Bing Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Bing Wang has a total of 95 co-authors. Here are the top co-authors by number of shared publications:
- Hongyan Yang
Guilin University of Electronic Technology
6 shared publications Siyuan Yu
Guangzhou Innovation Center of Optoelectronics and Microelectronics
6 shared publications- Gongli Xiao
Guangxi Key Laboratory of Precision Navigation Technology and Application, Guilin University of Electronic Technology, Guilin, China
4 shared publications Jurgen Michel
4 shared publicationsKenneth Eng Kian Lee
4 shared publicationsEugene A Fitzgerald
3 shared publications
Latest Publications
- 28 October 2026
- Published by Optica Publishing Group in Photonics Research
- Vol. 14 (11) , 4805
Distributed feedback lasers heterogeneously integrated on a standard 220 nm silicon photonics platform via direct bonding
Heterogeneous integration of III–V distributed feedback (DFB) lasers on silicon photonics platforms is the key technological step toward fully integrated on-chip photonic systems. However, its implementation on industry-standard 220 nm silicon photonics platforms is hindered by two major factors: weak optical interaction between the guided mode in the III–V gain region and the silicon-based DFB grating, and inefficient power transfer from the III–V active region to the silicon waveguide. Most prior demonstrations have been implemented on non-standard silicon-on-insulator (SOI) platforms featuring 400–500 nm thick silicon device layers, which enhances grating feedback and coupling efficiency. The use of a thick non-standard silicon layer compromises foundry compatibility, increases fabrication complexity, and complicates component design due to the emergence of higher-order vertical modes. Here we develop a heterogeneous integration technology that overcomes these obstacles, culminating in the integration of indium phosphide quantum well (InP QW) DFB lasers on a standard 220 nm silicon photonics platform. An ultrathin bonding interface is used to strengthen optical coupling between the III–V gain region and the silicon DFB grating so that a quarter-wave phase-shifted grating is fabricated with an optimized coupling coefficient that ensures stable single-mode operation. A multi-stage mode-size converter further enables efficient power transfer into the silicon waveguide within an ultra-compact footprint of ∼40 μm . The fabricated device exhibits a threshold current of 39 mA, a maximum on-chip output power of 8.3 mW per facet, a side-mode suppression ratio exceeding 49 dB, and a direct modulation bandwidth of ∼10 GHz at 20°C. Multi-wavelength operation from 1505 to 1575 nm is further achieved via grating engineering. This work demonstrates a scalable and foundry-compatible approach for high-density on-chip silicon photonic light sources supporting wavelength-division multiplexed optical interconnect applications.
- 28 October 2026
- Published by Optica Publishing Group in Photonics Research
- Vol. 14 (11) , 4805
Distributed feedback lasers heterogeneously integrated on a standard 220 nm silicon photonics platform via direct bonding
Heterogeneous integration of III–V distributed feedback (DFB) lasers on silicon photonics platforms is the key technological step toward fully integrated on-chip photonic systems. However, its implementation on industry-standard 220 nm silicon photonics platforms is hindered by two major factors: weak optical interaction between the guided mode in the III–V gain region and the silicon-based DFB grating, and inefficient power transfer from the III–V active region to the silicon waveguide. Most prior demonstrations have been implemented on non-standard silicon-on-insulator (SOI) platforms featuring 400–500 nm thick silicon device layers, which enhances grating feedback and coupling efficiency. The use of a thick non-standard silicon layer compromises foundry compatibility, increases fabrication complexity, and complicates component design due to the emergence of higher-order vertical modes. Here we develop a heterogeneous integration technology that overcomes these obstacles, culminating in the integration of indium phosphide quantum well (InP QW) DFB lasers on a standard 220 nm silicon photonics platform. An ultrathin bonding interface is used to strengthen optical coupling between the III–V gain region and the silicon DFB grating so that a quarter-wave phase-shifted grating is fabricated with an optimized coupling coefficient that ensures stable single-mode operation. A multi-stage mode-size converter further enables efficient power transfer into the silicon waveguide within an ultra-compact footprint of ∼40 μm . The fabricated device exhibits a threshold current of 39 mA, a maximum on-chip output power of 8.3 mW per facet, a side-mode suppression ratio exceeding 49 dB, and a direct modulation bandwidth of ∼10 GHz at 20°C. Multi-wavelength operation from 1505 to 1575 nm is further achieved via grating engineering. This work demonstrates a scalable and foundry-compatible approach for high-density on-chip silicon photonic light sources supporting wavelength-division multiplexed optical interconnect applications.
