SFSimeon Furrer

Simeon Furrer

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Simeon Furrer has a total of 40 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Magnetic Tape Storage Technology

    by Mark A. Lantz, Simeon Furrer, Martin Petermann, Hugo Rothuizen, Stella Brach, Luzius Kronig, Ilias Iliadis, Beat Weiss, Ed R. Childers, David Pease

    Magnetic tape provides a cost-effective way to retain the exponentially increasing volumes of data being created in recent years. The low cost per terabyte combined with tape’s low energy consumption make it an appealing option for storing infrequently accessed data and has resulted in a resurgence in use of the technology. Magnetic tape as a digital data storage technology was first commercialized in the early 1950’s and has evolved continuously since then. Despite its long history, tape has significant potential for continued capacity and data rate scaling. This article strives to provide an overview of linear magnetic tape technology, usage, history, and future outlook. After a short introduction, the article delves into the details of how modern tape drives and media operate, including the basic mechanism and physics of magnetic recording, current tape media technology, state-of-the-art tape head technology, tape layout and encoding, data retrieval, timing-based servo and mechatronics of a tape drive, and the capabilities of current drives. This is followed by a discussion of tape libraries, an overview of tape library performance modeling research, operating system-level and application-level tape support, tape use cases, and the future scaling potential and outlook of tape. The article concludes with a history of tape hardware, media, usage and software.


  • Track-following system optimization for future magnetic tape data storage

    by Patrick Ebermann, Giovanni Cherubini, Simeon Furrer, Mark A. Lantz, Angeliki Pantazi


  • 317 Gb/in2 Recording Areal Density on Strontium Ferrite Tape

    by Simeon Furrer, Patrick Ebermann, Mark A. Lantz, Hugo Rothuizen, Walter Haeberle, Giovanni Cherubini, Roy D. Cideciyan, Shinji Tsujimoto, Yoshihiro Sawayashiki, Noriko Imaoka, et al.

    The recording performance of a new prototype magnetic tape based on perpendicularly oriented strontium ferrite particles is investigated using a 29 nm wide tunneling magnetoresistive reader. At a linear density of 702 kbpi, a post-detection byte-error rate of 2.8e-2 is demonstrated based on measured recording data and a software read channel. The read channel uses a 64-state implementation of an extended version of a data-dependent noise-predictive maximum-likelihood detection scheme that tracks the first and second order statistics of the data-dependent noise. At the demonstrated post-detection byte-error rate, a post-error-correction-coding byte-error rate of less than 1e-20 can be achieved using an iterative decoding architecture. To facilitate aggressive track-density scaling, we made multiple advances in the area of track following. First, we developed a new timing-based servo pattern and implemented a novel quad channel averaging scheme. Second, we developed a new field programmable gate array prototyping platform to enable the implementation of quad channel averaging. Third, we enhanced our low disturbance tape transport with a pair of 20 mm diameter air bearing tape guides and a prototype track-following actuator. Fourth, we developed a novel low friction tape head and finally, we designed a set of tape speed optimized track-following controllers using the model-based H∞ design framework. Combining these technologies, we achieved a position error signal (PES) characterized by a standard deviation ≤ 3.18 nm over a tape speed range of 1.2 to 4.1 m/s. This magnitude of PES in combination with a 29 nm wide reader enables reliable recording at a track width of 56.2 nm corresponding to a track density of 451.9 ktpi, for an equivalent areal density of 317.3 Gb/in2.


  • Performance of Interleaved Block Codes With Burst Errors

    by Roy D. Cideciyan, Simeon Furrer, Mark A. Lantz

    A Gilbert-Elliott channel for symbol errors is considered to analyze the performance of interleaved error correction codes with a fixed block size in the presence of burst errors. The proposed channel model for symbol errors is based on a simplified Gilbert channel for bit errors, which enables direct comparisons of the performance of block codes with different symbol sizes. The autocorrelation function between two erroneous symbols within an interleaved codeword is computed. An exact expression for the codeword-error probability is derived from the symbol-based channel model. A tight lower bound on the codeword-error probability and error floors, which are observed when the average raw bit-error rate is low, are analyzed using the bit-based channel model.


