Seho Kim
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Seho Kim has a total of 42 co-authors. Here are the top co-authors by number of shared publications:
- Grant Anthony Covic
Department of Electrical, Computer, and Software Engineering, The University of Auckland, Auckland, New Zealand
14 shared publications - Alexander K. Bailey
University of Auckland
4 shared publications - Duleepa J. Thrimawithana
The University of Auckland
4 shared publications - Fei Yang Lin
Department of Electrical, Computer and Software Engineering, The University of Auckland, Auckland, New Zealand
4 shared publications Grant A. Covic
Department of Electrical, Computer, and Software Engineering The University of Auckland Auckland New Zealand
4 shared publications- Brian S. Gu
Department of Electrical, Computer and Software Engineering, University of Auckland, Auckland, New Zealand
3 shared publications
Latest Publications
- 1 July 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (7) , 12314-12330
Anisotropic Loss Modeling of the Nanocrystalline Cores in IPT Pads for EV Charging Applications
ferrites in inductive power transfer (IPT) pads owing to their advantageous magnetic properties. Accurate loss modelling of the nanocrystalline core is therefore essential for reliable prediction of pad performance. However, due to the anisotropy of nanocrystalline ribbons with the flux angle, conventional modelling approaches result in considerable discrepancies in IPT applications. This paper proposes an anisotropic core loss modelling methodology based on full-range angular characterisation results of the nanocrystalline ribbon. An improved angle-dependent Steinmetz equation is derived to capture the loss behaviour at large flux angles and incorporated into the magnetic material model. The core loss simulation procedure is implemented by integrating Python into ANSYS Maxwell and applied to a lightweight nanocrystalline core specifically designed for an SAE-compliant WPT3 IPT pad at Z3 air gap. The modelling and experimental results demonstrate that the proposed method significantly improves the accuracy of core loss prediction compared with the conventional approach. Finally, a 10 kW IPT system is constructed to evaluate the pad performance using the designed nanocrystalline core. The measured results show that the nanocrystalline core achieves a 68.5% reduction in core weight with the cost of 2.72% decrease in dc-dc efficiency.
- 1 July 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (7) , 12314-12330
Anisotropic Loss Modeling of the Nanocrystalline Cores in IPT Pads for EV Charging Applications
ferrites in inductive power transfer (IPT) pads owing to their advantageous magnetic properties. Accurate loss modelling of the nanocrystalline core is therefore essential for reliable prediction of pad performance. However, due to the anisotropy of nanocrystalline ribbons with the flux angle, conventional modelling approaches result in considerable discrepancies in IPT applications. This paper proposes an anisotropic core loss modelling methodology based on full-range angular characterisation results of the nanocrystalline ribbon. An improved angle-dependent Steinmetz equation is derived to capture the loss behaviour at large flux angles and incorporated into the magnetic material model. The core loss simulation procedure is implemented by integrating Python into ANSYS Maxwell and applied to a lightweight nanocrystalline core specifically designed for an SAE-compliant WPT3 IPT pad at Z3 air gap. The modelling and experimental results demonstrate that the proposed method significantly improves the accuracy of core loss prediction compared with the conventional approach. Finally, a 10 kW IPT system is constructed to evaluate the pad performance using the designed nanocrystalline core. The measured results show that the nanocrystalline core achieves a 68.5% reduction in core weight with the cost of 2.72% decrease in dc-dc efficiency.
- Open Access
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal on Wireless Power Technologies
- Vol. 1, 1-11
Characterizations of Resistive Losses in Carbon Fiber Reinforced Polymer Protection Covers for Wireless EV Charging
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal on Wireless Power Technologies
- Vol. 1, 1-11
Open AccessCharacterizations of Resistive Losses in Carbon Fiber Reinforced Polymer Protection Covers for Wireless EV Charging
- Open Access
- 3 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 6, 2014-2026
Decoupled Three-Phase Winding for Wireless Power Transfer to Electric Vehicles
Heavy-duty dynamic wireless power transfer (DWPT) systems face implementation challenges such as component stress, magnetic interoperability and leakage. Multi-coil systems are a popular solution for stationary WPT, however their application to DWPT is complicated by the need for magnetic balancing. This paper proposes a novel three-phase (3φ) in-road primary that includes an integrated reflection winding. This not only provides a modular solution by magnetic decoupling, but it also contributes to leakage field reduction. The inter-phase coupling is shown to reduce to 1% in the presence of a secondary ferrite plane. Under 10kW operation, the 3φ primary is shown to be capable of reducing leakage magnetic fields by 26% over a conventional rectangular primary. Furthermore, a DC-DC efficiency of at least 94.4% is maintained under secondary misalignment.