- 13 February 2026
- Published by Optica Publishing Group in Optics Express
- Vol. 34 (4) , 6650-6662
Structural color based on a TiO 2 semi-ellipsoidal nanostructures metasurface
Structural colors, an emerging pigment-free coloration technology, have attracted significant attention in recent years. TiO 2 -based all-dielectric metasurfaces exhibit outstanding performance in color saturation and loss control. However, in single-dielectric systems, multipolar modes, especially higher-order ones, are easily excited at nonresonant wavelengths, leading to undesired subsidiary peaks in the reflection spectrum and a reduction in color saturation. To address this problem, we propose and demonstrate a design with all-TiO 2 semi-ellipsoidal nanostructures as the unit cell. The continuously varying surface profile effectively suppresses higher-order modes. As a result, in contrast to nanostructures with abrupt geometric discontinuities, the metasurface can achieve high reflectance with narrow FWHM reflection peaks and cover a color range from blue-green to orange-red without relying on multilayer dielectric stacks. The fabricated semi-ellipsoidal TiO 2 nanostructures with specific periodicity achieved high saturation and pure color in structural coloration, when the reflectance spectrum exhibits a narrowband feature. This strategy not only affords additional degrees of freedom in geometric design but also reduces the complexity associated with material deposition and the fabrication of nanostructures featuring curved surfaces, thereby providing an avenue for the realization of structural color display devices with enhanced color purity.
- 13 February 2026
- Published by Optica Publishing Group in Optics Express
- Vol. 34 (4) , 6650-6662
Structural color based on a TiO 2 semi-ellipsoidal nanostructures metasurface
Structural colors, an emerging pigment-free coloration technology, have attracted significant attention in recent years. TiO 2 -based all-dielectric metasurfaces exhibit outstanding performance in color saturation and loss control. However, in single-dielectric systems, multipolar modes, especially higher-order ones, are easily excited at nonresonant wavelengths, leading to undesired subsidiary peaks in the reflection spectrum and a reduction in color saturation. To address this problem, we propose and demonstrate a design with all-TiO 2 semi-ellipsoidal nanostructures as the unit cell. The continuously varying surface profile effectively suppresses higher-order modes. As a result, in contrast to nanostructures with abrupt geometric discontinuities, the metasurface can achieve high reflectance with narrow FWHM reflection peaks and cover a color range from blue-green to orange-red without relying on multilayer dielectric stacks. The fabricated semi-ellipsoidal TiO 2 nanostructures with specific periodicity achieved high saturation and pure color in structural coloration, when the reflectance spectrum exhibits a narrowband feature. This strategy not only affords additional degrees of freedom in geometric design but also reduces the complexity associated with material deposition and the fabrication of nanostructures featuring curved surfaces, thereby providing an avenue for the realization of structural color display devices with enhanced color purity.
- 19 December 2025
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 40 (12) , 125012
Selective area growth of GaAs/AlGaAs-distributed Bragg reflectors on Ge substrates
We report the selective area epitaxial growth (SAG) of GaAs/AlGaAs-distributed Bragg reflectors on Ge substrates. Smooth surfaces with well-defined boundaries and up to 94% reflectivity were obtained. When using Ge as the buffer layer between III–V and Si substrates, the SAG method can mitigate the thermal mismatch between the vertical cavity surface–emitting lasers (VCSELs) thick epitaxial layers and the Si substrate. These findings indicate that direct epitaxial growth and integration of VCSELs on high-quality Ge buffer layers on large-diameter Si substrates can be realized.
