PPPrajof Prabhakaran

Prajof Prabhakaran

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Prajof Prabhakaran has a total of 26 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Soft-Switching Bidirectional Converter for Electric Vehicle Power Interfaces

    by Veera Venkata Subrahmanya Kumar Bhajana, Pravat Biswal, Vivek Kumar, Prajof Prabhakaran

    This article proposes a bidirectional buck–boost converter for electric vehicle (EV) charging applications, featuring a single-auxiliary switch to achieve zero-voltage switching (ZVS) and enhanced efficiency across a wide operating range. The auxiliary network, composed of a resonant inductor, capacitor, and diodes, enables ZVS in both buck and boost modes regardless of load, duty cycle, or power direction. The converter operates in continuous conduction mode on the low-voltage side with constant-frequency pulsewidth modulation (PWM) control. All switches benefit from soft-switching under light and heavy load conditions. The topology preserves voltage and current stress on the main switch while reducing switching losses and component count. Theoretical analysis, dynamic modeling, and experimental validation using a 48-/160-V, 200-W prototype confirm the effectiveness of the proposed approach.


  • Design and Analysis of a Three-Port Bidirectional DC–DC Converter with Low Voltage Stress and Flexible Power Flow Control for DC Microgrid Applications

    by Sunil Mandal, Prajof Prabhakaran

    Non-isolated bidirectional dc–dc converters (BDCs) are widely used for power flow management in energy storage systems, dc microgrids (DC-MGs), and electric vehicles (EVs); however, many existing topologies suffer from limited voltage gain, narrow duty-cycle range, high component count, bulky structure, and high voltage stress on power devices. To overcome these limitations, this paper proposes a non-isolated three-port high-gain bidirectional dc–dc converter for the integration of renewable energy sources, energy storage units, and DCMGs. The proposed converter supports multiple power flow paths, including battery-to-DC-MG, photovoltaics (PV)-to-DC-MG, and DC-MG-to-battery operation. It operates in boost mode for power transfer from Port A to Port B and in buck mode for reverse power flow. A wide voltage conversion ratio with reduced voltage stress across most switches is achieved, improving efficiency and reliability. A 200-W SiC MOSFET–based prototype is developed and experimentally validated. The converter achieves a peak efficiency of 96% and exhibits stable operation under both open-loop and closed-loop control. Operation in both continuous and discontinuous conduction modes further demonstrates the flexibility and robustness of the proposed topology.

  • A Three-Port Bidirectional DC–DC Converter with Wide Voltage Conversion and Flexible Power Flow Control for DC Microgrid Applications

    by Sunil Mandal, Prajof Prabhakaran

    Non-isolated bidirectional DC-DC converters (BDCs) are essential for efficient power flow management in energy storage systems, DC microgrids (DC-MGs), electric vehicles (EVs), and industrial electronics applications. However, most existing topologies are limited by narrow duty cycle ranges, high component counts, increased cost, bulky structures, and elevated voltage stress while achieving the required voltage gain. To address these issues, this paper presents a three-port non-isolated high-gain BDC designed for renewable energy, energy storage, and DC-MG integration. The proposed converter supports multiple power flow paths, including battery-to-DC-MG, photovoltaic (PV)-to-both battery and DC-MG, PV-to-DC-MG, and DC-MG-to-battery. It operates in boost mode during power transfer from the PV source to the battery and DC-MG, and from the battery to the DC-MG, while functioning in buck mode when power flows from the DC-MG to the battery. The topology achieves a wide voltage conversion ratio with low voltage stress across most switches, improving both efficiency and reliability. A 200 W experimental prototype employing SiC MOSFETs was developed and tested. The converter demonstrated stable operation under both open-loop and closed-loop modes, achieving a peak experimental efficiency of 95.8%. Furthermore, it can operate in continuous (CCM) and discontinuous conduction modes (DCM), confirming its flexibility and robustness under varying conditions.

