Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Reuben A. Govender has a total of 49 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Case Study: Development of a Biaxial Tensile Testing Machine for Soft Materials and Biological Tissues

    by Reuben A. Govender, Jonathan A. Caine

    While uniaxial tensile testing machines are ubiquitous, very few local institutions have access to biaxial tensile testing facilities, and even fewer have machines suited for low-force applications such as elastomers or biological tissues. This case study reports on the design of a custom planar biaxial tensile testing machine, which functioned as a stand-alone desktop tensile tester with two independent, orthogonal testing axes to facilitate the investigation of soft biological materials. Two 50N load cells were used to measure load, and a non-contact Digital Image Correlation system was used to measure three-dimensional surface displacement. Commissioning testing was performed using a silicone elastomer (Smooth-On, Dragon Skin 10) which served as a surrogate for skin. The testing did not seek to characterise the surrogate material, but to verify that the machine operated as intended. Tensile specimens were tested on the custom machine and a commercial tensile testing machine for comparison at four crosshead displacement rates: 10,50,120 and 400mmmin−1. Planar biaxial tensile testing was then performed on cruciform Dragon Skin 10 specimens at the same speeds, but at different speed ratios between the testing axes. The performance of the custom-built machine was critically assessed, and the areas of difficulty encountered during testing were handling and gripping highly pliable specimens, maintaining consistent specimen boundary conditions, and ensuring alignment. The testing demonstrated that the machine functioned as intended and met the requirements for use in testing skin and other membrane tissues in the future.

  • Open Access

    Building Towards Better Learning

    by Reuben Govender, Adriaan De Villiers

    We describe the iteration of a practical design and prototype testing activity in our 2nd year Mechanical Design course. The initial implementation was a low complexity, low risk design task where only FDM 3D printing was used for manufacturing a static structural part. Subsequent implementations involved more complex design tasks, where prototypes required moving machine elements, and the manufacturing “toolkit” expanded to include LASER cutting and carpentry tools. We discuss challenges encountered, either due to logistical difficulties or poor estimation of student preparedness for workshop tasks. Our students have embraced the experience and we intend to retain this activity, noting some logistical and scheduling improvements that will facilitate future iterations.

  • Open Access

    A Novel Striker Configuration for Tensile Split Hopkinson Bar Testing with Dynamic Specimen Recovery

    by M. R. Thomas, R. A. Govender, T. J. Cloete

    The split Hopkinson pressure bar (SHPB) is widely used for acquiring high strain rate (HSR) material data. For purposes of exhaustive characterisation, HSR data are required to assess strain rate sensitivity. A notable limitation of a conventional SHPB lies in the control of a test specimen’s ultimate deformation, because specimens are typically subjected to an unknown number of repeated loading events. For this reason, microstructural investigations on SHPB specimens hold little value, as the final specimen state does not correlate with the recorded loading event. In this paper, a tensile split Hopkinson bar (TSHB) arrangement designed to conduct interruptible tests is presented. This includes a pull-off tensile striker and tandem momentum traps in a novel configuration, which allows the input bar to remain supported over its entire length while eliminating the need for precise gap setting between pressure bars and momentum traps, or striker speed control. In addition, a fir-tree tensile specimen fixture design was utilised to secure the specimen to the bars. Results from a series of experiments on DOMEX 550 specimens are presented to demonstrate the effectiveness of the TSHB configuration. Loading histories inferred from strain gauge data are compared to the measured lengths of recovered specimens as verification of the ability of this apparatus to conduct interruptible tests. In addition, tests are compared to those conducted without interruption under the same testing conditions, further demonstrating the capability of this system.


  • Open Access

    The Application of Taguchi Experiments in Developing Gecko-Inspired Dry Adhesive for Macro-Handling Applications

    by L. Nyanga, R.A. Govender, S. Matope

    Synthetic dry adhesives have been developed to mimic the gecko’s adhesion using lithography and micro-machining of a mould to cast a suitable elastomer. Previous international studies used nano-manufacturing processes, which are expensive and are not readily available in South Africa. In this study, a simple micro-machining method was used using a three-axis milling machine and Vytaflex 30 to develop an adhesive pad. The Taguchi method to design experiments was used to determine the optimum machining conditions to create micro-wedges. The results show that, although a maximum adhesion pressure of 1,924 Pa was obtained with a preload pressure of 1,323 Pa, the adhesion force produced might not be suitable for macro-handling applications.

