Sung-Min Yoon
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Sung-Min Yoon has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
Chi-Sun Hwang
Smart I/O Platform Research Department, Electronics and Telecommunications Research Institute, Daejeon, South Korea
1 shared publicationDa-Jeong Yun
Department of Advanced Materials Engineering for Information and Electronics, Kyung Hee University, Yongin, Gyeonggi-do, South Korea
1 shared publicationGi-Heon Kim
Smart I/O Platform Research Department, Electronics and Telecommunications Research Institute, Daejeon, South Korea
1 shared publicationGi-Ho Seo
Department of Advanced Materials Engineering for Information and Electronics, Kyung Hee University, Yongin, Gyeonggi-do, South Korea
1 shared publicationHan-Byeol Kang
Department of Advanced Materials Engineering for Information and Electronics, Kyung Hee University, Yongin, South Korea
1 shared publicationWon-Ho Lee
Department of Advanced Materials Engineering for Information and Electronics, Kyung Hee University, Yongin, Gyeonggi-do, South Korea
1 shared publication
Latest Publications
- 4 August 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 38 (10) , 1387-1389
Improvement in Device Performance of Vertical Thin-Film Transistors Using Atomic Layer Deposited IGZO Channel and Polyimide Spacer
Technical strategies for improving the device characteristics of the In-Ga-Zn-O (IGZO) vertical channel thin-film transistors (VTFTs) were presented and investigated. The vertical sidewall was constructed by dry-etch process and subsequently covered with IGZO, Al 2 O 3 , and AZO as active, gate insulator, and gate electrode layers by means of conformal atomic-layer-deposition. An abrupt profile and flat back-channel were achieved by employing the spin-coated polyimide (PI) spacer. The Off-current was additionally alleviated simply by cutting the area of an active layer. The fabricated IGZO VTFT using PI spacer with an “active-cut” structure exhibited an On/off ratio of 10 3 , a linear mobility of 7.1 cm 2 /Vs, and a subthreshold swing of 1.2 V/decade.
- 4 August 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 38 (10) , 1387-1389
Improvement in Device Performance of Vertical Thin-Film Transistors Using Atomic Layer Deposited IGZO Channel and Polyimide Spacer
Technical strategies for improving the device characteristics of the In-Ga-Zn-O (IGZO) vertical channel thin-film transistors (VTFTs) were presented and investigated. The vertical sidewall was constructed by dry-etch process and subsequently covered with IGZO, Al 2 O 3 , and AZO as active, gate insulator, and gate electrode layers by means of conformal atomic-layer-deposition. An abrupt profile and flat back-channel were achieved by employing the spin-coated polyimide (PI) spacer. The Off-current was additionally alleviated simply by cutting the area of an active layer. The fabricated IGZO VTFT using PI spacer with an “active-cut” structure exhibited an On/off ratio of 10 3 , a linear mobility of 7.1 cm 2 /Vs, and a subthreshold swing of 1.2 V/decade.
- 21 March 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 64 (5) , 2350-2356
Improvement in Sensing Responses to Ammonia Gas for Gas Sensors With Separately Designed Sensing Element Using ALD-Grown ZnO Nanoparticles and Read-Out Element of Top-Gate In-Ga-Zn-O Thin-Film Transistor
Ammonia (NH 3 ) gas sensors with unique oxide semiconductor thin-film transistor (TFT) configuration using ZnO nanoparticles (NPs) as gas-sensing element were fabricated and their gas-sensing responses were evaluated. The ZnO NPs composing the sensing elements were synthesized using atomic layer deposition (ALD). The optimum ALD conditions for the particle-like island-growth of ZnO were established by systematically investigating the ALD temperature and cycle conditions from 140 °C to 160 °C and from 5 to 30, respectively. Controlled devices of the sensor TFTs were prepared with different ALD conditions, in which sensing and read-out elements were designed to be physically separated. This unique device configuration provided us both benefits of improvement in gas-sensing property and stability of the device characteristics. The device showed instant gas responses as well as stable device behaviors at different operating temperature even with repeated gas measurements. Sufficiently good response to NH3 were obtained at 150 °C, which was significantly lower than the operating temperature of previously reported NH3 gas sensors. Based on the results the combination of novel TFT configuration and ALD-prepared ZnO NPs could be an effective method for the improvement in device characteristics of the gas sensors.
- 21 March 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 64 (5) , 2350-2356
Improvement in Sensing Responses to Ammonia Gas for Gas Sensors With Separately Designed Sensing Element Using ALD-Grown ZnO Nanoparticles and Read-Out Element of Top-Gate In-Ga-Zn-O Thin-Film Transistor
Ammonia (NH 3 ) gas sensors with unique oxide semiconductor thin-film transistor (TFT) configuration using ZnO nanoparticles (NPs) as gas-sensing element were fabricated and their gas-sensing responses were evaluated. The ZnO NPs composing the sensing elements were synthesized using atomic layer deposition (ALD). The optimum ALD conditions for the particle-like island-growth of ZnO were established by systematically investigating the ALD temperature and cycle conditions from 140 °C to 160 °C and from 5 to 30, respectively. Controlled devices of the sensor TFTs were prepared with different ALD conditions, in which sensing and read-out elements were designed to be physically separated. This unique device configuration provided us both benefits of improvement in gas-sensing property and stability of the device characteristics. The device showed instant gas responses as well as stable device behaviors at different operating temperature even with repeated gas measurements. Sufficiently good response to NH3 were obtained at 150 °C, which was significantly lower than the operating temperature of previously reported NH3 gas sensors. Based on the results the combination of novel TFT configuration and ALD-prepared ZnO NPs could be an effective method for the improvement in device characteristics of the gas sensors.