- 3 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 6, 2014-2026
Open AccessDecoupled Three-Phase Winding for Wireless Power Transfer to Electric Vehicles
Heavy-duty dynamic wireless power transfer (DWPT) systems face implementation challenges such as component stress, magnetic interoperability and leakage. Multi-coil systems are a popular solution for stationary WPT, however their application to DWPT is complicated by the need for magnetic balancing. This paper proposes a novel three-phase (3φ) in-road primary that includes an integrated reflection winding. This not only provides a modular solution by magnetic decoupling, but it also contributes to leakage field reduction. The inter-phase coupling is shown to reduce to 1% in the presence of a secondary ferrite plane. Under 10kW operation, the 3φ primary is shown to be capable of reducing leakage magnetic fields by 26% over a conventional rectangular primary. Furthermore, a DC-DC efficiency of at least 94.4% is maintained under secondary misalignment.
- Open Access
- 30 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 6, 1215-1224
Impact of Encapsulation on the Core Loss of Ferrites in Inductive Power Transfer
Inductive power transfer (IPT) magnetics are often “potted” with an encapsulant material to improve thermal performance. Mismatched thermal expansion of the encapsulation and magnetic core materials creates a residual mechanical stress that permanently reduces the magnetic performance of the Mn-Zn ferrite core layer. An encapsulated small-scale Double-D IPT pad designed for 2.5kW is built and tested, and the core loss of the ferrite tiles increases by 121% after encapsulation with a polyurethane-based material. The change in the core loss of the potted IPT pad after encapsulation is predicted using finite element analysis, and the proposed method matches within 7.3%. Three methods are presented to mitigate this increase in losses and experimentally verified on ferrite toroids. These results show that the choice of encapsulation material significantly impacts the thermal, structural, and electromagnetic behavior of the IPT pad.
- 30 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 6, 1215-1224
Open AccessImpact of Encapsulation on the Core Loss of Ferrites in Inductive Power Transfer
Inductive power transfer (IPT) magnetics are often “potted” with an encapsulant material to improve thermal performance. Mismatched thermal expansion of the encapsulation and magnetic core materials creates a residual mechanical stress that permanently reduces the magnetic performance of the Mn-Zn ferrite core layer. An encapsulated small-scale Double-D IPT pad designed for 2.5kW is built and tested, and the core loss of the ferrite tiles increases by 121% after encapsulation with a polyurethane-based material. The change in the core loss of the potted IPT pad after encapsulation is predicted using finite element analysis, and the proposed method matches within 7.3%. Three methods are presented to mitigate this increase in losses and experimentally verified on ferrite toroids. These results show that the choice of encapsulation material significantly impacts the thermal, structural, and electromagnetic behavior of the IPT pad.
- Open Access
- 24 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 6, 537-550
Nanocrystalline Core Losses in High Power IPT Systems for EV Charging Applications
This article discusses the effectiveness of the nanocrystalline cores in high-power inductive power transfer (IPT) systems. The core losses and equivalent series resistances (ESRs) of the ferrite and nanocrystalline cores in IPT pads are simulated in ANSYS Maxwell based on measurements of their magnetic properties using the partial cancellation method. Simulated results are verified using experiments of core loss measurements in IPT pads. Both simulated and experimental findings show that the ESR of IPT pads using fractured nanocrystalline cores decreases with higher excitation current, contrary to the typical behaviour of an IPT pad built using ferrite. This behaviour is in accordance with characterisation results of ferrite and nanocrystalline toroids and is analysed using Steinmetz coefficients. A 10 kW IPT system is set up to validate the effectiveness of the fractured nanocrystalline cores. Compared to TDK N95 ferrite cores, an IPT system using non-fractured nanocrystalline cores has a 0.6% reduction in dc-dc efficiency, while that of fractured nanocrystalline cores improves by 0.1% and operates with a lower magnetic flux density within the magnetic core.
