Qi Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Qi Zhang has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
- Xingsong Wang
School of Mechanical Engineering, Southeast University, Nanjing, China
11 shared publications - Mengqian Tian
School of Mechanical Engineering, Southeast University, Nanjing 211189, China
4 shared publications Zikang Xiao
School of Automation, Nanjing University of Information Science and Technology, Nanjing, China
4 shared publications- Donghua Shen
School of Mechanical Engineering, Nanjing Institute of Technology, Nanjing, China
3 shared publications Yong Tao
School of Automation, Nanjing University of Information Science and Technology, Nanjing, China
3 shared publicationsMengqian Tian
School of Mechanical Engineering, Southeast University, Nanjing, China
2 shared publications
Latest Publications
- 8 June 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 11 (8) , 9271-9278
Design and Analysis of a Continuum Robot With Triple-Layer Intra-Segment Coupling and Inter-Segment Actuation Decoupling
Continuum robots show great potential in unstructured environments due to their superior safety and compliance compared to traditional articulated robots. However, their applications are limited by low load-bearing capacity and inter-segment actuation coupling. To address these issues, we propose a novel continuum robot featuring a triple-layer tendon system for intra-segment coupling and an inter-segment actuation decoupling structure. The coupling segment consists of serially connected spherical and socket joints with internal tendon channels. Triple-layer tendons pass through these channels, interconnecting the joints to enable synchronized motion from adjacent joints to the entire segment. For inter-segment decoupling, redirection pulleys are incorporated within the first two segments. Driving tendons for distal segments are routed through these pulleys and exit from the base segment to external actuators, ensuring independent motion of each segment. Experimental results demonstrate that the intra-segment coupling significantly enhances stiffness and load capacity. Motion experiments confirm effective spherical joint coupling and accurate bending angle tracking of sinusoidal references. The comprehensive experimental results of the three-segment continuum robot show that the segments have good decoupling performance and the robot possesses high repeatability positioning accuracy.
- 8 June 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 11 (8) , 9271-9278
Design and Analysis of a Continuum Robot With Triple-Layer Intra-Segment Coupling and Inter-Segment Actuation Decoupling
Continuum robots show great potential in unstructured environments due to their superior safety and compliance compared to traditional articulated robots. However, their applications are limited by low load-bearing capacity and inter-segment actuation coupling. To address these issues, we propose a novel continuum robot featuring a triple-layer tendon system for intra-segment coupling and an inter-segment actuation decoupling structure. The coupling segment consists of serially connected spherical and socket joints with internal tendon channels. Triple-layer tendons pass through these channels, interconnecting the joints to enable synchronized motion from adjacent joints to the entire segment. For inter-segment decoupling, redirection pulleys are incorporated within the first two segments. Driving tendons for distal segments are routed through these pulleys and exit from the base segment to external actuators, ensuring independent motion of each segment. Experimental results demonstrate that the intra-segment coupling significantly enhances stiffness and load capacity. Motion experiments confirm effective spherical joint coupling and accurate bending angle tracking of sinusoidal references. The comprehensive experimental results of the three-segment continuum robot show that the segments have good decoupling performance and the robot possesses high repeatability positioning accuracy.
- 11 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (12) , 18799-18810
Joint-Level Intent Recognition of Upper Limb Based on XGBoost and Viterbi Decoding
sEMG-based upper-limb motion intent recognition is challenging due to the high flexibility of upper-limb joints. Existing methods that classify overall actions often struggle to generalize to unseen movements, lack joint-level interpretability, and suffer from prediction jitter in real-time frame-level outputs.To address these issues, this study proposes an upper-limb intent recognition framework based on XGBoost and Viterbi decoding. Complex movements are decomposed into two functional sub-models for the shoulder and elbow joints. An automatic activation detection method based on time–frequency energy changes is introduced, and Viterbi decoding is applied to improve temporal continuity.Experimental results show that the proposed framework can effectively recognize unseen complex movements, achieving an average accuracy of 94% in typical daily activities. Compared with raw frame-level predictions, Viterbi-based temporal optimization significantly reduces label switching frequency and improves prediction stability.