- 19 December 2025
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 40 (12) , 125012
Selective area growth of GaAs/AlGaAs-distributed Bragg reflectors on Ge substrates
We report the selective area epitaxial growth (SAG) of GaAs/AlGaAs-distributed Bragg reflectors on Ge substrates. Smooth surfaces with well-defined boundaries and up to 94% reflectivity were obtained. When using Ge as the buffer layer between III–V and Si substrates, the SAG method can mitigate the thermal mismatch between the vertical cavity surface–emitting lasers (VCSELs) thick epitaxial layers and the Si substrate. These findings indicate that direct epitaxial growth and integration of VCSELs on high-quality Ge buffer layers on large-diameter Si substrates can be realized.
- 20 November 2025
- Published by Optica Publishing Group in Applied Optics
- Vol. 64 (34) , 10293-10301
Dynamically tunable terahertz ultra-wideband absorber based on a photosensitive silicon ring-coupled structure
Aiming to address the complexities of structural design and the limited dynamic tuning capabilities of traditional phase-change material absorbers, this study proposes a dynamically tunable terahertz ultra-wideband absorber based on a photosensitive silicon ring-coupled structure. The device features a periodic array design with a square-ring-circular coupling structure, forming a three-dimensional resonant system through a polycyclic olefin copolymer dielectric layer and a continuous gold film reflection layer at the bottom. The results indicate that when the photosensitive silicon conductivity ( σ Si ) is modulated to 1.5×10 5 S/m, the device achieves over 90% absorption in the spectral range of 1.83–4.07 THz. Conversely, when σ Si is reduced to 1.0×10 3 S/m, the device exhibits greater than 95% total reflection characteristics, resulting in a remarkable bistable response. The symmetry of the structure imparts polarization insensitivity, and the photosensitive silicon conductivity can be modulated by adjusting the power of the pump light source, allowing for flexible adjustment of the absorption bandwidth, with a maximum modulation depth reaching 94.61%. The principles underlying broadband high absorption are elucidated by integrating impedance matching theory, electric field current distribution, and electric dipole resonance. Additionally, an equivalent circuit model is introduced for quantitative analysis, while the Fresnel equation further elucidates the mechanism behind the blue-shift phenomenon of the absorption band under large-angle incidence. The designed absorber possesses a simple structure and dynamic tunability, indicating potential applications in stealth, high-resolution imaging, and 6G communication.
- 20 November 2025
- Published by Optica Publishing Group in Applied Optics
- Vol. 64 (34) , 10293-10301
Dynamically tunable terahertz ultra-wideband absorber based on a photosensitive silicon ring-coupled structure
Aiming to address the complexities of structural design and the limited dynamic tuning capabilities of traditional phase-change material absorbers, this study proposes a dynamically tunable terahertz ultra-wideband absorber based on a photosensitive silicon ring-coupled structure. The device features a periodic array design with a square-ring-circular coupling structure, forming a three-dimensional resonant system through a polycyclic olefin copolymer dielectric layer and a continuous gold film reflection layer at the bottom. The results indicate that when the photosensitive silicon conductivity ( σ Si ) is modulated to 1.5×10 5 S/m, the device achieves over 90% absorption in the spectral range of 1.83–4.07 THz. Conversely, when σ Si is reduced to 1.0×10 3 S/m, the device exhibits greater than 95% total reflection characteristics, resulting in a remarkable bistable response. The symmetry of the structure imparts polarization insensitivity, and the photosensitive silicon conductivity can be modulated by adjusting the power of the pump light source, allowing for flexible adjustment of the absorption bandwidth, with a maximum modulation depth reaching 94.61%. The principles underlying broadband high absorption are elucidated by integrating impedance matching theory, electric field current distribution, and electric dipole resonance. Additionally, an equivalent circuit model is introduced for quantitative analysis, while the Fresnel equation further elucidates the mechanism behind the blue-shift phenomenon of the absorption band under large-angle incidence. The designed absorber possesses a simple structure and dynamic tunability, indicating potential applications in stealth, high-resolution imaging, and 6G communication.
