Nerea Rodriguez Rodriguez
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Nerea Rodriguez Rodriguez has a total of 49 co-authors. Here are the top co-authors by number of shared publications:
- Koen Binnemans
KU Leuven, Department of Chemistry, Solvomet Group, Celestijnenlaan 200F, box 2404, B-3001 Leuven, Belgium
9 shared publications - Maaike C. Kroon
Chemical Engineering Department, Khalifa University of Science and Technology, P.O. Box 127788, Abu Dhabi, United Arab Emirates
6 shared publications Maaike C. Kroon
5 shared publicationsCor J. Peters
3 shared publications- Martin van Sint Annaland
Eindhoven University of Technology
3 shared publications - Bieke Onghena
Department of Chemistry, KU Leuven, Celestijnenlaan 200F, P.O. Box 2404, B-3001 Leuven, Belgium
2 shared publications
Latest Publications
- 14 December 2021
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 61 (1) , 684-693
Combined Hydro–Solvo–Bioleaching Approach toward the Valorization of a Sulfidic Copper Mine Tailing
- 14 December 2021
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 61 (1) , 684-693
Combined Hydro–Solvo–Bioleaching Approach toward the Valorization of a Sulfidic Copper Mine Tailing
- 12 July 2021
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 60 (28) , 10319-10326
Integrated Process for Recovery of Rare-Earth Elements from Lamp Phosphor Waste Using Methanesulfonic Acid
- 12 July 2021
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 60 (28) , 10319-10326
Integrated Process for Recovery of Rare-Earth Elements from Lamp Phosphor Waste Using Methanesulfonic Acid
- Open Access
- 9 March 2021
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 11 (17) , 10110-10120
Dissolution behavior of precious metals and selective palladium leaching from spent automotive catalysts by trihalide ionic liquids
The dissolution behavior of the precious metals gold, platinum, rhodium and palladium in the trihexyl(tetradecyl)phosphonium trihalide ionic liquids [P66614][Cl3], [P66614][Br3], [P66614][IBr2] and [P66614][I3] was investigated. The highest dissolution rates were observed for the trichloride ionic liquid [P66614][Cl3] and this system was investigated in more detail. The effects of the trichloride concentration in the ionic liquid and temperature were studied, reaching higher leaching rates at higher trichloride conversions and increased temperatures. The stability of the trichloride anion at these elevated temperatures was studied by Raman spectroscopy. It was found that the trichloride anion decomposed during leaching at higher temperatures, showing the requirement to store these reactive compounds in sealed and cool environments, shielded from light. The optimal leaching conditions were applied for the recovery of palladium from ceramic monolith powder, obtained from end-of-life automotive catalysts. The catalyst powder was contacted with the ionic liquid [P66614][Cl3] and the metal concentrations in the ionic liquid were monitored. The trihalide ionic liquid allowed a more selective leaching of palladium compared to other metals present at very high concentrations in the monolith structure, like magnesium. The relative ratio of palladium over magnesium increased by two orders of magnitude compared to the original catalyst composition. The effect of the contact time between the catalyst powder and the ionic liquid on the metal concentrations in the leachate was investigated, but no significant improvement in the selectivity was observed.
- 9 March 2021
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 11 (17) , 10110-10120
Open AccessDissolution behavior of precious metals and selective palladium leaching from spent automotive catalysts by trihalide ionic liquids
The dissolution behavior of the precious metals gold, platinum, rhodium and palladium in the trihexyl(tetradecyl)phosphonium trihalide ionic liquids [P66614][Cl3], [P66614][Br3], [P66614][IBr2] and [P66614][I3] was investigated. The highest dissolution rates were observed for the trichloride ionic liquid [P66614][Cl3] and this system was investigated in more detail. The effects of the trichloride concentration in the ionic liquid and temperature were studied, reaching higher leaching rates at higher trichloride conversions and increased temperatures. The stability of the trichloride anion at these elevated temperatures was studied by Raman spectroscopy. It was found that the trichloride anion decomposed during leaching at higher temperatures, showing the requirement to store these reactive compounds in sealed and cool environments, shielded from light. The optimal leaching conditions were applied for the recovery of palladium from ceramic monolith powder, obtained from end-of-life automotive catalysts. The catalyst powder was contacted with the ionic liquid [P66614][Cl3] and the metal concentrations in the ionic liquid were monitored. The trihalide ionic liquid allowed a more selective leaching of palladium compared to other metals present at very high concentrations in the monolith structure, like magnesium. The relative ratio of palladium over magnesium increased by two orders of magnitude compared to the original catalyst composition. The effect of the contact time between the catalyst powder and the ionic liquid on the metal concentrations in the leachate was investigated, but no significant improvement in the selectivity was observed.