- 11 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (12) , 18799-18810
Joint-Level Intent Recognition of Upper Limb Based on XGBoost and Viterbi Decoding
sEMG-based upper-limb motion intent recognition is challenging due to the high flexibility of upper-limb joints. Existing methods that classify overall actions often struggle to generalize to unseen movements, lack joint-level interpretability, and suffer from prediction jitter in real-time frame-level outputs.To address these issues, this study proposes an upper-limb intent recognition framework based on XGBoost and Viterbi decoding. Complex movements are decomposed into two functional sub-models for the shoulder and elbow joints. An automatic activation detection method based on time–frequency energy changes is introduced, and Viterbi decoding is applied to improve temporal continuity.Experimental results show that the proposed framework can effectively recognize unseen complex movements, achieving an average accuracy of 94% in typical daily activities. Compared with raw frame-level predictions, Viterbi-based temporal optimization significantly reduces label switching frequency and improves prediction stability.
- 20 November 2025
- Published by Elsevier in Sensors and Actuators A: Physical
- Vol. 398
A modular 3D-printed bone-muscle integrated actuator for wearable exoskeletons
- 20 November 2025
- Published by Elsevier in Sensors and Actuators A: Physical
- Vol. 398
A modular 3D-printed bone-muscle integrated actuator for wearable exoskeletons
- 1 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 10 (9) , 9534-9541
Multi-Joint Actuation of Robotic Arm Using a Switchable Tendon-Sheath Drive System
Wearable upper limb exoskeletons and robot arms have shown great application prospects in both daily life and industrial applications. However, since human arms have many degrees of freedom, these robotic devices usually require a large number of actuators to provide sufficient driving force and flexibility. For most motor-driven robotic arms, this drive requirement typically results in a large, heavy, and costly system. Furthermore, the increase in the number of motors also brings additional energy consumption. To address this, we proposed a switchable tendon-sheath drive system that can achieve multi-joint actuation with only one main drive motor. It uses a tristable clutch to switch the end anchor at the output end of the tendon-sheath mechanism. Based on this actuation system, we developed a two-degree-of-freedom robotic arm platform and a voice control method, and conducted experimental studies to evaluate the multi-joint actuation performance. The experimental results demonstrated that the switchable tendon-sheath system successfully realizes the motion control of the shoulder and elbow joints using a main drive motor, and the self-locking ability of the clutch can effectively maintains the joint posture under variable load conditions.
- 1 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 10 (9) , 9534-9541
Multi-Joint Actuation of Robotic Arm Using a Switchable Tendon-Sheath Drive System
Wearable upper limb exoskeletons and robot arms have shown great application prospects in both daily life and industrial applications. However, since human arms have many degrees of freedom, these robotic devices usually require a large number of actuators to provide sufficient driving force and flexibility. For most motor-driven robotic arms, this drive requirement typically results in a large, heavy, and costly system. Furthermore, the increase in the number of motors also brings additional energy consumption. To address this, we proposed a switchable tendon-sheath drive system that can achieve multi-joint actuation with only one main drive motor. It uses a tristable clutch to switch the end anchor at the output end of the tendon-sheath mechanism. Based on this actuation system, we developed a two-degree-of-freedom robotic arm platform and a voice control method, and conducted experimental studies to evaluate the multi-joint actuation performance. The experimental results demonstrated that the switchable tendon-sheath system successfully realizes the motion control of the shoulder and elbow joints using a main drive motor, and the self-locking ability of the clutch can effectively maintains the joint posture under variable load conditions.
