Saba Y. Ahmed
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Saba Y. Ahmed has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
Basim A. Abass
3 shared publications- Farooq Hassan Ali
Mechanical Engineering Department, College of Engineering, University of Babylon
3 shared publications Hameed K. Hamzah
College of Engineering-Mechanical Engineering Department, University of Babylon, Babylon City, Hilla, Iraq
2 shared publications- Hameed Kadhem Hamzah
Mechanical Engineering Department, College of Engineering, University of Babylon
2 shared publications Mohammed Y. Jabbar
Mechanical Engineering Department College of Engineering, University of Babylon Babylon Iraq
2 shared publications- Mohammed Y. Jabbar
Department of Mechanical Engineering, University of Babylon, Babylon, Iraq
2 shared publications
Latest Publications
- Open Access
- 25 April 2024
- Published by Elsevier in Applications in Energy and Combustion Science
- Vol. 18
Flame morphology and laminar flame assessments affected by flames interaction using multi-ignition sources of NH3/H2-air flames
- 25 April 2024
- Published by Elsevier in Applications in Energy and Combustion Science
- Vol. 18
Open AccessFlame morphology and laminar flame assessments affected by flames interaction using multi-ignition sources of NH3/H2-air flames
- 9 April 2024
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 149 (10) , 4873-4891
Enhancement of system conversion energy from I.C. engine exhaust using heat exchanger and thermoelectric generators
- 9 April 2024
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 149 (10) , 4873-4891
Enhancement of system conversion energy from I.C. engine exhaust using heat exchanger and thermoelectric generators
- 9 June 2023
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 148 (14) , 6607-6644
Exploratory review of the heat exchanger and cooler geometrical effect on energy harvesting from automobile exhaust using thermoelectric generators
- 9 June 2023
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 148 (14) , 6607-6644
Exploratory review of the heat exchanger and cooler geometrical effect on energy harvesting from automobile exhaust using thermoelectric generators
- Open Access
- 1 January 2023
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in FME Transactions
- Vol. 51 (4) , 550-563
Performance analysis of elliptical journal bearing lubricated with experimentally characterized nanolubricant considering thermal effect using CFD technique
This study uses computational fluid dynamics (CFD) to quantitatively examine the performance of an elliptical journal bearing (EJB) lubricated with TiO2 and ZnO nano-lubricant considering thermal effect. In an experiment, nanoparticles with particle concentrations varying from 0 to 2 weight percent are mixed with SAE15W40 engine oil to create these lubricants. The impact of weight fractions, rotational speed, eccentricity, and ellipticity ratios on the thermal performance of the EJB has been examined. The Kreger-Dougherty model is employed to understand the effects of oil film temperature as well as nanoparticle concentration on lubricant viscosity. The pressure and temperature determined by (Dang 2020) and (Wang 2021were evaluated against the CFD model with good agreement. The findings show that for 2 wt% nanoparticles, e of 0.6 and N of 5000 rpm, the load-carrying capacity increased by 5.5% and 4% and the side leakage flow decreased by 24.4% and 18%.
- 1 January 2023
- Published by Centre for Evaluation in Education and Science (CEON/CEES) in FME Transactions
- Vol. 51 (4) , 550-563
Open AccessPerformance analysis of elliptical journal bearing lubricated with experimentally characterized nanolubricant considering thermal effect using CFD technique
This study uses computational fluid dynamics (CFD) to quantitatively examine the performance of an elliptical journal bearing (EJB) lubricated with TiO2 and ZnO nano-lubricant considering thermal effect. In an experiment, nanoparticles with particle concentrations varying from 0 to 2 weight percent are mixed with SAE15W40 engine oil to create these lubricants. The impact of weight fractions, rotational speed, eccentricity, and ellipticity ratios on the thermal performance of the EJB has been examined. The Kreger-Dougherty model is employed to understand the effects of oil film temperature as well as nanoparticle concentration on lubricant viscosity. The pressure and temperature determined by (Dang 2020) and (Wang 2021were evaluated against the CFD model with good agreement. The findings show that for 2 wt% nanoparticles, e of 0.6 and N of 5000 rpm, the load-carrying capacity increased by 5.5% and 4% and the side leakage flow decreased by 24.4% and 18%.
- 12 September 2022
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 48 (3) , 3599-3614
Performance Analysis of Experimentally Characterized Titanium Dioxide and Zinc Oxide Nano-Lubricated Journal Bearing Considering Thermal and Cavitation Effects
- 12 September 2022
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 48 (3) , 3599-3614
Performance Analysis of Experimentally Characterized Titanium Dioxide and Zinc Oxide Nano-Lubricated Journal Bearing Considering Thermal and Cavitation Effects
- 7 March 2022
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 47 (12) , 15489-15504
In a Vented Square Enclosure, the Effect of a Flexible Baffle Attached to a Solid Cylinder on Mixed Convection
- 7 March 2022
- Published by Springer Nature in Arabian Journal for Science and Engineering
- Vol. 47 (12) , 15489-15504
In a Vented Square Enclosure, the Effect of a Flexible Baffle Attached to a Solid Cylinder on Mixed Convection
- 31 July 2020
- Published by Wiley in Heat Transfer
- Vol. 50 (1) , 466-486
Experimental study of closed‐loop thermosyphon with a different evaporator geometry
In this study, the effect of evaporator geometry on the loop thermosyphon's heat transfer coefficient is experimentally verified by using water as a working fluid with three filling ratios (50%, 70%, 90%), constant heat input (185 W), and condenser cooling water flow rate remaining constant at 2 Lpm. Three evaporator pipes are used (I: straight; II: helical coil evaporator with a diameter of 100‐mm coil and two turns; III: helical coil evaporator with a diameter of 50‐mm coil and four turns). From the experimental results, it can be observed that the performance of evaporator III is higher than the two other forms. A greater heat transfer coefficient value is found in case of type III evaporator and is equivalent to 2456 W/m2·°C. The maximum thermal resistance reduction occurs in the type III evaporator (37.32%), and the highest effective thermal conductivity for the same type is 6.123e + 05 W/m·°C. The experimental results demonstrate good agreement with the empirical equations.