- Open Access
- 9 November 2020
- Published by Springer Nature in Journal of Sustainable Metallurgy
- Vol. 6 (4) , 680-690
Selective Removal of Zinc from BOF Sludge by Leaching with Mixtures of Ammonia and Ammonium Carbonate
The zinc content of basic oxygen furnace (BOF) sludges is too high for direct recycling into the blast furnace via the sinter plant, as excessive zinc concentrations are detrimental for the refractory lining of the blast furnace. However, by partial and selective removal of zinc from the BOF sludge, the residual sludge can be used as a secondary iron resource in the blast furnace. In this paper, BOF sludge was leached with aqueous ammonia, aqueous solutions of ammonium salts (chloride, carbonate, and sulfate), and aqueous mixtures of ammonia and ammonium salt. The mixtures of ammonia and ammonium salt could leach more zinc with respect to either the aqueous ammonia or the aqueous ammonium salt solution. The ammonia–ammonium carbonate (AAC) mixture was selected as the most suitable lixiviant due to the high zinc leaching efficiency in combination with a high selectivity towards iron; furthermore, this combination does not introduce unwanted chloride or sulfate impurities in the residue. The leaching process was optimized in terms of the liquid-to-solid ratio, total ammonia concentration, ammonium:ammonia molar ratio, temperature, and leaching time. The co-dissolved iron was precipitated as a hydroxide after oxidation of ferrous to ferric ions by an air stream, without co-precipitation of zinc, while the dissolved zinc could be easily recovered as zinc sulfide by precipitation with ammonium sulfide. The (almost) closed-loop process was successfully up-scaled from 10 mL to 1 L scale. Graphical
- 9 November 2020
- Published by Springer Nature in Journal of Sustainable Metallurgy
- Vol. 6 (4) , 680-690
Open AccessSelective Removal of Zinc from BOF Sludge by Leaching with Mixtures of Ammonia and Ammonium Carbonate
The zinc content of basic oxygen furnace (BOF) sludges is too high for direct recycling into the blast furnace via the sinter plant, as excessive zinc concentrations are detrimental for the refractory lining of the blast furnace. However, by partial and selective removal of zinc from the BOF sludge, the residual sludge can be used as a secondary iron resource in the blast furnace. In this paper, BOF sludge was leached with aqueous ammonia, aqueous solutions of ammonium salts (chloride, carbonate, and sulfate), and aqueous mixtures of ammonia and ammonium salt. The mixtures of ammonia and ammonium salt could leach more zinc with respect to either the aqueous ammonia or the aqueous ammonium salt solution. The ammonia–ammonium carbonate (AAC) mixture was selected as the most suitable lixiviant due to the high zinc leaching efficiency in combination with a high selectivity towards iron; furthermore, this combination does not introduce unwanted chloride or sulfate impurities in the residue. The leaching process was optimized in terms of the liquid-to-solid ratio, total ammonia concentration, ammonium:ammonia molar ratio, temperature, and leaching time. The co-dissolved iron was precipitated as a hydroxide after oxidation of ferrous to ferric ions by an air stream, without co-precipitation of zinc, while the dissolved zinc could be easily recovered as zinc sulfide by precipitation with ammonium sulfide. The (almost) closed-loop process was successfully up-scaled from 10 mL to 1 L scale. Graphical
- Open Access
- 4 August 2020
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 10 (48) , 28879-28890
Recovery of yttrium and europium from spent fluorescent lamps using pure levulinic acid and the deep eutectic solvent levulinic acid–choline chloride
A solvometallurgical approach for the recovery of rare-earth elements from lamp phosphor waste was developed. The solubility of individual phosphors in different deep-eutectic solvents (DESs) was measured. The DES levulinic acid–choline chloride (xChCl = 0.33) showed high solubility of the YOX phosphor (Y2O3:Eu3+) and low solubility of the HALO phosphor (Sr,Ca)10(PO4)(Cl,F)2:Sb3+,Mn2+, which does not contain any rare-earth element. This DES was selected for further investigation. When the DES was compared to pure levulinic acid, very similar leaching behaviour was observed, showing that the proton activity is more important than the chloride as a metal ligand. The leaching of YOX and HALO using levulinic acid–choline chloride (xChCl = 0.33) or pure levulinic acid was optimised in terms of water content, temperature and leaching time. The optimised parameters were validated in a synthetic mixture of phosphors and in real lamp phosphor waste. The co-dissolution of HALO is higher in the real waste than in the synthetic mixture. The real waste was also leached with an aqueous solution of hydrochloric acid, which was non-selective against dissolution of YOX, and with the functionalised ionic liquid betainium bis(trifluoromethylsulfonyl)imide. The ionic liquid gave a similar selectivity as levulinic acid, but is much more expensive. The recovery of the metals from the pregnant leach solution was tested via precipitation with oxalic acid and solvent extraction. Oxalic acid precipitation was not suitable for the DES system. The metals could be extracted via solvent extraction with the acidic extractant bis(2-ethylhexyl)phosphoric acid (D2EHPA) and stripped by an aqueous hydrochloric acid solution. Pure levulinic acid was found to be more suitable than the corresponding ChCl-based DES for the selective recovery of YOX.