- 14 June 2025
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 239 (16) , 6493-6501
Elongation modeling and compensation control of compound tendon-sheath artificial muscle
Muscle-like actuators have recently emerged to serve bionic robots and human-robot interaction systems. In order to enhance the performance of exoskeletons, we have introduced an artificial muscle based on the Hill muscle model, which incorporates a compliant structure and muscle-like elastic properties. By drawing inspiration from antagonistic muscle pairs, we develop a compound tendon-sheath artificial muscle (CTSAM) capable of bidirectional movement. To address control challenges arising from the nonlinear transmission characteristics of the CTSAM, this paper establishes an elongation model and proposes a control method that combines elongation model compensation with sliding mode control. This control method is subsequently validated through experiments involving various motion trajectories. The experimental results demonstrate that control errors are effectively reduced, and error fluctuations with changes in movement frequency are significantly mitigated.
- 14 June 2025
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 239 (16) , 6493-6501
Elongation modeling and compensation control of compound tendon-sheath artificial muscle
Muscle-like actuators have recently emerged to serve bionic robots and human-robot interaction systems. In order to enhance the performance of exoskeletons, we have introduced an artificial muscle based on the Hill muscle model, which incorporates a compliant structure and muscle-like elastic properties. By drawing inspiration from antagonistic muscle pairs, we develop a compound tendon-sheath artificial muscle (CTSAM) capable of bidirectional movement. To address control challenges arising from the nonlinear transmission characteristics of the CTSAM, this paper establishes an elongation model and proposes a control method that combines elongation model compensation with sliding mode control. This control method is subsequently validated through experiments involving various motion trajectories. The experimental results demonstrate that control errors are effectively reduced, and error fluctuations with changes in movement frequency are significantly mitigated.
- Open Access
- 27 May 2025
- Published by MDPI AG in Biomimetics
- Vol. 10 (6) , 349
Development of a Passive Back-Support Exoskeleton Mimicking Human Spine Motion for Multi-Posture Assistance in Occupational Tasks
Passive back-support exoskeletons commonly employ elastic components to assist users during dynamic tasks. However, these designs are ineffective in providing sustained assistance for prolonged static bending postures, such as those required in surgery, assembly, and farming, where users experience continuous lumbar flexion. To address this limitation, a novel passive back-support exoskeleton inspired by the human spine is proposed in this work. The exoskeleton integrates a five-bar linkage mechanism with vertebrae-mimicking units, allowing for both dynamic flexion–extension movements and rigid support at various flexion angles. During the experiments, subjects are instructed to perform a 30-min forward-bending assembly task under two conditions: with and without wearing the exoskeleton. Compared to the free condition, the electromyography results indicate a 10.1% reduction in integrated EMG (IEMG) and a 9.78% decrease in root mean square (RMS) values of the erector spinae with the exoskeleton. Meanwhile, the metabolic rate is decreased by 11.1%, highlighting the effectiveness of the exoskeleton in mitigating muscle fatigue during prolonged static work. This work provides a promising solution for reducing musculoskeletal strain in occupations requiring sustained forward bending, making it a valuable advancement in passive exoskeleton technology.
- 27 May 2025
- Published by MDPI AG in Biomimetics
- Vol. 10 (6) , 349
Open AccessDevelopment of a Passive Back-Support Exoskeleton Mimicking Human Spine Motion for Multi-Posture Assistance in Occupational Tasks
Passive back-support exoskeletons commonly employ elastic components to assist users during dynamic tasks. However, these designs are ineffective in providing sustained assistance for prolonged static bending postures, such as those required in surgery, assembly, and farming, where users experience continuous lumbar flexion. To address this limitation, a novel passive back-support exoskeleton inspired by the human spine is proposed in this work. The exoskeleton integrates a five-bar linkage mechanism with vertebrae-mimicking units, allowing for both dynamic flexion–extension movements and rigid support at various flexion angles. During the experiments, subjects are instructed to perform a 30-min forward-bending assembly task under two conditions: with and without wearing the exoskeleton. Compared to the free condition, the electromyography results indicate a 10.1% reduction in integrated EMG (IEMG) and a 9.78% decrease in root mean square (RMS) values of the erector spinae with the exoskeleton. Meanwhile, the metabolic rate is decreased by 11.1%, highlighting the effectiveness of the exoskeleton in mitigating muscle fatigue during prolonged static work. This work provides a promising solution for reducing musculoskeletal strain in occupations requiring sustained forward bending, making it a valuable advancement in passive exoskeleton technology.
