Jairo Arturo Escobar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jairo Arturo Escobar has a total of 44 co-authors. Here are the top co-authors by number of shared publications:
- Dachamir Hotza
Federal University of Santa Catarina
9 shared publications - Oscar Alvarez
Grupo de Diseño de Productos y Procesos (GDPP), Department of Chemical and Food Engineering, Universidad de los Andes, Bogotá 111711, Colombia
4 shared publications - Antonio Pedro Novaes de Oliveira
Programa de Pós‐graduação Em Ciência e Engenharia de Materiais – PGMAT Universidade Federal de Santa Catarina – UFSC Florianópolis Brazil
3 shared publications Laura Gómez
2 shared publications- Maria Teresa Colomer
Instituto de Cerámica y Vidrio (ICV), CSIC, c/Kelsen 5, E-28049 Madrid, Spain
2 shared publications - Rodrigo Moreno
Instituto de Cerámica y Vidrio (CSIC)
2 shared publications
Latest Publications
- 12 January 2017
- Published by Taylor & Francis in Materials and Manufacturing Processes
- Vol. 32 (7-8) , 749-755
Reconstruction of the lost Muisca Siecha raft pouring process by reverse engineering methodology
This work presents a study of a pre-Hispanic artifact based on a reverse engineering methodology, by which an object is reconstructed by computer-aided design to obtain information. The object of the study is the Siecha raft–a Muisca goldwork piece that disappeared in the nineteenth century and was reconstructed based on historical sources. The pouring process of the raft was studied by characterizing the metal flow within a mold, by using the analytical, experimental, and computational fluidity length parameter. After this, the flow was studied, by using estimated parameters from the previous three methods, in the reconstructed geometry of the raft. Pouring temperature, materials, and temperature of the mold, entrance velocity, and other parameters of the fabrication process were calculated. The results showed that the geometry of the raft could have been cast by gravity casting pouring process, with the calculated parameters.
- 12 January 2017
- Published by Taylor & Francis in Materials and Manufacturing Processes
- Vol. 32 (7-8) , 749-755
Reconstruction of the lost Muisca Siecha raft pouring process by reverse engineering methodology
This work presents a study of a pre-Hispanic artifact based on a reverse engineering methodology, by which an object is reconstructed by computer-aided design to obtain information. The object of the study is the Siecha raft–a Muisca goldwork piece that disappeared in the nineteenth century and was reconstructed based on historical sources. The pouring process of the raft was studied by characterizing the metal flow within a mold, by using the analytical, experimental, and computational fluidity length parameter. After this, the flow was studied, by using estimated parameters from the previous three methods, in the reconstructed geometry of the raft. Pouring temperature, materials, and temperature of the mold, entrance velocity, and other parameters of the fabrication process were calculated. The results showed that the geometry of the raft could have been cast by gravity casting pouring process, with the calculated parameters.
- 21 July 2016
- Published by SAGE Publications in Advances in Applied Ceramics: Structural, Functional and Bioceramics
- Vol. 116 (2) , 85-91
Alumina/copper foams produced by replica using a double impregnation process
Rheological behaviour of Al2O3 and CuO suspensions was characterised in order to fabricate Al2O3/Cu foams as an alternative way to produce foams with better mechanical properties than common Al2O3 foams. Different quantities of raw materials were combined to select the formulations for the ceramic-metal foams. Foams were produced by a double impregnation process, followed by a thermal cycle and a reduction cycle. In this work, materials were characterised trough zeta potential, SEM and optical dilatometry. Foams microstructure and compressive strength were evaluated. Final structures had a compressive resistance of 0.44 ± 0.14 MPa. GRAPHICAL ABSTRACT
- 21 July 2016
- Published by SAGE Publications in Advances in Applied Ceramics: Structural, Functional and Bioceramics
- Vol. 116 (2) , 85-91
Alumina/copper foams produced by replica using a double impregnation process
Rheological behaviour of Al2O3 and CuO suspensions was characterised in order to fabricate Al2O3/Cu foams as an alternative way to produce foams with better mechanical properties than common Al2O3 foams. Different quantities of raw materials were combined to select the formulations for the ceramic-metal foams. Foams were produced by a double impregnation process, followed by a thermal cycle and a reduction cycle. In this work, materials were characterised trough zeta potential, SEM and optical dilatometry. Foams microstructure and compressive strength were evaluated. Final structures had a compressive resistance of 0.44 ± 0.14 MPa. GRAPHICAL ABSTRACT
- 18 November 2015
- Published by Elsevier in Engineering Failure Analysis
- Vol. 60, 1-8
Failure analysis of submersible pump system collapse caused by assembly bolt crack propagation by stress corrosion cracking
- 18 November 2015
- Published by Elsevier in Engineering Failure Analysis
- Vol. 60, 1-8
Failure analysis of submersible pump system collapse caused by assembly bolt crack propagation by stress corrosion cracking
- 1 September 2013
- Published by Elsevier in Ceramics International
- Vol. 39 (7) , 8279-8285
Aqueous tape casting of micro and nano YSZ for SOFC electrolytes
- 1 September 2013
- Published by Elsevier in Ceramics International
- Vol. 39 (7) , 8279-8285
Aqueous tape casting of micro and nano YSZ for SOFC electrolytes
- 1 June 2013
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 33 (6) , 1137-1143
Manufacture of a non-stoichiometric LSM cathode SOFC material by aqueous tape casting
- 1 June 2013
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 33 (6) , 1137-1143
Manufacture of a non-stoichiometric LSM cathode SOFC material by aqueous tape casting
- 24 August 2012
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 727-728, 769-774
Characterization of SOFCS: A Crystallographic Analysis and First Steps towards an Impedance Spectroscopy Approach
Solid oxide fuel cells (SOFCs) have emerged as an efficient way to transform chemical energy into electrical energy. However, a major disadvantage of this technology is related to the high temperatures required for SOFC operation. In this way, new materials are necessary to maintain the electrical properties of the cell at intermediate temperatures. Based on these ideas, it is necessary to study both the structural variation of the cells components at different temperatures and their electrochemical behavior. In this work, a crystallographic characterization is presented, which was performed in a commercial SOFC cell using X-ray diffraction (XRD). An equivalent linear electrical model to predict SOFC losses is developed as well. Keywords: Solid oxide fuel cells (SOFCs); AC impedance; Electrochemical impedance spectroscopy (EIS); Equivalent circuit models.
