modeling computationally intractable. Without useful models, presilicon evaluation of fault-tolerance approaches becomes impossible. To incorporate accurate transistor-level effects at a system scope, we present a multiscale simulation framework. Charge collection at the 1) device level determines 2) circuit-level transient duration and state-upset likelihood. Circuit effects, in turn, impact 3) register-transfer-level architecture-state corruption visible at 4) the system level. Thus, the physically accurate effects of SEEs in large-scale systems, executed on a high-performance computing (HPC) simulator, could be used to drive cross-layer radiation hardening by design. We demonstrate the capabilities of this model with two case studies. First, we determine a D flip-flop's sensitivity at the transistor level on 14-nm FinFet technology, validating the model against published cross sections. Second, we track and estimate faults in a microprocessor without interlocked pipelined stages (MIPS) processor for Adams 90% worst case environment in an isotropic space environment.
- 5 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 68 (5) , 980-990
Multiscale System Modeling of Single-Event-Induced Faults in Advanced Node Processors
Integration-technology feature shrink increases computing-system susceptibility to single-event effects (SEE). While modeling SEE faults will be critical, an integrated processor's scope makes physically correct modeling computationally intractable. Without useful models, presilicon evaluation of fault-tolerance approaches becomes impossible. To incorporate accurate transistor-level effects at a system scope, we present a multiscale simulation framework. Charge collection at the 1) device level determines 2) circuit-level transient duration and state-upset likelihood. Circuit effects, in turn, impact 3) register-transfer-level architecture-state corruption visible at 4) the system level. Thus, the physically accurate effects of SEEs in large-scale systems, executed on a high-performance computing (HPC) simulator, could be used to drive cross-layer radiation hardening by design. We demonstrate the capabilities of this model with two case studies. First, we determine a D flip-flop's sensitivity at the transistor level on 14-nm FinFet technology, validating the model against published cross sections. Second, we track and estimate faults in a microprocessor without interlocked pipelined stages (MIPS) processor for Adams 90% worst case environment in an isotropic space environment.
- 10 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 68 (5) , 671-676
Evidence of Interface Trap Build-Up in Irradiated 14-nm Bulk FinFET Technologies
Total ionizing dose response of 14-nm bulk-Si FinFETs has been studied with a specially designed test chip. The radiation testing shows evidence of interface trap build-up on 14-nm Bulk FinFET technologies. These defects created in the isolation layer give rise to a new radiation-induced leakage path which might lead to a reliability issue in CMOS technologies at or below the 14-nm node. TCAD simulations are performed and an analytical model for TID-induced leakage current is presented to support analysis of the identified TID mechanism. TCAD simulation and analytical model results are consistent with the experimental data.
- 10 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 68 (5) , 671-676
Evidence of Interface Trap Build-Up in Irradiated 14-nm Bulk FinFET Technologies
Total ionizing dose response of 14-nm bulk-Si FinFETs has been studied with a specially designed test chip. The radiation testing shows evidence of interface trap build-up on 14-nm Bulk FinFET technologies. These defects created in the isolation layer give rise to a new radiation-induced leakage path which might lead to a reliability issue in CMOS technologies at or below the 14-nm node. TCAD simulations are performed and an analytical model for TID-induced leakage current is presented to support analysis of the identified TID mechanism. TCAD simulation and analytical model results are consistent with the experimental data.
- Top Cited Papers
- 1 January 2021
- Published by Elsevier in Microelectronics Journal
- Vol. 107
Comparing bulk-Si FinFET and gate-all-around FETs for the 5 nm technology node
- 1 January 2021
- Published by Elsevier in Microelectronics Journal
- Vol. 107
Top Cited PapersComparing bulk-Si FinFET and gate-all-around FETs for the 5 nm technology node