- 4 August 2020
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 10 (48) , 28879-28890
Open AccessRecovery of yttrium and europium from spent fluorescent lamps using pure levulinic acid and the deep eutectic solvent levulinic acid–choline chloride
A solvometallurgical approach for the recovery of rare-earth elements from lamp phosphor waste was developed. The solubility of individual phosphors in different deep-eutectic solvents (DESs) was measured. The DES levulinic acid–choline chloride (xChCl = 0.33) showed high solubility of the YOX phosphor (Y2O3:Eu3+) and low solubility of the HALO phosphor (Sr,Ca)10(PO4)(Cl,F)2:Sb3+,Mn2+, which does not contain any rare-earth element. This DES was selected for further investigation. When the DES was compared to pure levulinic acid, very similar leaching behaviour was observed, showing that the proton activity is more important than the chloride as a metal ligand. The leaching of YOX and HALO using levulinic acid–choline chloride (xChCl = 0.33) or pure levulinic acid was optimised in terms of water content, temperature and leaching time. The optimised parameters were validated in a synthetic mixture of phosphors and in real lamp phosphor waste. The co-dissolution of HALO is higher in the real waste than in the synthetic mixture. The real waste was also leached with an aqueous solution of hydrochloric acid, which was non-selective against dissolution of YOX, and with the functionalised ionic liquid betainium bis(trifluoromethylsulfonyl)imide. The ionic liquid gave a similar selectivity as levulinic acid, but is much more expensive. The recovery of the metals from the pregnant leach solution was tested via precipitation with oxalic acid and solvent extraction. Oxalic acid precipitation was not suitable for the DES system. The metals could be extracted via solvent extraction with the acidic extractant bis(2-ethylhexyl)phosphoric acid (D2EHPA) and stripped by an aqueous hydrochloric acid solution. Pure levulinic acid was found to be more suitable than the corresponding ChCl-based DES for the selective recovery of YOX.
- Open Access
- 19 February 2020
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 10 (12) , 7328-7335
Selective recovery of zinc from goethite residue in the zinc industry using deep-eutectic solvents
Several deep-eutectic solvents (DESs) were tested for the valorisation of goethite residue produced by the zinc industry. The objective of the work was to selectively recover zinc from the iron-rich matrix using deep-eutectic solvents as lixiviants. The effect of the type of hydrogen bond donor and hydrogen bond acceptor of the deep-eutectic solvent on the leaching efficiency was studied. Levulinic acid–choline chloride (xChCl = 0.33) (LevA–ChCl) could selectively leach zinc from the iron-rich matrix, and it was selected as the best-performing system to be used in further study. The leaching process was optimised in terms of temperature, contact time, liquid-to-solid ratio and water content of the deep-eutectic solvent. The role of the choline cation on the leaching process was investigated by considering the leaching properties of a LevA–CaCl2 mixture. The goethite residue was also leached with pure levulinic acid. The results were compared to a purely hydrometallurgical approach using sulphuric acid leaching. Leaching with LevA–ChCl resulted in higher selectivity compared to the conventional “hot leaching” with 80 g L−1 sulphuric acid. Furthermore, a slightly higher zinc recovery and comparable selectivity for zinc over iron were achieved with LevA–ChCl compared to conventional “neutral leaching” with 10 g L−1 sulphuric acid.