- 24 August 2012
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 727-728, 769-774
Characterization of SOFCS: A Crystallographic Analysis and First Steps towards an Impedance Spectroscopy Approach
Solid oxide fuel cells (SOFCs) have emerged as an efficient way to transform chemical energy into electrical energy. However, a major disadvantage of this technology is related to the high temperatures required for SOFC operation. In this way, new materials are necessary to maintain the electrical properties of the cell at intermediate temperatures. Based on these ideas, it is necessary to study both the structural variation of the cells components at different temperatures and their electrochemical behavior. In this work, a crystallographic characterization is presented, which was performed in a commercial SOFC cell using X-ray diffraction (XRD). An equivalent linear electrical model to predict SOFC losses is developed as well. Keywords: Solid oxide fuel cells (SOFCs); AC impedance; Electrochemical impedance spectroscopy (EIS); Equivalent circuit models.
- 24 August 2012
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 727-728, 746-751
Manufacture of YSZ-LSM Semi-Cell by Colloidal Processing
Yttria stabilized zirconia (YSZ) is the most common electrolyte in solid oxide fuel cells (SOFC). The planar configuration is widely used for designing single cells, in which a thick cathode layer can be used as the supporting electrolyte film. The manufacture of the semi-cell formed by anode and electrolyte has been widely studied and there are many works dealing with its colloidal processing. However, the semi-cell formed by cathode and electrolyte has received much lower attention. This work deals with the manufacture of a semi-cell consisting of YSZ as electrolyte and strontium-doped lanthanum manganite (LSM) as a cathode through a colloidal processing route. The colloidal behavior of diluted suspensions of YSZ and the rheology of their concentrated suspensions were studied as a function of deflocculant content, mixing time by using ultrasounds probe and ageing time. The colloidal stability of aqueous suspensions of LSM was studied by measuring the zeta potential as a function of pH and deflocculant content. These concentrated suspensions were used to obtain thick self-sustained substrates by casting methods. The YSZ electrolyte and LSM cathode were prepared by tape casting in water medium.
- 24 August 2012
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 727-728, 746-751
Manufacture of YSZ-LSM Semi-Cell by Colloidal Processing
Yttria stabilized zirconia (YSZ) is the most common electrolyte in solid oxide fuel cells (SOFC). The planar configuration is widely used for designing single cells, in which a thick cathode layer can be used as the supporting electrolyte film. The manufacture of the semi-cell formed by anode and electrolyte has been widely studied and there are many works dealing with its colloidal processing. However, the semi-cell formed by cathode and electrolyte has received much lower attention. This work deals with the manufacture of a semi-cell consisting of YSZ as electrolyte and strontium-doped lanthanum manganite (LSM) as a cathode through a colloidal processing route. The colloidal behavior of diluted suspensions of YSZ and the rheology of their concentrated suspensions were studied as a function of deflocculant content, mixing time by using ultrasounds probe and ageing time. The colloidal stability of aqueous suspensions of LSM was studied by measuring the zeta potential as a function of pH and deflocculant content. These concentrated suspensions were used to obtain thick self-sustained substrates by casting methods. The YSZ electrolyte and LSM cathode were prepared by tape casting in water medium.