- 26 September 2025
- Published by Optica Publishing Group in Optics Express
- Vol. 33 (20) , 42489-42497
Design and fabrication of a dual-channel symmetric optical 90-degree hybrid based on an 8 × 8 multi-mode interferometer
We propose and demonstrate a dual-channel symmetric optical 90-degree hybrid on a 220 nm silicon-on-insulator (SOI) platform. The device integrates both coherent hybrid and signal splitting functions in a compact footprint based on an 8 × 8 multimode interference (MMI) structure, which helps reduce insertion loss and layout complexity. Simulations predict low phase error and high common-mode rejection ratio (CMRR). Experimental characterization confirms the functionality of the fabricated device. The hybrid formed by Output 1-4 exhibits CMRRs of over 10.6 dB in the 1520-1580 nm range, with a phase error of less than 9.5° in the 1520-1564 nm range. The Output 5-8 hybrid achieves CMRRs exceeding 15 dB in the 1520-1580 nm range, with a phase error remaining below 8.7° in the 1520-1564 nm range. These results validate the design and indicate the potential for further optimization in future fabrication iterations, highlighting the multifunctional integration advantage of the proposed device over conventional designs.
- 26 September 2025
- Published by Optica Publishing Group in Optics Express
- Vol. 33 (20) , 42489-42497
Design and fabrication of a dual-channel symmetric optical 90-degree hybrid based on an 8 × 8 multi-mode interferometer
We propose and demonstrate a dual-channel symmetric optical 90-degree hybrid on a 220 nm silicon-on-insulator (SOI) platform. The device integrates both coherent hybrid and signal splitting functions in a compact footprint based on an 8 × 8 multimode interference (MMI) structure, which helps reduce insertion loss and layout complexity. Simulations predict low phase error and high common-mode rejection ratio (CMRR). Experimental characterization confirms the functionality of the fabricated device. The hybrid formed by Output 1-4 exhibits CMRRs of over 10.6 dB in the 1520-1580 nm range, with a phase error of less than 9.5° in the 1520-1564 nm range. The Output 5-8 hybrid achieves CMRRs exceeding 15 dB in the 1520-1580 nm range, with a phase error remaining below 8.7° in the 1520-1564 nm range. These results validate the design and indicate the potential for further optimization in future fabrication iterations, highlighting the multifunctional integration advantage of the proposed device over conventional designs.
- 1 May 2025
- Published by Optica Publishing Group in Optics Letters
- Vol. 50 (9) , 3094-3097
Large free spectral range, high Q-factor microring resonator in thin-film lithium niobate photonics
A microring resonator (MRR) with a large free spectral range (FSR) and a high quality factor (Q-factor) is highly desirable in many fields, such as optical communication and sensing. However, realizing such an MRR in thin-film lithium niobate (TFLN) photonics is a significant challenge due to the low refractive index contrast between the shallow-etched core waveguide and the cladding. Here, we experimentally demonstrate that such an MRR can be successfully achieved in TFLN photonics by implementing wide MRR waveguides and weakly tapered gap waveguides, along with optimizing the coupling ratio between the bus waveguide and the MRR. The proposed all-pass MRR features an FSR of 6.5 nm and a Q-factor of 3.11 × 104. Moreover, using the same method, we also experimentally demonstrate an add-drop MRR with an FSR of 4.2 nm and a Q-factor of 6.69 × 105.