- Open Access
- 28 April 2025
- Published by MDPI AG in Biomimetics
- Vol. 10 (5) , 271
Biomimetic Design and Validation of an Adaptive Cable-Driven Elbow Exoskeleton Inspired by the Shrimp Shell
The application of exoskeleton robots has demonstrated promising effectiveness in promoting the recovery of motor skills in patients with upper limb dysfunction. However, the joint misalignment caused by rigid exoskeletons usually leads to an uncomfortable experience for users. In this work, an adaptive cable-driven elbow exoskeleton inspired by the structural characteristics of the shrimp shell was developed to facilitate the rehabilitation of the elbow joint and to provide more compliant human-exoskeleton interactions. The exoskeleton was specifically designed for elbow flexion and extension, with a total weight of approximately 0.6 kg. Based on the mechanical design and cable configuration of the exoskeleton, the kinematics and dynamics of driving cables were analyzed. Subsequently, a PID-based control strategy was designed with cable kinematics. To evaluate the practical performance of the proposed exoskeleton in elbow assistance, a prototype was established and experimented with six subjects. According to the experimental results, the measured elbow joint angle trajectory is generally consistent with the desired trajectory, with a mean position tracking accuracy of approximately 0.997, which supports motion stability in rehabilitation scenarios. Meanwhile, the collected sEMG values from biceps brachii and brachioradialis under the exoskeleton condition show a significant reduction in average muscle activation by 37.7% and 28.8%, respectively, compared to the condition without exoskeleton.
- 28 April 2025
- Published by MDPI AG in Biomimetics
- Vol. 10 (5) , 271
Open AccessBiomimetic Design and Validation of an Adaptive Cable-Driven Elbow Exoskeleton Inspired by the Shrimp Shell
The application of exoskeleton robots has demonstrated promising effectiveness in promoting the recovery of motor skills in patients with upper limb dysfunction. However, the joint misalignment caused by rigid exoskeletons usually leads to an uncomfortable experience for users. In this work, an adaptive cable-driven elbow exoskeleton inspired by the structural characteristics of the shrimp shell was developed to facilitate the rehabilitation of the elbow joint and to provide more compliant human-exoskeleton interactions. The exoskeleton was specifically designed for elbow flexion and extension, with a total weight of approximately 0.6 kg. Based on the mechanical design and cable configuration of the exoskeleton, the kinematics and dynamics of driving cables were analyzed. Subsequently, a PID-based control strategy was designed with cable kinematics. To evaluate the practical performance of the proposed exoskeleton in elbow assistance, a prototype was established and experimented with six subjects. According to the experimental results, the measured elbow joint angle trajectory is generally consistent with the desired trajectory, with a mean position tracking accuracy of approximately 0.997, which supports motion stability in rehabilitation scenarios. Meanwhile, the collected sEMG values from biceps brachii and brachioradialis under the exoskeleton condition show a significant reduction in average muscle activation by 37.7% and 28.8%, respectively, compared to the condition without exoskeleton.