- 19 February 2020
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 10 (12) , 7328-7335
Open AccessSelective recovery of zinc from goethite residue in the zinc industry using deep-eutectic solvents
Several deep-eutectic solvents (DESs) were tested for the valorisation of goethite residue produced by the zinc industry. The objective of the work was to selectively recover zinc from the iron-rich matrix using deep-eutectic solvents as lixiviants. The effect of the type of hydrogen bond donor and hydrogen bond acceptor of the deep-eutectic solvent on the leaching efficiency was studied. Levulinic acid–choline chloride (xChCl = 0.33) (LevA–ChCl) could selectively leach zinc from the iron-rich matrix, and it was selected as the best-performing system to be used in further study. The leaching process was optimised in terms of temperature, contact time, liquid-to-solid ratio and water content of the deep-eutectic solvent. The role of the choline cation on the leaching process was investigated by considering the leaching properties of a LevA–CaCl2 mixture. The goethite residue was also leached with pure levulinic acid. The results were compared to a purely hydrometallurgical approach using sulphuric acid leaching. Leaching with LevA–ChCl resulted in higher selectivity compared to the conventional “hot leaching” with 80 g L−1 sulphuric acid. Furthermore, a slightly higher zinc recovery and comparable selectivity for zinc over iron were achieved with LevA–ChCl compared to conventional “neutral leaching” with 10 g L−1 sulphuric acid.
- Open Access
- 12 November 2019
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 7 (24) , 19807-19815
Recovery of Lead and Silver from Zinc Leaching Residue Using Methanesulfonic Acid
A solvometallurgical route for the recovery of lead and silver from the leaching residue of the zinc roast-leach-electrowin process was developed. Methanesulfonic acid was selected as lixiviant due to the high solubility of lead and silver methanesulfonate salts. The direct leaching of the residue with methanesulfonic acid showed a high co-dissolution of gypsum and a low dissolution of lead (present as anglesite), requiring a high liquid-to-solid ratio. Two pretreatment processes were investigated to improve the leaching efficiency. First, the gypsum was selectively removed via Randall extraction using water as a solvent. Pure gypsum was obtained in this step, and the solvent could be reused multiple times. Secondly, the solubility of lead was increased by transforming the anglesite into cerussite via a carbonation reaction with sodium carbonate. When the carbonation reaction was performed before the removal of gypsum, a significant excess of sodium carbonate was required, because the gypsum was also transformed into calcium carbonate. However, when the carbonation was done on the gypsum-free material, a stoichiometric amount of sodium carbonate was sufficient. The carbonation reaction drastically increased the lead dissolution, and the liquid-to-solid ratio requirements decreased. The leaching efficiency for both silver and lead using methanesulfonic acid as lixiviant after Randall extraction and the carbonation reaction was around 80%.
- 12 November 2019
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 7 (24) , 19807-19815
Open AccessRecovery of Lead and Silver from Zinc Leaching Residue Using Methanesulfonic Acid
A solvometallurgical route for the recovery of lead and silver from the leaching residue of the zinc roast-leach-electrowin process was developed. Methanesulfonic acid was selected as lixiviant due to the high solubility of lead and silver methanesulfonate salts. The direct leaching of the residue with methanesulfonic acid showed a high co-dissolution of gypsum and a low dissolution of lead (present as anglesite), requiring a high liquid-to-solid ratio. Two pretreatment processes were investigated to improve the leaching efficiency. First, the gypsum was selectively removed via Randall extraction using water as a solvent. Pure gypsum was obtained in this step, and the solvent could be reused multiple times. Secondly, the solubility of lead was increased by transforming the anglesite into cerussite via a carbonation reaction with sodium carbonate. When the carbonation reaction was performed before the removal of gypsum, a significant excess of sodium carbonate was required, because the gypsum was also transformed into calcium carbonate. However, when the carbonation was done on the gypsum-free material, a stoichiometric amount of sodium carbonate was sufficient. The carbonation reaction drastically increased the lead dissolution, and the liquid-to-solid ratio requirements decreased. The leaching efficiency for both silver and lead using methanesulfonic acid as lixiviant after Randall extraction and the carbonation reaction was around 80%.
- Top Cited Papers
- 28 May 2019
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 7 (13) , 11521-11528
Degradation of Deep-Eutectic Solvents Based on Choline Chloride and Carboxylic Acids
- 28 May 2019
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 7 (13) , 11521-11528
Top Cited PapersDegradation of Deep-Eutectic Solvents Based on Choline Chloride and Carboxylic Acids
- 22 January 2019
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 7 (4) , 3940-3948
p-Toluenesulfonic Acid-Based Deep-Eutectic Solvents for Solubilizing Metal Oxides
- 22 January 2019
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 7 (4) , 3940-3948
p-Toluenesulfonic Acid-Based Deep-Eutectic Solvents for Solubilizing Metal Oxides