- 1 May 2025
- Published by Optica Publishing Group in Optics Letters
- Vol. 50 (9) , 3094-3097
Large free spectral range, high Q-factor microring resonator in thin-film lithium niobate photonics
A microring resonator (MRR) with a large free spectral range (FSR) and a high quality factor (Q-factor) is highly desirable in many fields, such as optical communication and sensing. However, realizing such an MRR in thin-film lithium niobate (TFLN) photonics is a significant challenge due to the low refractive index contrast between the shallow-etched core waveguide and the cladding. Here, we experimentally demonstrate that such an MRR can be successfully achieved in TFLN photonics by implementing wide MRR waveguides and weakly tapered gap waveguides, along with optimizing the coupling ratio between the bus waveguide and the MRR. The proposed all-pass MRR features an FSR of 6.5 nm and a Q-factor of 3.11 × 104. Moreover, using the same method, we also experimentally demonstrate an add-drop MRR with an FSR of 4.2 nm and a Q-factor of 6.69 × 105.
- 14 October 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 125 (16)
Facets evolution of selected area grown GaAs in circular windows on Ge-on-Si and Ge substrates
We report the epitaxial growth of GaAs on Ge buffers on Si (001) substrates covered by SiO2 masks patterned with 3 μm diameter circular windows by metalorganic chemical vapor deposition. The influence of As partial pressure on the crystal quality and facet evolution of GaAs was investigated. Scanning electron microscopy and atomic force microscopy revealed that the GaAs within the window region exhibited a relatively flat (001) crystal facet. Under high As partial pressures, the {111} facets of GaAs showed a pronounced orientation preference. At lower As partial pressures, the {111} and {110} facets of GaAs were roughly equally represented, aligning with the facet distribution structure predicted under As-rich conditions by the equilibrium crystal shape theory. The growth condition of high As partial pressure can effectively improve the growth quality of GaAs and obtain smooth GaAs film with a lower roughness. Due to the polarity mismatch between GaAs and Ge, antiphase domains persisted. We obtained GaAs samples free from antiphase domains and threading dislocations by utilizing a Ge 6° offcut toward (111) substrate. This work introduces a feasible approach for heteroepitaxial integration of III-V semiconductor lasers, in particular the vertical cavity surface emitting lasers (VCSELs) on silicon substrates via direct growth, and the modulation of sidewall crystal facets for VCSELs.
- 14 October 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 125 (16)
Facets evolution of selected area grown GaAs in circular windows on Ge-on-Si and Ge substrates
We report the epitaxial growth of GaAs on Ge buffers on Si (001) substrates covered by SiO2 masks patterned with 3 μm diameter circular windows by metalorganic chemical vapor deposition. The influence of As partial pressure on the crystal quality and facet evolution of GaAs was investigated. Scanning electron microscopy and atomic force microscopy revealed that the GaAs within the window region exhibited a relatively flat (001) crystal facet. Under high As partial pressures, the {111} facets of GaAs showed a pronounced orientation preference. At lower As partial pressures, the {111} and {110} facets of GaAs were roughly equally represented, aligning with the facet distribution structure predicted under As-rich conditions by the equilibrium crystal shape theory. The growth condition of high As partial pressure can effectively improve the growth quality of GaAs and obtain smooth GaAs film with a lower roughness. Due to the polarity mismatch between GaAs and Ge, antiphase domains persisted. We obtained GaAs samples free from antiphase domains and threading dislocations by utilizing a Ge 6° offcut toward (111) substrate. This work introduces a feasible approach for heteroepitaxial integration of III-V semiconductor lasers, in particular the vertical cavity surface emitting lasers (VCSELs) on silicon substrates via direct growth, and the modulation of sidewall crystal facets for VCSELs.
- 7 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 42 (24) , 8853-8858
Dual-Control Tunable Metalens With Large Zoom Range
Tunable metasurfaces present a novel approach to compact planar optics development. However, most tunable metasurfaces limit dynamic adjustability due to a single control method. In this study, we investigate the potential of integrating polarization with elastic materials and showcase a tunable metalens that leverages both polarization and stretching control. The tunable range through stretching is measured at 11.4 to 20.6 μm for x-polarization and 20.7 to 36.4 μm for y-polarization. The zoom range achieved is 213.8% of the minimum focal length. The metalens demonstrate a focusing efficiency of over 30% and almost diffraction-limited focusing. Additionally, we fabricate metalenses with polarization-only and stretch-only controls for comparison purposes. Our results indicate that the dual control approach effectively addresses the limitations of conventional polarization-multiplexed metalenses in achieving continuous zoom capability. Furthermore, compared to single-control tunable metalenses, the dual control metalens exhibits a significantly wider adjustable zoom range. We anticipate that this design holds promising application prospects in VR/AR display and holographic imaging.