- 24 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 6, 537-550
Open AccessNanocrystalline Core Losses in High Power IPT Systems for EV Charging Applications
This article discusses the effectiveness of the nanocrystalline cores in high-power inductive power transfer (IPT) systems. The core losses and equivalent series resistances (ESRs) of the ferrite and nanocrystalline cores in IPT pads are simulated in ANSYS Maxwell based on measurements of their magnetic properties using the partial cancellation method. Simulated results are verified using experiments of core loss measurements in IPT pads. Both simulated and experimental findings show that the ESR of IPT pads using fractured nanocrystalline cores decreases with higher excitation current, contrary to the typical behaviour of an IPT pad built using ferrite. This behaviour is in accordance with characterisation results of ferrite and nanocrystalline toroids and is analysed using Steinmetz coefficients. A 10 kW IPT system is set up to validate the effectiveness of the fractured nanocrystalline cores. Compared to TDK N95 ferrite cores, an IPT system using non-fractured nanocrystalline cores has a 0.6% reduction in dc-dc efficiency, while that of fractured nanocrystalline cores improves by 0.1% and operates with a lower magnetic flux density within the magnetic core.
- Open Access
- 2 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 5, 1830-1841
Anisotropic Characterization of Nanocrystalline Alloys for Inductive Power Transfer
Nanocrystalline alloys are of interest in inductive power transfer (IPT) due to their higher saturation limits, permeability, and thermal conductivity compared to conventional Mn–Zn ferrites. However, due to the higher conductivity of nanocrystalline alloys, they have significant eddy current losses. This article demonstrates a core loss measurement method that considers the anisotropic behavior of fractured and laminated nanocrystalline ribbons. The proposed method uses a Maxwell coil to generate a uniform magnetic field, while samples of nanocrystalline ribbon are mechanically rotated within the magnetic field. Core loss is then measured using a hybrid calorimetric method that combines steady-state and transient measurements, enabling quick and accurate acquisition. The measured core loss of three different nanocrystalline ribbon samples is compared at 85 kHz for IPT applications. Finally, a modified Steinmetz equation dependent on the magnetic flux angle is proposed.
- 2 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 5, 1830-1841
Open AccessAnisotropic Characterization of Nanocrystalline Alloys for Inductive Power Transfer
Nanocrystalline alloys are of interest in inductive power transfer (IPT) due to their higher saturation limits, permeability, and thermal conductivity compared to conventional Mn–Zn ferrites. However, due to the higher conductivity of nanocrystalline alloys, they have significant eddy current losses. This article demonstrates a core loss measurement method that considers the anisotropic behavior of fractured and laminated nanocrystalline ribbons. The proposed method uses a Maxwell coil to generate a uniform magnetic field, while samples of nanocrystalline ribbon are mechanically rotated within the magnetic field. Core loss is then measured using a hybrid calorimetric method that combines steady-state and transient measurements, enabling quick and accurate acquisition. The measured core loss of three different nanocrystalline ribbon samples is compared at 85 kHz for IPT applications. Finally, a modified Steinmetz equation dependent on the magnetic flux angle is proposed.
- Open Access
- 10 August 2024
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 17 (14) , 2013-2025
Design and analysis of a decoupled three‐phase coil array for inductive power transfer systems
This article details the design process for a new three‐phase coil array. All of the coils are made to be mutually decoupled from one another which is achieved by introducing a high reluctance path in the ferrite structure for mutual flux using an airgap in addition to controlling the coil overlap. Simulation and experimental results of a matched three‐phase primary and secondary coupler, designed using the proposed novel decoupling mechanism, are presented to show that the high reluctance path introduced to decouple the coils still allows the main couplings to be maintained within an acceptable range. In contrast, negligible interphase couplings between coils in the primary or secondary were observed. Effective coupling, voltage and uncompensated power measurements are shown to verify the design is able to meet SAE J2954 WPT3 requirements. Finally, the leakage magnetic flux density, simulated under WPT3 conditions, shows that its RMS value remains significantly less than 27 µT at a 800 mm distance from the centre of the secondary coupler.
- 10 August 2024
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 17 (14) , 2013-2025
Open AccessDesign and analysis of a decoupled three‐phase coil array for inductive power transfer systems
This article details the design process for a new three‐phase coil array. All of the coils are made to be mutually decoupled from one another which is achieved by introducing a high reluctance path in the ferrite structure for mutual flux using an airgap in addition to controlling the coil overlap. Simulation and experimental results of a matched three‐phase primary and secondary coupler, designed using the proposed novel decoupling mechanism, are presented to show that the high reluctance path introduced to decouple the coils still allows the main couplings to be maintained within an acceptable range. In contrast, negligible interphase couplings between coils in the primary or secondary were observed. Effective coupling, voltage and uncompensated power measurements are shown to verify the design is able to meet SAE J2954 WPT3 requirements. Finally, the leakage magnetic flux density, simulated under WPT3 conditions, shows that its RMS value remains significantly less than 27 µT at a 800 mm distance from the centre of the secondary coupler.