- 19 December 2022
- Published by Springer Nature in Journal of Intelligent & Robotic Systems
- Vol. 106 (4) , 1-10
Model-based Force Control of a Tendon-Sheath Actuated Slender Gripper Without Output Feedback
- 19 December 2022
- Published by Springer Nature in Journal of Intelligent & Robotic Systems
- Vol. 106 (4) , 1-10
Model-based Force Control of a Tendon-Sheath Actuated Slender Gripper Without Output Feedback
- 16 May 2022
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 236 (17) , 9743-9752
Single-motor driven multi-joints lower limb exoskeleton system based on controllable clamper
In this paper, a scheme of single-motor driven multi-joints lower limb exoskeleton based on controllable clamper is proposed in order to reduce the number of driving motors, overall weight and structural complexity of the lower limb exoskeleton. We propose a new type of tendon-sheath artificial muscle as the transmission method for exoskeleton according to the Hill muscle model. A controllable clamper is used to control the contraction and relaxation of the artificial muscle, and a pair of series and parallel springs is used to imitate the characteristics of the muscle. On this basis, we designed the mechanical structure of the system, and figure out the relationship between assistant force and driving motor’s angle, then planned the control timing sequence of the clampers. The driving motor’s angle curve is determined by theoretical calculation. A platform is built, and the experimental results verify that the scheme of single motor to drive multi-joints is feasible and effective.
- 16 May 2022
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 236 (17) , 9743-9752
Single-motor driven multi-joints lower limb exoskeleton system based on controllable clamper
In this paper, a scheme of single-motor driven multi-joints lower limb exoskeleton based on controllable clamper is proposed in order to reduce the number of driving motors, overall weight and structural complexity of the lower limb exoskeleton. We propose a new type of tendon-sheath artificial muscle as the transmission method for exoskeleton according to the Hill muscle model. A controllable clamper is used to control the contraction and relaxation of the artificial muscle, and a pair of series and parallel springs is used to imitate the characteristics of the muscle. On this basis, we designed the mechanical structure of the system, and figure out the relationship between assistant force and driving motor’s angle, then planned the control timing sequence of the clampers. The driving motor’s angle curve is determined by theoretical calculation. A platform is built, and the experimental results verify that the scheme of single motor to drive multi-joints is feasible and effective.
- 23 February 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 6 (2) , 3744-3751
Design and Analysis of a Snake-Inspired Crawling Robot Driven by Alterable Angle Scales
Inspired by the anisotropic friction of snakes' scales, many snake-like robots actuated by scales have been developed. However, these robots' scales' angle is unalterable, causing them to crawl in only one direction. Moreover, these robots typically require complex controllers to control their locomotion. To address these limitations, the letter proposes a crawling robot with alterable angle scales, a soft actuator, and an autonomous vibrating valve. All scales are strung on a spring wire and can rotate freely, and an airbag can easily control the rotation. The robot can crawl backward after flipping the scales' orientation. A piston located inside the vibrating valve can be periodically pushed by a reset spring and air pressure to achieve reciprocating motion, which results in periodic inflating and deflating of the soft actuator. Such that the crawling robot can move automatically. The locomotion mechanism was analyzed, and a dynamic model was built. The locomotion performance was tested by experiments. The experimental results show that both the forward and backward locomotion speed can be improved by increasing the driving pressure. When the driving pressure is 195 kPa, the robot can crawl forward and backward at the speed of 49.0 mm/s and 38.2 mm/s, respectively.
- 23 February 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 6 (2) , 3744-3751
Design and Analysis of a Snake-Inspired Crawling Robot Driven by Alterable Angle Scales
Inspired by the anisotropic friction of snakes' scales, many snake-like robots actuated by scales have been developed. However, these robots' scales' angle is unalterable, causing them to crawl in only one direction. Moreover, these robots typically require complex controllers to control their locomotion. To address these limitations, the letter proposes a crawling robot with alterable angle scales, a soft actuator, and an autonomous vibrating valve. All scales are strung on a spring wire and can rotate freely, and an airbag can easily control the rotation. The robot can crawl backward after flipping the scales' orientation. A piston located inside the vibrating valve can be periodically pushed by a reset spring and air pressure to achieve reciprocating motion, which results in periodic inflating and deflating of the soft actuator. Such that the crawling robot can move automatically. The locomotion mechanism was analyzed, and a dynamic model was built. The locomotion performance was tested by experiments. The experimental results show that both the forward and backward locomotion speed can be improved by increasing the driving pressure. When the driving pressure is 195 kPa, the robot can crawl forward and backward at the speed of 49.0 mm/s and 38.2 mm/s, respectively.