  • Open Access

    Development of a Prototype Embedded 3D Printer with Dual Ink-Gel Extrusion Capability

    by A. Van Driel, R.A. R.A. Govender

    3D printing has advanced significantly, enabling new applications such as embedded 3D printing for materials that solidify slowly. This method prints liquid materials into a support gel that holds their shape while curing. This project developed the dual ink-gel extruder (DIGEX) to address the limitations in the print volume seen in previous projects and to enable the simultaneous extrusion of material and support gel. Various sub-assemblies and deposition techniques were tested to optimise performance. While DIGEX successfully demonstrated the concept, difficulties remain in scaling for large-format printing, requiring further refinement in hardware, software, and process configurations.

  • Open Access

    The Effect of Scaling Building Configuration Blast Experiments on Positive Phase Blast Wave Parameters

    by Sherlyn Gabriel, Jack Denny, Steeve Chung Kim Yuen, Genevieve S. Langdon, Reuben A. Govender

    Explosions in an urban setting can have a significant negative impact. There is a need to further understand the loading effects caused by the blast’s interaction with structures. In conjunction with this, the effects of scaling and understanding the limitations of laboratory experiments are equally important given the cost incurred for full-scale experiments. The aim of this study was to determine the scaling effects on blast wave parameters found for reduced-scale urban blast scenario laboratory experiments. This paper presents the results of numerical modelling and physical experiments on detonating cuboidal PE-4 charges and measuring the pressure in direct line of sight and at three distinct positions around the corner of a small-scale “building” parallel to the rear wall. Two scales were used, namely 75% and 100%. Inter-scaling between 75% and 100% worked fairly well for positions shielded by the corner of the wall. Additionally, the lab-scale results were compared to similar (but not identical) field trials at an equivalent scale of 250%. The comparison between lab-scale idealised testing and the larger-scale field trials published by Gajewksi and Sielicki in 2020, indicated sensitivity to factors such as detonator positioning, explosive material, charge confinement/mounting, building surface roughness, and environment.


  • Round-Robin test of split Hopkinson pressure bar

    by Muhammad A. Kariem, Rafael C. Santiago, Reuben Govender, Dong Wei Shu, Dong Ruan, Gerald Nurick, Marcilio Alves, Guoxing Lu, Genevieve S. Langdon


  • Open Access

    Developing a 3D mineral texture quantification method of drill core for geometallurgy

    by M.J. Voigt, J. Miller, L. Bbosa, R.A. Govender, D. Bradshaw, A. Mainza, M. Becker

    Mineral texture is a critical factor which controls ore variability and is an important attribute in geometallurgy. In relation to downstream processes, it affects the fracture pattern during breakage, where rock strength is inherently a function of mineral texture. Because of the subjective nature of mineral texture, it has not been easy to quantify, especially in the context of a measurement suitable for use in geometallurgical programmes. The aim of this paper is to present the first steps in developing a 3D mineral texture quantification method for drill core and to assess its sensitivity to differences in rock strength using a case study. The methodology includes classifying the textural information using the 3D grey level co-occurrence matrices (GLCM) and X-ray computed tomography (XCT) coupled method. Rock strength tests were performed using the split Hopkinson pressure bar (SHPB). The case study investigates a heterogeneous polymetallic sulphide deposit and a homogeneous shale subdivided into three 'mineral textural types'. The variability is largely captured by the GLCM matrices, and preliminary trends can be observed where the shale is finer grained and has a higher yield strength in comparison with the coarser grained polymetallic sulphide ore.


  • Open Access

    Towards Standardising SHPB Testing - A Round Robin Exercise

    by Reuben Govender, Muhammad Kariem, Dong Ruan, Rafael Santiago, Dong Wei Shu, Marcilio Alves, Guoxing Lu, Gerald Nurick, Genevieve Langdon

    The Split Hopkinson Pressure Bar (SHPB) test, while widely utilised for high strain rate tests, has yet to be standardised. As an exploratory step towards developing a standard test method or protocol, a Round Robin test series has been conducted between four institutions: (i) Swinburne University of Technology, Australia (ii) University of São Paulo, Brazil, (iii) University of Cape Town, South African and (iv) Nanyang Technological University, Singapore. Each institution prepared specimens from a metallic material, and provided batches of specimens from their chosen material to the other institutions. The materials utilised in this round of testing were commercially pure copper and aluminium, magnesium alloy and stainless steel (316 grade). The intent of the first exercise is to establish the consistency of SHPB test results on nominally identical specimens at comparable elevated strain rates, conducted by different laboratories following notionally similar test procedures with some freedom in data processing. This paper presents and compares the results of the first batch of tests for copper, identifying variations between results from different laboratories. The variation between different laboratories’ results for copper is suffciently small that there is confidence in the potential to develop a draft standard in future.