  • A Multi-Input Non-Isolated High-Gain Bidirectional DC–DC Based on an Improved SEPIC Topology for DC Grid Integration

    by Sunil Mandal, Prajof Prabhakaran, Megha Rajagopal

    This paper presents a novel transformerless bidirectional buck–boost (BBB) high-gain DC–DC converter with multi-power-flow capability. The proposed topology integrates an active switched-inductor (ASL) network into the front-end of a conventional SEPIC converter, enabling a wide voltage conversion ratio while significantly reducing the voltage stress across the main power semiconductor devices. The converter supports BBB operation in both directions of power flow with a reduced component count. A key feature of the proposed converter is its multifunctional operation, allowing seamless power transfer in PV-to-DC-grid, battery-to-DC-grid, and DC-grid-to-battery modes. In addition, synchronous rectification is employed in the complementary switches to further enhance conversion efficiency. The converter’s operational principles are analysed with detailed steady-state derivations for continuous conduction mode (CCM) and discontinuous conduction mode (DCM). A dynamic model is developed, and closed-loop controllers are designed for voltage and current regulation. A prototype employing SiC MOSFETs is developed and tested. Experimental results confirm high efficiency, stable operation, and practical feasibility, demonstrating the converter’s potential for energy storage applications in microgrids, electric vehicles (EVs), and industrial power systems.


  • A High-Efficiency, High-Gain, Non-Isolated Bidirectional DC–DC Converter for Interfacing DC Grid-Connected Energy Storage Systems

    by Sunil Mandal, Prajof Prabhakaran

    Non-isolated, high-gain, bidirectional DC-DC converters (BDCs) are essential for efficient power flow control in energy storage systems deployed in microgrids, electric vehicles (EVs), and other industrial power conversion applications. However, existing converter topologies are often limited by narrow duty cycle ranges, high component counts, and significant voltage stress in achieving the required voltage gain. This paper proposes a non-coupled, high-gain bidirectional DC-DC converter designed to address these limitations. The proposed converter operates boost mode in one power flow direction and buck mode in reverse power flow direction, optimizing performance across a wider range of operating conditions. The converter’s design is based on the integration of a modified bidirectional SEPIC converter topology with an active switched inductor (ASL) at the front end. This results in a simplified circuit architecture and control strategy, requiring fewer components while effectively minimizing voltage stress on most switches. Additionally, SiC MOSFET is implemented to enhance the efficiency of the proposed topology. The converter is rated for 250 W, and a prototype was developed and tested in the laboratory. The experimental setup demonstrated a peak efficiency of 97.78%, validating the converter’s performance. The results confirm that the converter is well-suited for both open-loop and closed-loop control configurations, demonstrating its potential for a wide array of applications.


  • A Novel Nonisolated Three-Port BBB DC–DC Converter for Multifunctional PV, Battery, and DC Grid Interfacing Applications

    by Sunil Mandal, Prajof Prabhakaran, Shreyas S Aney

    This article presents a novel nonisolated bidirectional buck–boost dc–dc converter without employing a transformer or coupled inductor. An active switched inductor network is integrated into the front-end section of a modified SEPIC converter, facilitating a wide voltage conversion ratio while reducing voltage stress on the major switches. The proposed converter offers multifunctional capabilities, enabling seamless integration with photovoltaic (PV) systems, battery storage, and dc grids. The battery can be charged either from the PV system or directly from the dc grid, enhancing system flexibility. Furthermore, synchronous rectification is implemented using complementary switching to improve conversion efficiency. The steady-state analysis is presented for both continuous conduction mode and discontinuous conduction mode. A dynamic model of the converter is developed, and its performance is validated under both open-loop and closed-loop conditions using SiC mosfets. Experimental results verify the enhanced performance and practicality of the proposed converter for energy storage systems in dc grids, electric vehicles, and other industrial power conversion applications.

  • A Novel Boost Derived Input-Parallel Output-Series DC-DC Converter for Bipolar DC Nanogrid

    by Sourav Prasad, Sunil Mandal, Prajof Prabhakaran, Arun Dominic

    While bipolar configurations in DC nanogrids offer numerous advantages, they typically rely on a substantial number of standalone DC-DC converters to supply power to both poles of the grid. Furthermore, voltage imbalances frequently occur due to unequal load distribution between the poles. To address these challenges, this paper describes a novel Input Parallel Output Series Boost-Cuk (IPOSBC) converter that transfers energy from a single source to both poles, effectively reducing the overall converter count in the DC nanogrid system. The proposed converter features an interleaved structure that minimizes source current ripple, delivers a bipolar output with enhanced voltage gain, and achieves zero-voltage switching for two switches, thereby improving overall efficiency. Additionally, the paper presents a unique voltage imbalance mitigation strategy that leverages the proposed converter's bidirectional operation. In this approach, the converter absorbs the neutral line current and redistributes it equally between the positive and negative poles of the bipolar DC nanogrid, balancing the pole voltages without the need for an active power source connected to its input terminals. This reduction in neutral line current also decreases the overall line losses in the nanogrid system. The feasibility and effectiveness of these techniques are validated through theoretical analysis and experimental results from a 250W hardware prototype of the IPOSBC converter.