- 24 August 2012
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 727-728, 663-668
Manufacture and Characterization of Alumina Ceramic Foams for Porous Burners
Hazardous byproducts emissions such as nitrogen oxides (NOx) and carbon monoxide (CO) might be controlled by the use of radiant porous burners. Those heaters require a solid porous matrix where combustion reaction takes place, reason why the heat transfer is much more efficient. This project was based on a rheology study of an alumina slurry, where parameters like viscosity and tixotropy were the guide to select the appropriate formulation to be used in the fabrication of ceramic foams by the replica method. Low strength samples were produced after the first thermal treatment, explained by the absence of a plasticizer when using PVA as a binder. Incomplete sintered foams were obtained due to an insufficient soak time.
- 24 August 2012
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 727-728, 663-668
Manufacture and Characterization of Alumina Ceramic Foams for Porous Burners
Hazardous byproducts emissions such as nitrogen oxides (NOx) and carbon monoxide (CO) might be controlled by the use of radiant porous burners. Those heaters require a solid porous matrix where combustion reaction takes place, reason why the heat transfer is much more efficient. This project was based on a rheology study of an alumina slurry, where parameters like viscosity and tixotropy were the guide to select the appropriate formulation to be used in the fabrication of ceramic foams by the replica method. Low strength samples were produced after the first thermal treatment, explained by the absence of a plasticizer when using PVA as a binder. Incomplete sintered foams were obtained due to an insufficient soak time.
- 24 August 2012
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 727-728, 1069-1074
Continuum Isotropic Elastic Model for Sintering of Ceramic Materials
In this work a sintering model that assumes infinitesimal displacements rates has been structured using the continuum theory of sintering develop by Olevsky and Skorokhod [1, 2] and the sintering model develop by Sasan Kiani et al. [3, 4]. The model was used to estimate dimensional change and the density distribution using linear displacement rates (LRDs) as the only input. Furthermore, if the sintering potential and dense material shear viscosity are known, the stress distribution can be approximated. The magnitude of two stress norms (i.e. Von Misses stress and the stress tensor first invariant) determined using experimental and calculated LDRs are compared using three different geometries. From FEM simulation results it was inferred that densification can occur in presence of tension stresses if their magnitude is lower than the calculated sintering potential.
- 24 August 2012
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 727-728, 1069-1074
Continuum Isotropic Elastic Model for Sintering of Ceramic Materials
In this work a sintering model that assumes infinitesimal displacements rates has been structured using the continuum theory of sintering develop by Olevsky and Skorokhod [1, 2] and the sintering model develop by Sasan Kiani et al. [3, 4]. The model was used to estimate dimensional change and the density distribution using linear displacement rates (LRDs) as the only input. Furthermore, if the sintering potential and dense material shear viscosity are known, the stress distribution can be approximated. The magnitude of two stress norms (i.e. Von Misses stress and the stress tensor first invariant) determined using experimental and calculated LDRs are compared using three different geometries. From FEM simulation results it was inferred that densification can occur in presence of tension stresses if their magnitude is lower than the calculated sintering potential.
- Open Access
- 1 January 2012
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2012, 1-9
Relationship between Rheological Behaviour and Final Structure ofand YSZ Foams Produced by ReplicaUsing rheological parameters of ceramic suspensions, it is possible to taylor the structure of the ceramic foams produced by replica. This method consists in the impregnation of a polymeric flexible template (polyurethane foam) with a ceramic suspension (slurry) containing the appropriate additives, followed by burning out organic compounds and additives and sintering the ceramic structure. In this work, ceramic foams were produced by the replica method from Al2O3and 3% Y2O3-ZrO2. Rheological parameters of the ceramic suspensions were investigated to improve the mechanical performance of final structures. Different types and quantities of raw materials were combined in order to select the formulations for ceramic foams. The parameters that have a significant influence on the process are the binder type and the amount of solids. Significant changes on the hysteresis area of the suspensions resulted in a lower density of macrodefects in the material. Likewise, when the shear rate viscosity is enhanced, the thickness of the struts increased proportionally. Lastly, when the hysteresis area magnitude and the ceramic thickness increased, the material with higher uniformity was internally densified, and the stress concentration of the internal defects was smoothed
- 1 January 2012
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2012, 1-9
Open AccessRelationship between Rheological Behaviour and Final Structure ofand YSZ Foams Produced by ReplicaUsing rheological parameters of ceramic suspensions, it is possible to taylor the structure of the ceramic foams produced by replica. This method consists in the impregnation of a polymeric flexible template (polyurethane foam) with a ceramic suspension (slurry) containing the appropriate additives, followed by burning out organic compounds and additives and sintering the ceramic structure. In this work, ceramic foams were produced by the replica method from Al2O3and 3% Y2O3-ZrO2. Rheological parameters of the ceramic suspensions were investigated to improve the mechanical performance of final structures. Different types and quantities of raw materials were combined in order to select the formulations for ceramic foams. The parameters that have a significant influence on the process are the binder type and the amount of solids. Significant changes on the hysteresis area of the suspensions resulted in a lower density of macrodefects in the material. Likewise, when the shear rate viscosity is enhanced, the thickness of the struts increased proportionally. Lastly, when the hysteresis area magnitude and the ceramic thickness increased, the material with higher uniformity was internally densified, and the stress concentration of the internal defects was smoothed