- 7 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 42 (24) , 8853-8858
Dual-Control Tunable Metalens With Large Zoom Range
Tunable metasurfaces present a novel approach to compact planar optics development. However, most tunable metasurfaces limit dynamic adjustability due to a single control method. In this study, we investigate the potential of integrating polarization with elastic materials and showcase a tunable metalens that leverages both polarization and stretching control. The tunable range through stretching is measured at 11.4 to 20.6 μm for x-polarization and 20.7 to 36.4 μm for y-polarization. The zoom range achieved is 213.8% of the minimum focal length. The metalens demonstrate a focusing efficiency of over 30% and almost diffraction-limited focusing. Additionally, we fabricate metalenses with polarization-only and stretch-only controls for comparison purposes. Our results indicate that the dual control approach effectively addresses the limitations of conventional polarization-multiplexed metalenses in achieving continuous zoom capability. Furthermore, compared to single-control tunable metalenses, the dual control metalens exhibits a significantly wider adjustable zoom range. We anticipate that this design holds promising application prospects in VR/AR display and holographic imaging.
- 21 May 2024
- Published by Springer Nature in Science China Materials
- Vol. 67 (6) , 1926-1937
Stretchable, stable and high-performance optoelectronic sensors based on hydrogel for ultraviolet imaging and wireless alarm
- 21 May 2024
- Published by Springer Nature in Science China Materials
- Vol. 67 (6) , 1926-1937
Stretchable, stable and high-performance optoelectronic sensors based on hydrogel for ultraviolet imaging and wireless alarm
- 9 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 42 (6) , 2076-2082
Doublet Metalens for Polarization Conversion as Well as Focusing
The metalens created in accordance with the Pancharatnan-Berry (PB) phase principle are always addressed with circularly polarised (CP) incidence, resulting in a limitation in efficiency and optical path miniaturisation. This article proposes a cascaded two-layer structure for linear-to-circular polarization conversion and PB phase focusing. The structure consists of arrays on the upper and lower sides of the substrate, with periodic Au-elliptical-cylindrical (AEC) array arranged below the substrate to convert incident linearly polarised (LP) light into CP light, acting as a Quarter-wave plate (QWP); the TiO 2 array with different rotation angles are arranged on top of the substrate using the PB phase, so that the converted CP light will converge at one point. Comparing this design to a metalens with the same numerical aperture (NA) but without polarization conversion for CP light incidence effectively verifies the polarization conversion and focusing function of this integrated doublet metasurface. In addition to metalens focusing, this design concept is applicable to optical communication, sensing, storage, and other optically integrated devices.
- 9 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in Journal of Lightwave Technology
- Vol. 42 (6) , 2076-2082
Doublet Metalens for Polarization Conversion as Well as Focusing
The metalens created in accordance with the Pancharatnan-Berry (PB) phase principle are always addressed with circularly polarised (CP) incidence, resulting in a limitation in efficiency and optical path miniaturisation. This article proposes a cascaded two-layer structure for linear-to-circular polarization conversion and PB phase focusing. The structure consists of arrays on the upper and lower sides of the substrate, with periodic Au-elliptical-cylindrical (AEC) array arranged below the substrate to convert incident linearly polarised (LP) light into CP light, acting as a Quarter-wave plate (QWP); the TiO 2 array with different rotation angles are arranged on top of the substrate using the PB phase, so that the converted CP light will converge at one point. Comparing this design to a metalens with the same numerical aperture (NA) but without polarization conversion for CP light incidence effectively verifies the polarization conversion and focusing function of this integrated doublet metasurface. In addition to metalens focusing, this design concept is applicable to optical communication, sensing, storage, and other optically integrated devices.