- 31 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (10) , 11964-11973
Optimized Magnetic Core Layer in Inductive Power Transfer Pad for Electric Vehicle Charging
This paper proposes a reduced ferrite IPT system for EV charging using ferrite-based soft magnetic composites (SMCs). IPT pads typically consist of a significant amount of ferrite to improve field shaping for better magnetic coupling between the primary and the secondary pads. However, the costly and brittle nature of ferrite leaves the IPT pads vulnerable to harsh roadway conditions. The IPT pad design in this paper either replaces ferrite with SMCs or removes the ferrite to reduce system cost and improve mechanical robustness. The design methodology uses a genetic algorithm to optimise the geometry of the primary magnetic core layer with a combination of SMC and ferrite using ANSYS Maxwell based on the magnetic coupling, ferrite volume and magnetic leakage fields. The paper experimentally validates the optimised pad that reduces ferrite volume by 63% compared to a typical IPT pad that uses only ferrite. The optimised design has 11% coupling reduction, but also reduces magnetic field leakage by 8%. When considering end-to-end DC-DC efficiency, the reduction with the optimised system is no more than 0.65%. The minimal deterioration is due to the optimised placement of SMC in low B-field regions.
- 31 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (10) , 11964-11973
Optimized Magnetic Core Layer in Inductive Power Transfer Pad for Electric Vehicle Charging
This paper proposes a reduced ferrite IPT system for EV charging using ferrite-based soft magnetic composites (SMCs). IPT pads typically consist of a significant amount of ferrite to improve field shaping for better magnetic coupling between the primary and the secondary pads. However, the costly and brittle nature of ferrite leaves the IPT pads vulnerable to harsh roadway conditions. The IPT pad design in this paper either replaces ferrite with SMCs or removes the ferrite to reduce system cost and improve mechanical robustness. The design methodology uses a genetic algorithm to optimise the geometry of the primary magnetic core layer with a combination of SMC and ferrite using ANSYS Maxwell based on the magnetic coupling, ferrite volume and magnetic leakage fields. The paper experimentally validates the optimised pad that reduces ferrite volume by 63% compared to a typical IPT pad that uses only ferrite. The optimised design has 11% coupling reduction, but also reduces magnetic field leakage by 8%. When considering end-to-end DC-DC efficiency, the reduction with the optimised system is no more than 0.65%. The minimal deterioration is due to the optimised placement of SMC in low B-field regions.
- 4 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 7, 1-5
Effects of EV Steel Floor on Leakage Flux for High Power Wireless Charging Systems
This paper explores the accuracy of modelling electric vehicle (EV) steel flooring and assesses its interaction with leakage flux from an eddy current heating and emissions perspective in a high power inductive power transfer (IPT) wireless charging system (WCS). Existing literature presents aluminium (Al) shielding as a method of reducing leakage flux emissions adjacent to the EV body during charging. Findings in this work suggest Al shielding is effective at reducing eddy current heating, but ineffective at reducing leakage fields adjacent to the EV body in the presence of a steel EV floor. Experiments were performed to assess eddy current and leakage flux behavior and to verify finite element analysis (FEA) models. Recommendations are made regarding how steel can be modelled in FEA software in the absence of a detailed material model and methods are presented.
- 4 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 7, 1-5
Effects of EV Steel Floor on Leakage Flux for High Power Wireless Charging Systems
This paper explores the accuracy of modelling electric vehicle (EV) steel flooring and assesses its interaction with leakage flux from an eddy current heating and emissions perspective in a high power inductive power transfer (IPT) wireless charging system (WCS). Existing literature presents aluminium (Al) shielding as a method of reducing leakage flux emissions adjacent to the EV body during charging. Findings in this work suggest Al shielding is effective at reducing eddy current heating, but ineffective at reducing leakage fields adjacent to the EV body in the presence of a steel EV floor. Experiments were performed to assess eddy current and leakage flux behavior and to verify finite element analysis (FEA) models. Recommendations are made regarding how steel can be modelled in FEA software in the absence of a detailed material model and methods are presented.