- 31 July 2020
- Published by Wiley in Heat Transfer
- Vol. 50 (1) , 466-486
Experimental study of closed‐loop thermosyphon with a different evaporator geometry
In this study, the effect of evaporator geometry on the loop thermosyphon's heat transfer coefficient is experimentally verified by using water as a working fluid with three filling ratios (50%, 70%, 90%), constant heat input (185 W), and condenser cooling water flow rate remaining constant at 2 Lpm. Three evaporator pipes are used (I: straight; II: helical coil evaporator with a diameter of 100‐mm coil and two turns; III: helical coil evaporator with a diameter of 50‐mm coil and four turns). From the experimental results, it can be observed that the performance of evaporator III is higher than the two other forms. A greater heat transfer coefficient value is found in case of type III evaporator and is equivalent to 2456 W/m2·°C. The maximum thermal resistance reduction occurs in the type III evaporator (37.32%), and the highest effective thermal conductivity for the same type is 6.123e + 05 W/m·°C. The experimental results demonstrate good agreement with the empirical equations.
- 16 July 2020
- Published by Wiley in Heat Transfer
- Vol. 49 (8) , 4173-4203
Mixed convection of nanofluid in a square enclosure with a hot bottom wall and a conductive half‐immersed rotating circular cylinder
In this study. The mixed convection in a square enclosure with a hot bottom wall and a conductive half‐immersed rotating cylinder from its top wall is investigated numerically. The enclosure is filled with a copper‐water nanofluid. The upper half of the cylinder is cooled by the surrounding air, whereas its solid lower half is exposed to the nanofluid. The two left and right sidewalls of the enclosure, together with the remaining regions of its top wall, are assumed to be adiabatic. The dimensionless governing equations are expressed for the velocity and the temperature formulation, and they are modeled by using COMSOL code based on the Galerkin finite element method. In the present work, the geometrical aspect ratio is considered to be varied as (0.2 ≤ R/L ≤ 0.5), the thermal conductivity ratio is considered to be varied as 1 ≤ Kr ≤ 10, the angular rotational velocity is considered to be varied as 0 ≤ ≤ 1000, and the ambient convection heat transfer coefficient is considered to be varied as 5 ≤ h ≤ 20. However, the solid volume fraction (ϕ), the Prandtl number (Pr), and the Rayleigh number (Ra) are considered to be fixed at ϕ = 0.02, Pr = 6.2, and Ra = 105. It was found that the convection effect becomes more pronounced when the angular rotational velocity increases, whereas a reverse behavior is observed with an increase in the geometrical aspect ratio. Also, it was observed that the heat explorer depth begins to decrease as the angular rotational velocity increases until the increases of angular rotational velocity effect is diminishing therefore it may be the main target of the present research. This observation is seen for both considered values of the thermal conductivity ratio and the geometrical aspect ratio. Moreover, it was observed that both the local and the average Nusselt numbers increase as the geometrical aspect ratio increases. A comparison with a previously published numerical work is performed, and a good agreement between the results is observed.
- 16 July 2020
- Published by Wiley in Heat Transfer
- Vol. 49 (8) , 4173-4203
Mixed convection of nanofluid in a square enclosure with a hot bottom wall and a conductive half‐immersed rotating circular cylinder
In this study. The mixed convection in a square enclosure with a hot bottom wall and a conductive half‐immersed rotating cylinder from its top wall is investigated numerically. The enclosure is filled with a copper‐water nanofluid. The upper half of the cylinder is cooled by the surrounding air, whereas its solid lower half is exposed to the nanofluid. The two left and right sidewalls of the enclosure, together with the remaining regions of its top wall, are assumed to be adiabatic. The dimensionless governing equations are expressed for the velocity and the temperature formulation, and they are modeled by using COMSOL code based on the Galerkin finite element method. In the present work, the geometrical aspect ratio is considered to be varied as (0.2 ≤ R/L ≤ 0.5), the thermal conductivity ratio is considered to be varied as 1 ≤ Kr ≤ 10, the angular rotational velocity is considered to be varied as 0 ≤ ≤ 1000, and the ambient convection heat transfer coefficient is considered to be varied as 5 ≤ h ≤ 20. However, the solid volume fraction (ϕ), the Prandtl number (Pr), and the Rayleigh number (Ra) are considered to be fixed at ϕ = 0.02, Pr = 6.2, and Ra = 105. It was found that the convection effect becomes more pronounced when the angular rotational velocity increases, whereas a reverse behavior is observed with an increase in the geometrical aspect ratio. Also, it was observed that the heat explorer depth begins to decrease as the angular rotational velocity increases until the increases of angular rotational velocity effect is diminishing therefore it may be the main target of the present research. This observation is seen for both considered values of the thermal conductivity ratio and the geometrical aspect ratio. Moreover, it was observed that both the local and the average Nusselt numbers increase as the geometrical aspect ratio increases. A comparison with a previously published numerical work is performed, and a good agreement between the results is observed.