  • Design Techniques for High-Speed Multi-Level Viterbi Detectors and Trellis-Coded-Modulation Decoders

    by Hazar Yueksel, Matthias Braendli, Andreas Burg, Giovanni Cherubini, Roy D. Cideciyan, Pier Andrea Francese, Simeon Furrer, Marcel Kossel, Lukas Kull, Danny Luu, et al.

    The implementation of a 25.6-Gb/s four-level pulse-amplitude-modulation (4-PAM) reduced-state sliding-block Viterbi detector (VD) is presented. The power consumption of the VD is 105,mW at a supply voltage of 0.7 V, corresponding to an energy efficiency of 4.1 pJ/b. A data rate of 30.4 Gb/s is achieved with an energy efficiency of 5.3 pJ/b at a supply voltage of 0.8 V. The VD, implemented in an experimental chip fabricated in 14-nm CMOS FINFET, exploits set-partitioning principles and embedded per-survivor decision feedback to reduce implementation complexity and power consumption. The active area of the VD with 12 slices, each operating at one-eighth of the modulation rate, is 0.507 x 0.717 mm². Experimental results showing system performance are obtained by using a (2¹⁵ - 1)-bit pseudo-random binary sequence. The impact of the synchronization length and survivor path memory length on the detector design and system performance are shown. A new pipelined reduced-state sequence detector algorithm is presented for high-speed implementations. A novel speculative symbol timing recovery scheme is proposed. New simulation results are obtained to compare the performance of the Reed-Solomon (RS)-encoded 4-PAM scheme with that of the concatenated RS 4-D 5-PAM trellis-coded-modulation (TCM) scheme over an ideal band-limited additive-white-Gaussian-noise channel. Drawing on the results achieved for the VD, novel design techniques for a high-speed low-complexity eight-state 4-D 5-PAM TCM decoder is proposed.


  • Product Codes for Data Storage on Magnetic Tape

    by Roy D. Cideciyan, Simeon Furrer, Mark A. Lantz

    For 2-D product codes used in tape storage, the mapping of error-correction-coding (ECC) blocks (EBs) into 2-D physical blocks (PBs) on magnetic tape is generalized. The 3-D product codes that have the same code rate and EB size as interleaved 2-D product codes currently used in tape storage are proposed. For 3-D product codes, a new family of mappings of EBs into 2-D PBs on magnetic tape is introduced, which fulfills the stringent burst-error-correction requirements of tape storage. The burst-error-correction capability of 2-D and 3-D product code words recorded on magnetic tape is analyzed as a function of track rotation, linear density, and ECC parameters. The performance limits of the tape-storage channel are determined based on computations of channel capacity and random coding bound. Hardware simulations of iterative hard-decision decoding of product codes implemented in a field-programmable gate array demonstrate the improved error-rate performance of 3-D product codes over 2-D product codes.


  • High-Rate Skew Estimation for Tape Systems

    by Giovanni Cherubini, Simeon Furrer, Mark A. Lantz

  • Resolution Limits of Timing-Based Servo Schemes in Magnetic Tape Drives

    by Simeon Furrer, Angeliki Pantazi, Giovanni Cherubini, Mark A. Lantz

    The resolution limits of tape head lateral position estimates derived from timing-based servo (TBS) patterns preformatted on perpendicularly oriented barium ferrite tape media are investigated. A set of four new TBS patterns with azimuth angles ranging from 15° to 24° but having, otherwise, identical parameters are compared. Measurements of the standard deviation of the closed-loop position-error signal are compared with resolution estimates based on: 1) the noise floor of the power spectral density of the lateral tape motion measured from the servo pattern during open or closed-loop track-following and 2) an analytical lower bound on the mean-squared estimation error, which depends on the servo readback signal shape and the signal-to-noise ratio. All four servo patterns are shown to achieve nanoscale resolution under realistic operating conditions. The 24° pattern was found to provide the highest performance with a position estimation resolution better than 3.8 nm for a single channel, and better than 2.6 nm when the estimates of two channels are combined.