  • Open Access

    A Transformerless Bidirectional Active Switched Inductor-Based SEPIC High-Gain DC–DC Converter With Buck–Boost Capability

    by Sunil Mandal, Prajof Prabhakaran, D. Arun Dominic, Arun P. Parameswaran

    The growing demand for efficient and compact power conversion systems in electric vehicles (EVs), renewable energy systems, DC microgrids, and both portable and stationary medical equipment has intensified research into non-isolated high-gain bidirectional DC-DC converters. Existing solutions often employ transformer-based topologies or coupled inductors, which introduce increased cost, size, and control complexity. This paper presents a novel transformerless bidirectional high-gain DC-DC converter based on a modified Single-Ended Primary Inductor Converter (SEPIC) architecture. The proposed topology incorporates an Active Switched Inductor (ASL) at the input stage to achieve a wide voltage conversion ratio while ensuring reduced voltage stress on the maximum power switches. A key feature of the converter is its ability to provide bidirectional buck–boost operation in both power flow directions, while maintaining a reduced component count and improved efficiency through synchronous rectification. The converter’s performance is thoroughly analyzed under both continuous conduction mode (CCM) and discontinuous conduction mode (DCM). Furthermore, detailed small-signal modeling and closed-loop controller design are developed for both voltage-mode and current-mode control. A 200 W experimental prototype employing SiC MOSFETs is implemented to validate the theoretical analysis. Experimental results confirm the high efficiency, robust dynamic response, and practical feasibility of the proposed converter for next-generation power conversion applications.


  • Open Access

    An Integrated Onboard EV Charger With Wide Voltage Range Compatibility

    by Vivek Kumar, Prajof Prabhakaran, B. Dastagiri Reddy, J. L. Febin Daya

    Electric vehicles (EVs) typically employ separate onboard chargers and traction inverters for battery charging and motor operation, respectively. This paper proposes a bidirectional integrated onboard charger (BIOC) that utilizes a single power converter to perform both functions, thereby reducing cost, improving system compactness, and supporting fast charging. The proposed BIOC architecture is implemented using a totem-pole power factor correction (PFC) stage combined with an additional coupling unit. This configuration supports a wide range of battery voltages and is compatible with both AC and DC grid inputs. The BIOC incorporates active power decoupling (APD) to minimize voltage ripple at the battery terminals during high-voltage (HV) battery charging. Leakage current analysis of the totem-pole PFC stage confirms compliance with safety standards, and a detailed switch loss calculation procedure is presented. A comprehensive controller design is developed using State-Space Averaging (SSA) and Small Signal Modelling (SSM), followed by a K-factor method to ensure optimal performance across various operating modes. The proposed system is validated through simulations on a 2 kW Simulink model and experimental testing on a 400 W scaled-down prototype, demonstrating effective charging of an EV battery across a wide voltage range from both AC and DC grids. This work offers a unified, efficient, and cost-effective solution for integrated onboard EV charging.


  • A Novel Bidirectional Modified Zeta Converter With Wide Voltage Conversion Ratio

    by Sunil Mandal, Prajof Prabhakaran

    High-gain, non-isolated bidirectional DC-DC converters play a vital role in interfacing energy storage systems with microgrids and electric vehicles. However, existing converters often operate within a limited duty cycle range and involve high component counts and significant voltage stress for achieving desired voltage gains. This paper presents a novel non-coupled high-gain bidirectional DC-DC converter that efficiently operates in boost mode for forward power flow and buck mode for reverse power flow. Based on a modified Zeta converter topology, the proposed converter offers a simplified circuit structure and control strategy, requiring fewer components. It achieves wide voltage gain across an extended duty cycle range while minimizing voltage stress on most switches. A 200 W prototype has been developed and tested in the laboratory to validate the converter’s performance. To enhance efficiency, SiC MOSFETs are utilized, achieving a peak efficiency of 96%. Experimental results confirm the converter’s suitability for both open-loop and closed-loop configurations, highlighting its potential for diverse applications in energy storage systems and electric vehicles.